MMM
Results 1 to 25 of 1681

Thread: **Official DFI LanParty UT 790FX-M2R Review/Overclock/Guide Thread**

Threaded View

  1. #11
    uncore challenged...
    Join Date
    Feb 2006
    Location
    ontari-ho (canada)
    Posts
    1,654
    hey cats, as mentioned, i decided to give this board another try and things have been going really well after exchanging with that board stuck at 133MHz. that is until i reached 281MHz HTT. 281MHz HTT is Prime/3D stable for hours on end, never a problem. going up to 282MHz HTT results in a hang at 25 during POST. this is with two Phenoms or the 3200+. same exact results with all three. BIOS i am running is the latest official 01/30 FWIW.

    i would like to see if i can get above 281MHz HTT in Windows but not sure which version of AOD or ClockGen will work, any advice would be great.

    obviously i would also like to get past this spot from within the BIOS as well. i have tried pretty much everything in Genie BIOS section and can't get 282MHz HTT+ to POST. here is the timing sheet i am working with right now, any help would be appreciated:

    Code:
    Genie BIOS Settings:
    Timing Mode.......................... - Disabled
    Memory Clock......................... - DDR800 (1:2)
    PCIE 3,4 State....................... - x16.NC
    PCIE 2 State......................... - x2
    AMD Cool & Quiet..................... - Disabled
    CPU Clock Ratio...................... - Auto
    Spread Spectrum...................... - Disabled
    CPU Host/HTT Clock................... - 281MHZ
    CPU Host/HTT Boot Up Clock........... - 250MHZ
    CPU Host/HTT Adjust Gap.............. - 5
    PCI-E Clock.......................... - 101MHZ
    
    >DRAM Configuration:
    MCT Memory Timing................... - Manual
    2T Mode............................. - Enabled
    Cas Latency Time.................... - 5
    Pre Charge Delay (tRAS)............. - 8
    DRAM RAS# Precharge................. - 5
    DRAM RAS# to CAS# Delay............. - 5
    Bank to Bank Cmd (TRRD)............. - Auto
    TRC................................. - 13
    TRTP................................ - Auto
    Write Recovery (TWR)................ - Auto
    Write-Read Command (TWTR)........... - Auto
    TRFC0............................... - Auto
    TRFC1............................... - Auto
    TRFC2............................... - Auto
    TRFC3............................... - Auto
    Trdrd............................... - Auto
    TrwtT0.............................. - Auto
    Twrrd............................... - Auto
    Twrwr............................... - Auto
    CS/ODT Pin Fine Delay............... - Enabled
    TLB Cache Mode...................... - Enabled
    Bank Swizzle Mode................... - Enabled
    Auto Tweak Performance.............. - Disabled
    Optimal Performance Mode............ - Disabled
    
    >ODC Control Mode:
    DRAM Drivers Weak Mode.............. - Normal
    Output Drivers Comp................. - Normal
    >Channel A:
    CPU On-die Termination.............. - 300 ohms +/- 20%
    DQS Drive Strength.................. - 1.00x
    Data Drive Strength................. - 1.00x
    MEMCLK Drive Strength............... - 1.00x
    Addr/Cmd Drive Strength............. - 1.50x
    CS/ODT Drive Strength............... - 1.50x
    CKE Drive Strenght.................. - 1.50x
    >Channel B:
    CPU On-die Termination.............. - 300 ohms +/- 20%
    DQS Drive Strength.................. - 1.00x
    Data Drive Strength................. - 1.00x
    MEMCLK Drive Strength............... - 1.00x
    Addr/Cmd Drive Strength............. - 1.50x
    CS/ODT Drive Strength............... - 1.50x
    CKE Drive Strenght.................. - 1.50x
    
    >HT Link Control: 
    HT Link Width......................... - 16 bit
    HT Frequency.......................... - 1.4 GHz (7x)
    IH Flow Control Mode.................. - Disabled
    HT Link Tristate...................... - Disabled
    2x LCLK Mode.......................... - Disabled
    Unit Id Clumping...................... - Disabled
     
    >CPU Feature: 
    CPU DID............................... - 1
    CPU FID............................... - 00 (8x)
    CPU-NB DID............................ - 1
    CPU-NB FID............................ - 03 (7x)
    AMD CPU Stepping...................... - P0
    
    >PWM Settings: 
    PWM Control.......................... - Enabled
    CPU VID Control...................... - 1.30625v
    CPU VID Special Add.................. - Auto
    CPU NB Voltage Control............... - 1.25000v
    CPU NB Vid Special Add............... - Auto
    DRAM Voltage Control................. - 2.12v
    SB PLL 1.2V Voltage.................. - 1.20v
    NB Core Voltage...................... - 1.200v
    NB PCI-E Voltage..................... - 1.120v
    NB HT Voltage........................ - 1.040v
    Last edited by 3oh6; 02-18-2008 at 12:10 PM.
    i don't quote in my signature, but best WR ever...
    Quote Originally Posted by Jor3lBR View Post
    It holds the current WR for the least vcore required to run 4500Mhz stable (1.32vcore)
    i can't even make that shyt up ^^^

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •