Q6600 + P5q-e

[gugle]

how I can to improve these values?
PLL, GTL's, vNB, Clock Skew

Q6600 VID 1.2500v
450x8 - 3600mhz
4x1Gb DDR2- 1080

CPU Voltage	1,41250v
CPU GTL Voltage Reference (0/2) 0.630 -- correct?
CPU GTL Voltage Reference (1/3) 0.670 -- correct?
CPU PLL Voltage	1,52
FSB Termination Voltage	1,28
DRAM Voltage 2.10
NB Voltage	1.18
NB GTL Reference 0.630 -- correct?
SB Voltage	1.10
PCIE Voltage 1.50
____________________________________	
	
Load-Line Calibration	[Enabled]
CPU Spread Spectrum	[Disabled]
PCIE Spread Spectrum	[Disabled]
CPU Clock Skew	[Auto]
NB Clock Skew	[Auto]
CPU Margin Enhancement [Optimized Mode]
____________________________________	
	
Advance CPU Settings:	
CPU Ratio Setting:	
C1E Support:	[Disabled]
Max CPUID Value Limit:	[Disabled]
Intel Virtualization Tech:	[Disabled]
CPU TM Function:	[Disabled]
Execute Disable Bit:	[Disabled]

[avercros]

Hi
-----------------------------------

Q6600 VID 1.2500v
450x8 - 3600mhz
4x1Gb DDR2- 1080

CPU Voltage 1,41250v----TOO HIGH try 1.37 or 1.39
CPU GTL Voltage Reference (0/2) 0.630 -- correct? OK
CPU GTL Voltage Reference (1/3) 0.670 -- correct? OK
CPU PLL Voltage 1,52 set 1.54
FSB Termination Voltage 1,28 OK
DRAM Voltage 2.10
NB Voltage 1.18---- set 1.22
NB GTL Reference 0.630 -- correct? OK, but try AUTO
SB Voltage 1.10-----set AUTO
PCIE Voltage 1.50----set AUTO
____________________________________

Load-Line Calibration [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Clock Skew [Auto]
NB Clock Skew [Auto]
CPU Margin Enhancement [Optimized Mode]
____________________________________

Advance CPU Settings:
CPU Ratio Setting: 8
C1E Support: [Enabled]
Max CPUID Value Limit: [Disabled]
Intel Virtualization Tech: [Enabled]
CPU TM Function: [Disabled]
Execute Disable Bit: [Enabled]

[Leeghoofd]

If your settings are stable Gugle, don't change a thing !

[carepolice]

1.41xxx Vcore for 65nm isnt too much, just keep your settings as leeg said above.

[Vazovskiiii]

Q6600 VID 1.2500v
450x8 - 3600mhz
4x1Gb DDR2- 1080

CPU Voltage 1,41250v----TOO HIGH try 1.37 or 1.39
CPU GTL Voltage Reference (0/2) 0.630 -- correct? OK
CPU GTL Voltage Reference (1/3) 0.670 -- correct? OK
CPU PLL Voltage 1,52 set 1.54
FSB Termination Voltage 1,28 OK
DRAM Voltage 2.10
NB Voltage 1.18---- set 1.22
NB GTL Reference 0.630 -- correct? OK, but try AUTO
SB Voltage 1.10-----set AUTO
PCIE Voltage 1.50----set AUTO
____________________________________

Load-Line Calibration [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Clock Skew [Auto]
NB Clock Skew [Auto]
CPU Margin Enhancement [Optimized Mode]
____________________________________

Advance CPU Settings:
CPU Ratio Setting: 8
C1E Support: [Enabled]
Max CPUID Value Limit: [Disabled]
Intel Virtualization Tech: [Enabled]
CPU TM Function: [Disabled]
Execute Disable Bit: [Enabled]



-----------------------------------

hallo i've used this settings this is really great but plz could you write down settings for same configuration on 3.2mhz? i have transcend axeram 1200+ plz it would be great

thank you

[fragsta]

bios version pls? have the setup... thx

[Loser777]

What PSU are you using with that? (Just want to know because I'm trying to get my system stable.

[Leeghoofd]

hallo i've used this settings this is really great but plz could you write down settings for same configuration on 3.2mhz? i have transcend axeram 1200+ plz it would be great

thank you

AI Overclock tuner: Manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: AUTO
FSB Frequency: 400
PCI-E Frequency: 101
DRAM Frequency: 1200
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 45
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

DRAM Static Read Control: DISABLED
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO --> test first then try MODERATE if no go LIGHT
AI Transaction Booster: AUTO --> test first then Enable later try eg 9



CPU Voltage 1,4v (depending on ya CPU)
CPU GTL Voltage Reference (0/2) AUTO
CPU GTL Voltage Reference (1/3) AUTO
CPU PLL Voltage : 1,56
FSB Termination Voltage : 1,3
DRAM Voltage : 2.20 (depending on ya ram)
NB Voltage : 1.26
NB GTL Reference : AUTO
SB Voltage : AUTO
PCIE Voltage : AUTO
____________________________________

Load-Line Calibration [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Clock Skew [Auto]
NB Clock Skew [Auto]
CPU Margin Enhancement [Optimized Mode]
____________________________________

Advance CPU Settings:
CPU Ratio Setting: 8
C1E Support: [Enabled]
Max CPUID Value Limit: [Disabled]
Intel Virtualization Tech: [Enabled]
CPU TM Function: [Disabled]
Execute Disable Bit: [Enabled]

What PSU are you using with that? (Just want to know because I'm trying to get my system stable.

Swap your ram first loser... and you got 3 years warranty on that Corsair... do something about it instead of posting a zillion times the same thing. You have been unstable for months always telling us it's the PSU. RMA it then or try something else... you got a nice CPU now, time to swap something else dude, as just complaining about it will NOT get you any further...

[gugle]

thanks for tips

Bios 1406

my PSU is a Enermax EG495P-VE (485w)

the temperature is too high at 3.6ghz, moved for now to 3.2ghz

Q6600 VID 1.2500v
Asus P5Q-E Bios 1406
4x1Gb DDR-2 800+ Transcend AxeRam

400x8 - 3200 Mhz
DDR2-1000 5 5-5-15 2T

CPU Voltage: 1.26250v
CPU GTL Voltage Reference (0/2): 0.630
CPU GTL Voltage Reference (1/3): 0.630
CPU PLL Voltage: 1.50v
FSB Termination Voltage: 1.28v
DRAM Voltage: 2.00v
NB Voltage: 1.18v
NB GTL Reference : 0.630
SB Voltage: 1.10v
PCIE Voltage: 1.50

[gugle]

is for (500x7) 3500mhz, as voltage need?

500x7
DDR2-1000

CPU Voltage: ---v
CPU GTL Voltage Reference (0/2): 0.630 ??
CPU GTL Voltage Reference (1/3): 0.650 ??
CPU PLL Voltage: 1.52v ??
FSB Termination Voltage: 1.32v ??
DRAM Voltage: 2.00v
NB Voltage: 1.35v ??
NB GTL Reference : 0.630 ??
SB Voltage: 1.10v ??
PCIE Voltage: 1.50

[Vazovskiiii]

thank you all my frien i will trythis settings my bios is 1406 but i think that there is some problems with my 1200 mhz rams

my PSU is RECOM 600 WAT CABLE FREE

[Vazovskiiii]

i have tried your settings but system is not stable

[gugle]

What is your memory?

voltages which you have placed in the bios?

[Vazovskiiii]

What is your memory?

voltages which you have placed in the bios?

Transcend axeram 1200mhz+ 2.2voltages