Water Cooled Case Gallery

[twwen2]

@ natech: nice rig mate, i'm liking it

@ eternal_fantasy: Some nice hardware you got there! One question, is the GPU block a Zalman, and if so is it Aluminium? If you answered yes to both those questions, you might want to watch the loop very carefully

[peQs]

EK DUAL LAING TURBO TOP + 2 x Laing 12V DDC-1Plus

[slim142]

Thx skinnee
Now if they could just make it 1/2 like you said, it would be the perfect heatsink city.

[callen_1]

@natech, that looks great as is. It's gonna look awsome once its finished. btw was it difficult to bleed the system with the pumps almost at the highest point? Or did you just tip on the side?

@eternal_fantasy. nice hardware, looks good too.

[natech]

Thanks all for the comments.

IanY, im going to take this thing apart in about a week or so, I hope it last that long. When rebuilding im going to remember your comment and maybe use zipties. Or better yet, one of these:
if I could find them in finland in right size and reasonable price.

callen_1, it was surprisingly easy. I had to place the case to many different positions though.

[Zeus]

Thanks all for the comments.

IanY, im going to take this thing apart in about a week or so, I hope it last that long. When rebuilding im going to remember your comment and maybe use zipties. Or better yet, one of these:
if I could find them in finland in right size and reasonable price. They tend to cost something like 5EUR/piece.

callen_1, it was surprisingly easy. I had to place the case to many different positions though.

Five euro's?

€1,59 a piece at www.aquatuning.de

[eternal_fantasy]

@ eternal_fantasy: Some nice hardware you got there! One question, is the GPU block a Zalman, and if so is it Aluminium? If you answered yes to both those questions, you might want to watch the loop very carefully

Thanks, and luckily that's a negitive to both
It is a Blastflow 9800GX2 waterblock with a copper core, and an aluminum heat plate for the rams and mosfet;

The block's internals;

No aluminium ever touches my coolent

@eternal_fantasy. nice hardware, looks good too.

Thanks, callen

[natech]

Zeus that was fast. I edited that cost part off like in 15seconds

I'm tempted to buy something from aquatuning too, becourse we don't have that good shops in finland. I didn't even find right size screw-on fittings.
Found them on aquatuning though, they cost 5,99 EUR/piece in there.
(16/13mm screw-on fitting straight G1/4"). As it is pretty much but I think the price is still acceptable for something as cool as those

Thanks for your help

[Xelation]

So confused on what to do, got the TFC Xchanger 360 Triple in my Cosmos S.
The radiator is so big that it won't/can't fit under the hood of the case. So my
Noctua fans are blowing heat away instead of blowing air from underneath.

The thing is the TFC Xchanger 360 Triple is the best radiator, but now it's not
cooled properly. My second choice would have been the 360 thing Black Ice with the
Noctua's underneath and on top under the roof for optimal cooling.

Any suggestions?

[inCore]

Five euro's?

€1,59 a piece at www.aquatuning.de

If you only want to buy those, you can e-mail aquatuning and they might send them to you in a letter. When I tried ordering them through the normal shop, I was quoted €27,50 for shipping, but this might be because Switzerland isn't in the EU.

[twwen2]

Thanks, and luckily that's a negitive to both
It is a Blastflow 9800GX2 waterblock with a copper core, and an aluminum heat plate for the rams and mosfet;

No aluminium ever touches my coolent

Good man . That actually doesn't look too bad either!

[masacre]

Thanks, and luckily that's a negitive to both
It is a Blastflow 9800GX2 waterblock with a copper core, and an aluminum heat plate for the rams and mosfet;

The block's internals;

No aluminium ever touches my coolent


Thanks, callen

OMG



-------------------------------------
on the fly nigth shots

[callen_1]

Thought i was on acid for a sec there , nah thats cool

[CyberDruid]

Looks like a flattening tube to the pump inlet...may want to put a UV reactive cable tie there

[hewi]

Thanks all for the comments.

IanY, im going to take this thing apart in about a week or so, I hope it last that long. When rebuilding im going to remember your comment and maybe use zipties. Or better yet, one of these:
if I could find them in finland in right size and reasonable price.

callen_1, it was surprisingly easy. I had to place the case to many different positions though.

I wish you luck in finding those compression fittings here in Finland, they do sell em in Coolputer.fi etc. but biggest size you'll get is 11/9mm and your tubing looks more like 3/8" or 1/2" it's a bummer we get so limited amount of good WC parts here.

I know this ain't a sales forum but if you are interested in some Feser 1/2" ID 3/8" OD compression fittings like these http://www.chilledpc.co.uk/shop/imag...ture%20200.jpg I have 12 pieces that became useless after I downgraded tubes for a mATX build. Shoot me a PM if ur interested I live in the capitol area

[masacre]

Looks like a flattening tube to the pump inlet...may want to put a UV reactive cable tie there

If it is true is smooth in a little but this is a very closed the angle of the pipe. Unfortunately I did not find a better place for the pump

Either way not cut circulation and affects very little power is controlled this Angulo

[yazýcýoðlu]

[MaxHardware]

previus setup:







New Setup:












View Worklog: click here

[Yozzman]

Looks nice!!!

But why not use the inlet on top?
That will give the best performance!

[MomijiTMO]

2 pumps = who cares Plus the Koolance ram coolers are restriction central. If they have enough rad area then all will manage.

Some people do like their looks but I'm not one of them lol.

[Colossous]

After an accident involving a wet fire escape and a Lian Li V2100 case i rescuesd what i could and did this to it.
Full thread here :-http://www.xtremesystems.org/forums/...d.php?t=193211

[CyberDruid]

That's CRAZY. And I mean in a good way

[Colossous]

Cheers CyberDruid - it has come out a bit mad lol ! Going to install it tonight and see how it runs

[skinnee]

@Colossous
Can we get a few more pics, I see you chopped it, but I can't really see what all has changed. Really curious to see what all you had to chop and how it all turned out.

[Mankz_91]