started
started
P02 installed, LED now working, and as far as my A0 issue, its still present with reboots.....only certain fsb 1650-1750
Nice setupOriginally Posted by DarthBeavis
started
Exactly what i was thinking about.
No v-mod on the cards as far as i can see?
Is there room for wc on the southbridge with 3 cards installed?
Cant wait to see some results.
Might get me a 3rd gtx or wait for 9800 serie just wait for your benchies.
Last edited by Justifire; 12-27-2007 at 03:39 AM.
QX9650 @ 4450 mhz
Asus Striker II Extreme 790i
4 GB Corsair Dominator 1800 @ 1870 8-8-8-20 1T 1.8v
3 x Asus GTX280 TRI-SLI 810/1647/1296
Asus Xonar DX
Thermaltake Toughpower 1500 W
Dell 30" 3007WFP
Logitech G7, G15, G25
Watercooling Hailea 1500 chiller, EK, Swiftech, D-Tek
Dual Prometeia site
3 cards shouldnt matter. As you can see from that picture only 2, are above the SB.Nice setup
Exactly what i was thinking about.
No v-mod on the cards as far as i can see?
Is there room for wc on the southbridge with 3 cards installed?
Cant wait to see some results.
Might get me a 3rd gtx or wait for 9800 serie just wait for your benchies.
What your trying to say?
That you dont know neither?
I want to know sure or the 2nd card is blocking the way for a sb wc-cooler.
At the moment 1 have an EK sb-block on my 680i between 2 cards in 1st and 3rd slot.
As far as i can see im not so sure if it is possible to keep that in place with a 3rd card installed.
Last edited by Justifire; 12-27-2007 at 03:52 AM.
QX9650 @ 4450 mhz
Asus Striker II Extreme 790i
4 GB Corsair Dominator 1800 @ 1870 8-8-8-20 1T 1.8v
3 x Asus GTX280 TRI-SLI 810/1647/1296
Asus Xonar DX
Thermaltake Toughpower 1500 W
Dell 30" 3007WFP
Logitech G7, G15, G25
Watercooling Hailea 1500 chiller, EK, Swiftech, D-Tek
Dual Prometeia site
Hey all, first post.startedWorking on putting together up my 1st wc box.
DarthBeavis, what are you using to connect your 8800's to each other? I have the EK blocks and the barbs are too long for the 3-way. Should I grab a stubby or two or perhaps give the DD male-to-male nipple a whirl? (Man, that last sentence just doesn't sound right...)
QX9650 | 780i | 3x 8800GTX SLI | 4GB (4x1) TWIN2X2048-9136C5D | 2x RaptorX 150GB | 2x DeskStar 1TB | Z5500 | Galaxy DXX 1000W | U2-UFO | 2407WFP-HC
D-Tek Fuzion | 2x DDC + PTop | 3x EK-FC8800GTX | 2x MCRES | PA120.2 | PA120.3 | 1/2 Tygon
I would do stubbies . . .I found the little play u get with them and tubing makes it easier to get the sli bridge on.Hey all, first post.
DarthBeavis, what are you using to connect your 8800's to each other? I have the EK blocks and the barbs are too long for the 3-way. Should I grab a stubby or two or perhaps give the DD male-to-male nipple a whirl? (Man, that last sentence just doesn't sound right...)
Posting Permissions
Reply With Quote
Bookmarks