My mounting kit

[Marvin]

Duniek, what is the difference between rev 2.0 and 2.5 ?
regards,
Marvin

[Duniek]

only diffrent with 2.0 and 2.5 is in evap

evap 2.0 has enter capilary on top and suction center on bottom

evap2.5 has enter capilary on bottom center
so whole cap tube is in suction

[Duniek]

project
instead 4mm I drill 2,9mm hole


and 2,3mm chaneles and 1,7mm gaps

[jinu117]

project
instead 4mm I drill 2,9mm hole


and 2,3mm chaneles and 1,7mm gaps

Make the bottom about 1 mm thinner to make it do a little better And at the top, make it bit smaller on drill size and just nick it with suction tube OD size so you can push it in without having to worry about blocking suction return...
This one really brings me back old memories lol.

[Duniek]

Make the bottom about 1 mm thinner to make it do a little better And at the top, make it bit smaller on drill size and just nick it with suction tube OD size so you can push it in without having to worry about blocking suction return...
This one really brings me back old memories lol.

can do captain
in next revision will be done

[LittleDevil]

Really nice, but those sprngs are little too weak for SS mounting i think

regards

[Pete]

Yay your putting some insuatlion around the otuside of the muff. I save 10c on the vapo LS doing it my self.

I might have to get one of these new ones off you dude

[Freddie123]

I would definately make the base thinner. 6mm is pretty thick. I would personally go to 4mm tbh

[Duniek]

this evap good hold quad
but I will make 4 and 5 mm base for test after new year

btw

[Duniek]

during making foam for rev2.0 enclousure

//
extras for rev2.0 enclousure

[Pete]

Really impressive stuff Duniek. Can't wait to get my toys and get them built up

[Duniek]

custom ones

[Duniek]

multi mounting for vapo XE/SE evap

[peterpiper]

multi mounting for vapo XE/SE evap

Cheers Duniek,
Arrived during the week. It's a pity the Vapochill performance doesn't do your work justice. Nice Job!

Initial play, holds an E2160 @ 3.4, and that's about it!

[Duniek]

I made big gallery in first post

so enjoy with it

regards

[Mphs]

@ Duniek, nice works man!

[Duniek]

new gpu mounitng

[Pete]

F******* about time these come in don't ya think? Was last year when we talked about them. Mind i know you had machinest issues. Looking good non the less

[kipow]

Nice work, please send me a PM with your prices for LGA 775 evap and monting kit.

[Duniek]

F******* about time these come in don't ya think? Was last year when we talked about them. Mind i know you had machinest issues. Looking good non the less

cpu kit in progress to

btw
laser cut backplate insulation

[Nosfer@tu]

cpu kit in progress to

btw
laser cut backplate insulation

Looks GOLDEN m8

Setting a new standard

[LittleDevil]

Really nice, but i can tell you that that isulation is not enough thick and strong for backplate (motherboard isulation). Try to mount it and you will see in 1 week how thick it will be

Kind Regards

[n00b 0f l337]

Not so much about thickness as an air tight seal at least for me. But yeah that would probably compress pretty heavily. You'd end up having to tighten down again.

[Duniek]

130 backplates on stock

[n00b 0f l337]

PM me Duniek, maybe its time I deal with shipping cost to you