Help me to design my Watercooling in Antec P182.!

[manyga]

I will put:

-Cpu: D-Tek Fuzion

-Vga's: 2 x EK EK-FC88 GT/GTS (G92) ACETAL SLI READY

-Pump: Laing D5

-Radiator: BLACK ICE GTS 360 and 3 Antec Tricool.

-Reservoir: unsettled...Ideas??





Could you help me to decide distribution, colocation of pump, reservoir, radiator... and toube route??

You can paint in the pics your ideas!!

Thanks you so much!

[manyga]

Any idea?

[Eddie3dfx]

There was a thread on here the other day with a great p182 that looked very clean

[Giannis86]

maybe something like this?


personally i would go with the DDC3.2+XSPC restop...less tubes required for that & it should provide more flow given you are aiming for a multiblock system

[manyga]

Thaks for the picture bro!!

But the DDC3.2 have low pressure, no? I think that D5 is more powerful and more flow.

I prefer the radiator in the back!

Thanks and You continue drawing!!!!

[Waterlogged]

Thaks for the picture bro!!

But the DDC3.2 have low pressure, no? I think that D5 is more powerful and more flow.

I prefer the radiator in the back!

Thanks and You continue drawing!!!!

This is only true if you compare a DDC 3.1 to the D5. The DDC 3.2 is stronger than the D5 though, just check max head.

[Giannis86]

its better with a custom top though. the XSPC res top was a top performer as tested by Martin

how about this then ?

or

[Xel'Naga]

I it like all internal



EDIT: Can you see the pic? Sometime I do, sometimes I don't even though the page finished loading

[TRG]

P182 / P180 in combination with a big loop and big rad is a nightmare. It's doable, but you'll end up with your rad outside or losing harddrives if you use more than four of them..

I've personally changed from P180 tot Stacker 101 cause of this problem. It's doable, but you'll have to make concessions when you use lot's of hardware..

[manyga]

Nice!!!!

I don't have space in the interior to place the radiator!

[manyga]

I it like all internal



EDIT: Can you see the pic? Sometime I do, sometimes I don't even though the page finished loading

You have seen pics with PSU there?

Where I can buy DDC 3.2 + XSPC restop in europe?

I'm from Spain!

Thanks so much!

[Giannis86]

This is what works best for me (qua lowest prices etc)..But this is mainly cause i will be getting many parts from petras anyway so the sending cost will be less for each individual part i suppose


XSPC Laing DDC Top/w Reservoir
IT-Service.be (Belgium) € 23,75

Laing DDC-3.2 (18W)/Swiftech MCP355 Inline 12V DC Pump
Petra's Tech Shop (America..i figured it would be cheaper like that, for me at least) $74,99


The xspc restop is not to be found at many stores..it is available in england though (Aqua PC's) which is close to Europe i suppose)
http://www.aqua-pcs.co.uk/xspc-laing...oir-1240-p.asp

[perfection]

I it like all internal



EDIT: Can you see the pic? Sometime I do, sometimes I don't even though the page finished loading

a standard ATX PSU will fit sideways in the bottom compartment like the Silverstone TJ07, allowing you to have 2-3 inches for the radiator.

[[XC] NetburstXE]

Sorry to threadjack, but how much better is the DDC3.2 than the D5?

[Giannis86]

i know there was a thread on this but couldnt be bothered to find it..here is a graph using the data in martins flow estimator



ps if it cant be seen clear
red: DDC3.2 +XSPC restop
blue: DDC3.2 stock
purple: D5 Setting 5 (24V)

[skid9uk]

i did mine like this http://www.xtremesystems.org/forums/...60#post2694360 look for the one by skid9uk

[manyga]

finally I will put Laing D5 because ddc3.2 I can't buy it in spain...

[vblanche]

Where I can buy DDC 3.2 + XSPC restop in europe?

http://specialtech.co.uk/spshop/cust...cat=840&page=1