Foxconn BlackOPS (Retail version)

[raptor1]

Hi!

Has anyone any luck at overclocking an E8500 chip at 450 /500 FSB

if so can they post their settings

I was stable with my SIIE for a while, but typically this board works fine for a while and then decides to go back to crashing and freezing

i am hoping to to get the blackops board, but want to make sure the E8500 will work fine first

thanks
flanr

[dread77]

Hi!

Has anyone any luck at overclocking an E8500 chip at 450 /500 FSB

if so can they post their settings

I was stable with my SIIE for a while, but typically this board works fine for a while and then decides to go back to crashing and freezing

i am hoping to to get the blackops board, but want to make sure the E8500 will work fine first

thanks
flanr

Well, at least for now, 500 fsb seems like mission impossible on this board. I managed to boot using 8X500, though it was not benchable at all. Just a winrar test and then it crushed. I tried several combinations with the timings but no luck. I someone else can give us stable settings for 500 fsb I would appreciate it as well.

460 and 470 though, is pretty easy on this board but again it's pretty low for an E8500. This board was built only for unlocked multipliers and that is final... aka QX9XXX

[boblemagnifique]

I have test today the news BlackOps X48

First test with the bios 05/09 on max freq DDR3 (STT DDR3 1800 ProjectX) on single at 2.2v

http://valid.x86-secret.com/show_oc.php?id=369787

[dread77]

I have test today the news BlackOps X48

First test with the bios 05/09 on max freq DDR3 (STT DDR3 1800 ProjectX) on single at 2.2v

http://valid.x86-secret.com/show_oc.php?id=369787

Can you post your sub timmings/settings on this one mate???

[boblemagnifique]

Can you post your sub timmings/settings on this one mate???

it's just the First Test (i don't really found the good setting for the moment )



http://valid.x86-secret.com/show_oc.php?id=369849

TRFC : 69
Perf Level : 7
Write to precharge delay : 23
TWTR : 21
TRRD : 5
TRD_WR : 10
TRTP : 5

Vcore : 1.265v
Vpll : 1.584v
Vvtt : 1.575v
NB : 1.594v
SB : 1.613v
Vddr : 2.21v

I test tommorow with the E8500 , for the moment i test my QX9650/BlacKops/9800GX2 under Cascade 2 stages

[raptor1]

Well, at least for now, 500 fsb seems like mission impossible on this board. I managed to boot using 8X500, though it was not benchable at all. Just a winrar test and then it crushed. I tried several combinations with the timings but no luck. I someone else can give us stable settings for 500 fsb I would appreciate it as well.

460 and 470 though, is pretty easy on this board but again it's pretty low for an E8500. This board was built only for unlocked multipliers and that is final... aka QX9XXX

if you have time can you or someone check for 450 x9 which gave me roughfully 4.05 ghz on my Striker II Extreme - i know it is pretty low but i would be happy with this and with 100% stability

[dread77]

No problem mate. I will post my settings later when I will get home (I am supposed to be working right now ). I have solid 9X450 24/7 settings . Are you running your system on air cooling??? NB temps can get preety high (47 idle), though my room temps are 27-30C (I leave in sunny Greece).

[raptor1]

No problem mate. I will post my settings later when I will get home (I am supposed to be working right now ). I have solid 9X450 24/7 settings . Are you running your system on air cooling??? NB temps can get preety high (47 idle), though my room temps are 27-30C (I leave in sunny Greece).

i will be running on air with a thermalight ultra 120 extreme cpu cooler with a scythe 120mm fan attached and i will probably get a cooler for the NB

[dread77]

i will be running on air with a thermalight ultra 120 extreme cpu cooler with a scythe 120mm fan attached and i will probably get a cooler for the NB

Well, you can't get a separate cooler on the NB unless you dettach the whole copper cooling system from the board. W/C would be more appropriate.

[raptor1]

Well, you can't get a separate cooler on the NB unless you dettach the whole copper cooling system from the board. W/C would be more appropriate.

got this from blackops product page on foxconn website

http://www.quantum-force.net/Products/P000000002/