Right now Im set up at 3.6 prime stable at 4.4.4.12 and at good temps but with this new ram mushkin 4g (996580) ram I cant figure the subtimings of this board to get it to 900mhz or 1000mhz can anyone give me some helpfull tips to get some bandwitdh outa these sticks


12/24

Code:
CPU Feature
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio: 9X
- Target CPU Clock: 3600 MHz
CPU Clock: 400 MHz
Boot Up Clock: auto
DRAM Speed: 333/667
- Target DRAM Speed: 800MHz
PCIE Clock: 100mhz

Voltage Settings
CPU VID Control: 1.4125V
CPU VID Special Add: auto
DRAM Voltage Control: 2.310V
SB 1.05V Voltage: 1.150V
SB Core/CPU PLL Voltage: 1.95V
NB Core Voltage: 1.55V
CPU VTT Voltage: 1.52V
Vcore Droop Control: disabled
Clockgen Voltage Control: 3.85v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Enable
x CPU GTL1/3 REF Volt: 106
x CPU GTL 0/2 REF Volt: 107
x North Bridge GTL REF Volt: 117

DRAM Timing
- Enhance Data transmitting: Fast
- Enhance Addressing: Fast
- T2 Dispatch: Disabled AUTO

Clock Setting Fine Delay
Ch1 Clock Crossing Setting: AUTO
- DIMM 1 CLK fine delay: ?
- DIMM 2 CLK fine delay: ?
- Ch 1 Command fine delay: ?
- Ch 1 Control fine delay: ?

Ch2 Clock Crossing Setting: AUTO
- DIMM 3 CLK fine delay: ?
- DIMM 4 CLK fine delay: ?
- Ch 2 Command fine delay: ?
- Ch 2 Control fine delay: ?

Ch1Ch2 CommonClock Setting: Auto

Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto

Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto (where cpuz sees 1T or 2T SETTING)

CAS Latency Time (tCL): 4
RAS# to CAS# Delay (tRCD): 4
RAS# Precharge (tRP): 4
Precharge Delay (tRAS): 12
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay) (tRD): AUTO

Read delay phase adjust: Enter
- Channel 1 Phase 0 Pull-In: Auto (each Phase when enabled = (Common tRD - 1)
- Channel 1 Phase 1 Pull-In: Auto
- Channel 1 Phase 2 Pull-In: Auto
- Channel 1 Phase 3 Pull-In: Auto
- Channel 1 Phase 4 Pull-In: Auto

- Channel 2 Phase 0 Pull-In: Auto
- Channel 2 Phase 1 Pull-In: Auto
- Channel 2 Phase 2 Pull-In: Auto
- Channel 2 Phase 3 Pull-In: Auto
- Channel 2 Phase 4 Pull-In: Auto

MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO

PCIE Slot Config: 1X 1X
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled