"ASUS P5Q Deluxe discussion".

[MonsterDK]

HELP NEEDED PLEASE

Just had a out of the blue reboot.

On booting back up Windows XP loaded then there is a small pause while the DVDRW etc is read and such then the final parts to loading the OS usually continue to load - but it reboots and ends up in a cycle.

I've had to turn off PC at the PSU switch then back on.. now it will boot ok into the OS.

I've checked event viewer and I can't see anything that is revealing anything.

Anyone have any suggestions if this could be hardware related or OS?

Will my PSU be ok for the hardware below?

Mobo: Asus P5Q Del (latest bios)
PSU: Corsair 620w
Q6600 (G0)
4GB Crucial Ballistix
ATI Radeon 3780 GC
2 x 1TB WD HDD
1 x 1TB Samsung spinpoint
1 x 500gb WD (Vista OS)
2 x 160GB WD in Raid0 (Win XP Pro 64 OS)
3 x scyte 120mm case fan
1 x 120mm fan on CPU cooler
2 x 80mm case fans
1 large side fan (with thermaltake case)
2 x DVDRW drives


AI Overclock tuner: Manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: 333
FSB Frequency: 333
PCI-E Frequency: 101
DRAM Frequency: 1066Mhz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Auto
MEM. OC Charger: Auto
AI Clock Twister: Auto
AI Transaction Booster: Manual
Common Performance Level [8]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.26875
CPU GTL Voltage Reference (0/2): 0.630
CPU GTL Voltage Reference (1/3): 0.670
CPU PLL Voltage: 1.58
FSB Termination Voltage: 1.28
DRAM Voltage: 2.12
NB Voltage: 1.24
NB GTL Reference: 0.630
SBridge Voltage: Auto
PCIE SATA Voltage: Auto

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal

All CPU extras Disabled.

Any help appreciated.