Hey whats up guys? I'm new here and just got around to overclocking my board finally! Here's what I got:

http://valid.x86-secret.com/show_oc.php?id=380932

Also here are my settings:

ASUS P5Q DLX Template :

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 7.5 (6.5 does not work, 6 is reported by windows utilities)
FSB Strap to North Bridge: 400
FSB Frequency: 533
PCI-E Frequency: Auto
DRAM Frequency: 1066
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO

1st Information :

CAS# Latency: AUTO
DRAM RAS# to CAS# Delay: AUTO
DRAM RAS# Precharge: AUTO
DRAM RAS# Activate to Precharge: AUTO
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Disabled (enabling this made my ram fail memory stress tests)
AI Clock Twister: Strong (the closer you put this to Stronger the lower latency you get as reported by Everest Cache & Memory Benchmark, Stronger would not boot for me unless I added a lot more vdimm)
AI Transaction Booster: Manual
Common Performance Level [10]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.3875v (reported by CPU-Z at 1.384v during full load)
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: AUTO
FSB Termination Voltage: AUTO
DRAM Voltage: 2.18v
NB Voltage: 1.26v
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto

Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Enabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Enabled

So far this setup is Prime stable for an hour, will run it longer tonight. I can't really go higher on the FSB because my ram has very bad compatibility with this board, it will barely clock over 1066mhz without failing memory stress testing. On my old BFG 680i SLI board this ram would get over 1150mhz stable! I could even set it to 4-4-4-12 if i left it at 1066mhz and put the voltage to 2.15v, not on this board though! All my overclocking is done using BIOS 0704.