Live MB OC Report :: ASUS Rampage Extreme

[coral11]

CPU Type: E8600
Cooling: H2o
Bios version: 0501
OS: Vista 64
Graphics card(s): GTX 280
Memory Brand and speed: Corsair CM3X2G1600DHX 1600 4 gigs

Tweaker Menu (Bios version 0501)
Ai Overclock Tuner: Manual
OC From CPU Level Up: Auto
OC From Memory Level Up: Auto
FSB Frequency: 400
CPU Ratio Setting: 10
>> = sub menu
>>CPU Configuration
>>CPU Ratio Setting: 10
>>C1E Support: Disabled
>>CPU TM Function: Enabled
>>Max CPUID Value Limit: Disabled
>> Vanderpool Technology: Disabled
>> Execute Disable Bit: Enabled
>> Core Multi-Processing: Enabled
CPU Clock Skew: Auto
NB Clock Skew Auto
FSB Strap to North Bridge: Auto
PCIE Frequency: 100
DRAM Frequency: DDR-1601
DRAM Command Rate: 2N
DRAM Timing Control: Manual
1st Information: 9-9-9-24-5-8-12-6
CAS# Latency: 9
RAS# to CAS# Delay: 9
RAS# Pre Time: 9
RAS# ACT Time: 24
RAS# To RAS# Delay: Auto
REF Cycle Time: Auto
WRITE Recovery Time: Auto
READ to Pre Time: Auto
2nd Information: 10-6-5-4-7-4-7
READ to WRITE Delay (S/D): Auto
WRITE to READ Delay (S): Auto
WRITE to READ Delay (D): Auto
READ to READ (S): Auto
READ to READ (D): Auto
WRITE to WRITE (S): Auto
WRITE to WRITE (D): Auto
3RD Information: 24-8-1-10-10
WRITE to PRE Delay: Auto
READ to PRE Delay: Auto
PRE to PRE Delay: Auto
ALL PRE to ACT Delay: Auto
ALL PRE to REF Delay: Auto
DRAM Static Read Control: Auto
DRAM Dynamic Write Control: Auto
>> = sub menu
>>DRAM Skew Control
>>DRAM CMD Skew on Channel A: Auto
>>DRAM CLK Skew on DIMM A1: Auto
>>DRAM CLK Skew on DIMM A2: Auto
>>DRAM CTL Skew on DIMM A1: Auto
>>DRAM CTL Skew on DIMM A2: Auto
>>DRAM CMD Skew on Channel B: Auto
>>DRAM CLK Skew on DIMM B1: Auto
>>DRAM CLK Skew on DIMM B2: Auto
>>DRAM CTL Skew on DIMM B1: Auto
>>DRAM CTL Skew on DIMM B2: Auto
Ai Clock Twister: Auto
Ai Transaction Booster: Auto
EPU II Phase Control: Auto
CPU Voltage: Auto
Load-Line Calibration: Auto
CPU PPL Voltage: Auto
FSB Termination Voltage: Auto
CPU GTLVerf (0): Auto
CPU GTLVerf (1): Auto
CPU GTLVerf (2): Auto
CPU GTLVerf (3): Auto
NB GTLVerf: Auto
North Bridge Voltage: Auto
DRAM Voltage: 1.8
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: Auto
South Bridge 1.05 Voltage: Auto
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Under advanced menu:
North Bridge Chipset Configuration
Memory Remap Feature: Enabled
Initiate Graphic Adapter: PEG/PCI
PEG Port Control: Auto

These are my current settings, what should I change to get to my target?

Thanks