Cpu-z 1.40.8

**CHaynes112** · 08-01-2007, 07:23 AM

One problem I have noticed on my (and a buddy's) Turion 64 X2 processors that was present in 1.40.5 and still in 1.40.8 is that the VCore is reported wrong when the CPU is undervolted (for throttling/battery). It reads fine @ 1.075v when running normal, but when I undervolt it to 0.700v, CPU-Z displays 1.425v...

-Thanks

**cpuz** · 08-01-2007, 10:24 AM

Originally Posted by joe.latino

ehm also i have problems with 1.40.8 and vista x64:my pc always crash just running it,why?

ps. with old versions I hant any problems
thanks

Can you please send me a reg dump made with version 1.40.5 ?
Thanks

**joe.latino** · 08-01-2007, 11:42 PM

Originally Posted by cpuz

Can you please send me a reg dump made with version 1.40.5 ?
Thanks

sorry but i dont know how i ought to do it and then tomorrow ill go for vacancy.
i hope there will out a new version for my return! thanks alot...

**cpuz** · 08-02-2007, 01:39 AM

Originally Posted by joe.latino

sorry but i dont know how i ought to do it and then tomorrow ill go for vacancy.
i hope there will out a new version for my return! thanks alot...

OK, you can jsut send me your email in a private message, and I'll send you a test version. THanks !

**cpuz** · 08-02-2007, 01:40 AM

Originally Posted by Kunaak

hey, where did the command rate go?

Do you mean it does not appear anymore ?

**cpuz** · 08-02-2007, 01:42 AM

Originally Posted by Cranox

Reads core voltage wrong here , dumpfile is attached.
Vcore is in bios 1350v , cpu-z says 1.26v

The dump shows two possible values, from two sensor chips.

Code:

Voltage sensor 0	1.26 Volts [0x4F] (CPU VCORE)

and

Code:

Voltage sensor 0	1.31 Volts [0x52] (CPU VCore)

I guess the 2nd one is the correct value ?

**bing** · 08-02-2007, 02:04 AM

Franck,

Any possibility to put the CPU VID in CPUZ ?

**cpuz** · 08-02-2007, 03:09 AM

Originally Posted by bing

Franck,

Any possibility to put the CPU VID in CPUZ ?

Hi,
you can use the ini file to achieve that (use the ini file that is in version 1.40.5 on the web site).
Set sensor to OFF in the ini file, this will force the version 1.40.8 to display the VID instead of the Vcore.

**M3kk** · 08-02-2007, 03:35 AM

Its OK for me

.

**msgclb** · 08-02-2007, 03:55 AM

Originally Posted by cpuz

Do you mean it does not appear anymore ?

It does on a 965P-DS3 but it's blank on my P5K Deluxe.

**Cranox** · 08-02-2007, 11:17 AM

Originally Posted by cpuz

The dump shows two possible values, from two sensor chips.

Code:

Voltage sensor 0	1.26 Volts [0x4F] (CPU VCORE)

and

Code:

Voltage sensor 0	1.31 Volts [0x52] (CPU VCore)

I guess the 2nd one is the correct value ?

No , but CPU-Z 1.39 reads it better cpu-z is jumping between 1.319v - 1.328v ( measered 1.346v , biossetting 1.350v )
I got a dumpfile attached.

**trans am** · 08-03-2007, 05:56 AM

Thank you DR. CPUZ
p5k and xeon 3060 working great!

**msgclb** · 08-11-2007, 11:10 AM

I just recently noticed the following CPU-Z Version 1.40.8 behavior concerning Command Rate using my P5K Deluxe.

Here I don't have Command Rate...

Click image for larger version.

Name: CPU-Z-1.40.8.jpg
Views: 355
Size: 154.5 KB
ID: 62785

But as soon as I open MemSet...

Click image for larger version.

Name: CPU-Z-1.40.8-MemSet.jpg
Views: 339
Size: 137.9 KB
ID: 62786

**M3kk** · 08-11-2007, 11:12 AM

1.40.9 http://www.cpuid.com/beta/cpuz.zip

**msgclb** · 08-11-2007, 11:27 AM

Thanks for the 1.40.9.

Same behavior...

Click image for larger version.

Name: CPU-Z-1.40.9.jpg
Views: 312
Size: 154.0 KB
ID: 62787

When I ran MemSet the Command Rate appeared.

**doakh** · 08-11-2007, 11:39 AM

Installed 1.40.9 in Vista64 and it shows the correct voltage.
Well Done!

HAPPY MOTORING!!

**mascaras** · 08-11-2007, 01:59 PM

Originally Posted by M3kk

1.40.9 http://www.cpuid.com/beta/cpuz.zip

1.40.9 already posted in 1st page :

Originally Posted by cpuz

I spoke too fast.
This should work this time.
http://www.cpuid.com/beta/cpuz.zip

btw: works fine here

**Infa** · 08-11-2007, 02:32 PM

vcore fine for me to

thanks!

**Baron** · 08-11-2007, 02:54 PM

Works fine here.

Oh wait no it doesnt.

1.7V you having a laugh!?!

**Eastcoasthandle** · 08-11-2007, 04:29 PM

**cpuz** · 08-12-2007, 01:41 AM

Originally Posted by Baron

Works fine here.

Oh wait no it doesnt.

1.7V you having a laugh!?!

Oh well ...
Can you please send me a register dump, or post it here ?
Thanks

**jimmyz** · 08-12-2007, 01:59 AM

1.40.9 cause a lock-up on my system. dfi r600 with e6600 2gb ballistix? downloaded twice both either cause reboot or lock-up?

**cpuz** · 08-12-2007, 02:09 AM

Originally Posted by jimmyz

1.40.9 cause a lock-up on my system. dfi r600 with e6600 2gb ballistix? downloaded twice both either cause reboot or lock-up?

Can you please set sensor=OFF in the ini file and try again ?
If this works, please save a reg dump and send it to me.
If this keeps locking-up, please send me a PM.

Thanks !

**Don_Dan** · 08-12-2007, 02:15 AM

I have come across a very strange problem when using pcprobe2 und cpu-z 1.40.9. I never had this problem when using older versions, but it also appeared when using 1.40.8. BTW, voltage isn't correct, too. Is this a known problem?