ASUS Maximus Formula SE

[cstkl1]

Yes, very easily, see my sig, each of the OCZ, Crucial and Corsair of the PC2-8500 rating I have OC'd on this mobo do 4-4-4-9 quite well. If you're willing to push the vdimm and have good cooling, you can get 1066 @ 4-5-5-10 with the Crucial Ballistics and at least 4-5-5-15 with OCZ XLC.

dude i am asking for memtest 1000 percent stable at TRD 8 or TRD7

can u post ure settings and screenshot...

cause cant seem to do with this motherboard.

oh yeah i have a few team PC2-6400 CL3's , OCZ reapers PC2-8500
and a 500fsb capable proc..
only problem that on this board.. is difficult.

[Nuckin_Futs]

dude i am asking for memtest 1000 percent stable at TRD 8 or TRD7

can u post ure settings and screenshot...

cause cant seem to do with this motherboard.

oh yeah i have a few team PC2-6400 CL3's , OCZ reapers PC2-8500
and a 500fsb capable proc..
only problem that on this board.. is difficult.

CPU Configuration E6750

Ai Overclock Tuner [Manual]
OC From CPU Level Up [Auto]
CPU Ratio Control [Manual]
Ratio CMOS Setting [8x]
FSB Frequency [500MHz]
FSB Strap To North Bridge [Auto]*
PCIE Frequency [111]
DRAM Frequency [Auto]*

DRAM Timing Control [Manual]
Primary Info; 4-4-4-12-3-42-6-3
CAS# Latancy [4]
RAS# To CAS# Delay [4]
RAS# Precharge [4]
RAS# Active Time [12]
RAS# To RAS# Dlay [Auto]
Row Refresh Cycle Time [Auto]

Scondary Info; 8-3-5-4-6-4-6
Read To Write Dely(S/D) [Auto]
Write To Read Delay(S) [Auto]
Write To Read Delay(D) [Auto]
Read To Read(S) [Auto]
Read To Read(D) [Auto]
Write To Write Delay(S) [Auto]
Write To Write Delay(D) [Auto]

DRAM Static Read Control [Enabled]*
Ai Clock Twister [Moderate]*
Transaction Booster [Disabled]*
Relax Level [0]*
------------------------------------------ [CMOS setting] = effective value
CPU Voltage [1.5875v] = 1.568v = 1.576v loaded
CPU PLL Voltage [1.52v = 1.632v
North Bridge Voltage [1.47v] = 1.504v
DRAM Voltage [2.14v] = 2.224v
FSB Termination Voltage [1.40v] = 1.472v
South Bridge Voltage [1.075v] = 1.104v
Loadline Calibration [Enabled]
CPU GTL Refference [0.63%]
North Bridge GTL Reference [0.63%]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [ Auto]
DDR2 Controller REF Voltage [Auto]
SB 1.5v Voltage [1.55v] = 1.584v

CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
-------------------------------
CPU Configuratins:
Virtualization = Disabled*
TM Mode = Enabled
C1E = Enabled
Ex Bit Disable = Enabled*
EIST = (Disabled by BIOS over certain FSB)

This is for the exact E6750 CPU in sig and can be changed to 7x for 3,5GHz by only lowering the vcore and CPU PLL to each

CPU Voltage [1.3875v] = 1.368v
CPU PLL Voltage [1.50v = 1.616v

[cstkl1]

CPU Configuration E6750

Ai Overclock Tuner [Manual]
OC From CPU Level Up [Auto]
CPU Ratio Control [Manual]
Ratio CMOS Setting [8x]
FSB Frequency [500MHz]
FSB Strap To North Bridge [Auto]*
PCIE Frequency [111]
DRAM Frequency [Auto]*

DRAM Timing Control [Manual]
Primary Info; 4-4-4-12-3-42-6-3
CAS# Latancy [4]
RAS# To CAS# Delay [4]
RAS# Precharge [4]
RAS# Active Time [12]
RAS# To RAS# Dlay [Auto]
Row Refresh Cycle Time [Auto]

Scondary Info; 8-3-5-4-6-4-6
Read To Write Dely(S/D) [Auto]
Write To Read Delay(S) [Auto]
Write To Read Delay(D) [Auto]
Read To Read(S) [Auto]
Read To Read(D) [Auto]
Write To Write Delay(S) [Auto]
Write To Write Delay(D) [Auto]

DRAM Static Read Control [Enabled]*
Ai Clock Twister [Moderate]*
Transaction Booster [Disabled]*
Relax Level [0]*
------------------------------------------ [CMOS setting] = effective value
CPU Voltage [1.5875v] = 1.568v = 1.576v loaded
CPU PLL Voltage [1.52v = 1.632v
North Bridge Voltage [1.47v] = 1.504v
DRAM Voltage [2.14v] = 2.224v
FSB Termination Voltage [1.40v] = 1.472v
South Bridge Voltage [1.075v] = 1.104v
Loadline Calibration [Enabled]
CPU GTL Refference [0.63%]
North Bridge GTL Reference [0.63%]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [ Auto]
DDR2 Controller REF Voltage [Auto]
SB 1.5v Voltage [1.55v] = 1.584v

CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
-------------------------------
CPU Configuratins:
Virtualization = Disabled*
TM Mode = Enabled
C1E = Enabled
Ex Bit Disable = Enabled*
EIST = (Disabled by BIOS over certain FSB)

This is for the exact E6750 CPU in sig and can be changed to 7x for 3,5GHz by only lowering the vcore and CPU PLL to each

CPU Voltage [1.3875v] = 1.368v
CPU PLL Voltage [1.50v = 1.616v

dude thats trd 10.
trd 9 is boost enabled
trd 8 is boost enabled 1

example.. i can only do this for about 7-9 minutes

TRD 9 and 10 pass for all day long..
but 8..
hmm and again on P35.. trd 7 was easy.

[Nuckin_Futs]

dude thats trd 10.
trd 9 is boost enabled
trd 8 is boost enabled 1

example.. i can only do this for about 7-9 minutes

TRD 9 and 10 pass for all day long..
but 8..
hmm and again on P35.. trd 7 was easy.

Where do or did you get 10 from. If reffering to Read To Write Delay Time, mine in is 8 when set to AUTO. I forget if it changed on various changes of Clock Twister and or primary timings. I do believe relaxing the Booster effects this but haven't tested into depth.

I have noticed that certain BIOS releases have changed how it is set when in AUTO and with Booster disabled and relaxed to "0"

[cstkl1]

Where do or did you get 10 from. If reffering to Read To Write Delay Time, mine in is 8 when set to AUTO. I forget if it changed on various changes of Clock Twister and or primary timings. I do believe relaxing the Booster effects this but haven't tested into depth.

I have noticed that certain BIOS releases have changed how it is set when in AUTO and with Booster disabled and relaxed to "0"

hmm based on e8400 thats tRD 8... moderate+disabled relax 0.
mistake...argghh cant remember.. wasting my time on this proc with this board..

other mobos can do tRD 7..
heck i didnt try it with the 65nm.. should have.
use memset and u will get the performance value aka tRD..
read anandtech latest x48 review on min trd..



give up need new bios..