ASUS P5Q3 Deluxe discussion

[BNDMOD]

now i probe

i Overclocker Tuner: Manual
CPU Ratio Setting: 07.0
FSB Frequency: 600
PCIE Frequency: 100
FSB Strap To North Bridge: AUTO
DRAM Frequency: All Speed
DRAM CLK Skew on Channel A1: Auto
DRAM CLK Skew on Channel A2: Auto
DRAM CLK Skew on Channel B1: Auto
DRAM CLK Skew on Channel B2: Auto
DRAM Timing Control: Manual
CAS Latency: 7-8
DRAM RAS to CAS Delay: 7-8
DRAM RAS Precharge: 7-8
DRAM RAS Activate to Precharge: 18-24
RAS TO RAS Delay: Auto-8-9-10
Row Refresh Cycle Time: AUTO-82
Write Recovery Time: Auto
Read To Precharge Time: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled
DRAM Read Training: Disabled
DRAM Write Training: Disabled
MEM OC Charger: Auto-Disable
Ai Clock Twister: AUTO-Ligther
AI Transaction Booster: AUTO-PL 11-7

CPU Voltage: 1.3v-1.4
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: 1.54-1.6
FSB Termination Voltage: 1.4-1.6
DRAM Voltage: 1.9-1.96
NB Voltage: 1.4-1.55
NB GTL Voltage: Auto or 0.545
SB Voltage: AUTO
PCIE SATA Voltage: Auto
Load-Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew: AUTO-200-400
NB Clock Skew: AUTO-200

For 600 FSB doesn-t work :s

But for 4Ghz 4.1-4.2-4.3-4.4-4.5 Ghz this setting work

i Overclocker Tuner: Manual
CPU Ratio Setting: 10.0
FSB Frequency: 400-410-420-430-450
PCIE Frequency: 100
FSB Strap To North Bridge: AUTO
DRAM Frequency: All Speed
DRAM CLK Skew on Channel A1: Auto
DRAM CLK Skew on Channel A2: Auto
DRAM CLK Skew on Channel B1: Auto
DRAM CLK Skew on Channel B2: Auto
DRAM Timing Control: Manual
CAS Latency: 7-8
DRAM RAS to CAS Delay: 7-8
DRAM RAS Precharge: 7-8
DRAM RAS Activate to Precharge: 18-24
RAS TO RAS Delay: Auto
Row Refresh Cycle Time: AUTO
Write Recovery Time: Auto
Read To Precharge Time: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled
DRAM Read Training: Disabled
DRAM Write Training: Disabled
MEM OC Charger: Auto-Disable
Ai Clock Twister: AUTO-Ligther
AI Transaction Booster: AUTO-PL 11-7

CPU Voltage: 1.3v-1.4
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: 1.54-1.6
FSB Termination Voltage: 1.4-1.6
DRAM Voltage: 1.9-1.96
NB Voltage: 1.4-1.55
NB GTL Voltage: Auto or 0.545
SB Voltage: AUTO
PCIE SATA Voltage: Auto
Load-Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew: AUTO-200-400
NB Clock Skew: AUTO-200

[Amurtigress]

now i probe



For 600 FSB doesn-t work :s

But for 4Ghz 4.1-4.2-4.3-4.4-4.5 Ghz this setting work

BND: It is likely that the board is changing the FSB Strap once you hit 600. I'd recommend to see which FSB strap is active and stable below 600 and then set this strap manually. Just guessing...I remember on the P5B Deluxe when people were getting to FSB 400 it all got stable but from 366-399 there was a stability hole...

[BNDMOD]

BND: It is likely that the board is changing the FSB Strap once you hit 600. I'd recommend to see which FSB strap is active and stable below 600 and then set this strap manually. Just guessing...I remember on the P5B Deluxe when people were getting to FSB 400 it all got stable but from 366-399 there was a stability hole...

So you recommend me to set FSB strap 200/266/333/400 to test and get estability?

[Amurtigress]

So you recommend me to set FSB strap 200/266/333/400 to test and get estability?

Yes. the FSB strap is being adjusted at certain FSB clocks when set to auto. To keep that from happening set a FSB strap AND DRAM frequency manually.

[BNDMOD]

Yes. the FSB strap is being adjusted at certain FSB clocks when set to auto. To keep that from happening set a FSB strap AND DRAM frequency manually.

I-ve tried to set fsb strap but i doesn-t work too :s