FX Meets DI - First Run

[babyelf]

DFI NF4 Ultra-D
FX57 CABCE 0516 WPMW
Antec 550W TruePower2.0
2 x Raptors
Corsair 3200LLv1.1 | OCZ GX | TEAM BH-5
Chilly1 DI Container
Liquid Electrical Tape
Acetone
Funnel
Neoprene Tape






Insulation : (listed by steps)

Liquid Electrical Tape around socket
- Liquid Electrical Tape will take approximately 20-30minutes to dry depending on how thick you apply on the motherboard. It will peel off easily from your motherboard so don't worry.




Neoprene Tape on Liquid Electrical Tape and gaps taped up with electrical tape and holes covered by Liquid Electrical Tape
- Next use some neoprene tape on the liquid electrical tape for extra insulation and for the extra height for better contact with the cylinder neoprene piece.
- Tape some neoprene on the back as well just in case.
- Cover the gaps with electrical tape






Test Mount




Dry Ice Run
- Best run for me is about 50ml of Acetone then some crushed ice followed by normal dry ice pieces.





1M


8M


32M


After Run
- What I do is i remove all cylinder neoprene and then pour out all dry ice from the container.
- After that I add water into the container to warm the container so that the bond between the container and processor will loosen and then give it a good twist and it will come off easily.








I have about half an eski of DI left.. will be doing more benching again tomorrow

2nd day :

first bad mount and ran out of ceramique.. tried AS5 and it didn't work well so had to cancel subsequent runs

had some dry ice left so i had some fun with them


Removing Insulation

[bachus_anonym]

Nice 32M time, babyelf Don't forget to submit it on Holicho's Ranking

Gotta love that liquid electrical tape, eh? That stuff is just a must-have for phase change and DI/LN2 runs...

Congrats on a successful session

[Athens[2004]]

Nice !! Very Nice insulation & pretty Good Benches 2

[babyelf]

Nice 32M time, babyelf Don't forget to submit it on Holicho's Ranking

Gotta love that liquid electrical tape, eh? That stuff is just a must-have for phase change and DI/LN2 runs...

Congrats on a successful session

thanks alot

one more session to go tomorrow

yea lol.. started using it then i couldn't stop lol.. just had to brush it everywhere

]Nice !! Very Nice insulation & pretty Good Benches 2

thanks

[waddupmm]

Pics dont work any more?

[babyelf]

just refresh a couple of times.. hosting went a bit crazy today

[babyelf]

3602.5Mhz

257.3 x 14

[metro.cl]

nice runs and nice insulation

[babyelf]

yeah got pics working now nice runs M8

thanks MM

nice runs and nice insulation

thanks

One Q before i start today tho.. how much Acetone is needed in the container?

After running for a while the temps went back up to 0c or so in bios so i took it apart and there's no condensation.. then i checked and realised there's no more acetone left..

[afireinside]

Not sure about the chilly1 container but a shot glass works best. I've seen using a medicine cup filled to the top lately. I doubt thats enough for the chilly1 tube, though.

[babyelf]

ic.. thanks for the tips.. going to start now.. will try pouring about 50ml first and see how the temps go

[babyelf]

first mount bad... then tried to remount but ran out of ceramique so i tried AS5.. and temps were horrible..

so much for benching today..

[T_M]

no pics for me
find another host maybe

[[XC] moddolicous]

I think people use AS Ceramique for subzero benches, not AS5. Looks really good.
Some timings to try for SPI 1m:
Tref: either 4708 or 3684
tras: 3
TRC: 5
Async latency: 7ns
read preamble: 5.5 or 5ns

[\Karting_freak]

impressive!

[kiwi]

Yeah, I like that neat insulation as well and nice scores
Does that Liquid Electrical Tape come off easily or not?

[babyelf]

no pics for me
find another host maybe

yea looking for one at the moment

I think people use AS Ceramique for subzero benches, not AS5. Looks really good.
Some timings to try for SPI 1m:
Tref: either 4708 or 3864
tras: 3
TRC: 5
Async latency: 7ns
read preamble: 5.5 or 5ns

yea.. ran out of it that's y 2nd day didn't go well..

thanks for the tips.. ceramique coming soon and might find another day to do it

impressive!

thanks

Yeah, I like that neat insulation as well and nice scores
Does that Liquid Electrical Tape come off easily or not?

pics coming under next reply

[babyelf]

had some DI left after that.. so was playing with it lol

[dinos22]

holy baby you're are killing it over there.....extremely nice 32M speeds.......man with some more tweaking OPB watch out

[babyelf]

ta dinos.. OPB is called OPB for a reason u know?

[dinos22]

ta dinos.. OPB is called OPB for a reason u know?

hold no prisoners....there was someone there before OPB too......this is XS afterall......hehehhe

good luck anyways...looking good

[SLi_dog]

Hi babyelf,
Nice setup and PI times.
How much did the Chilly1 DI/LN2 tube cost?

[babyelf]

ta

got it on for sale here.. pm chilly1 for the price of the new container

[nachthymnen]

Incredible!!!You have obtained exactly my same time in 1M:

[babyelf]

Incredible!!!You have obtained exactly my same time in 1M:

lol nice lol

on DI too?