3000+ Venice: 3194MHz Pifast || Budget ocing!

[Epsilon]

Done on custom phase-change

http://valid.x86-secret.com/show_oc?id=19647






On this single stage home made phase change



Score on boxed air:



max screenshot : around 3300mhz, will post tomorrow.

Need a new install, the NF4 drivers arent installed yet, only NF3 drivers. Will gain another 0.4sec or something

Other specs:

- DFI NF4 Ultra-D
- 2x256MB Mushkin old bh-5 (level2)
- PCP&C 510w sli psu
- 120GB WD 7200RPM (like it matters)
- FX5200 PCI

[Micutzu]

Very nice! What was the evap temp at CPU idle ?

[Mahoney]

Nice oc epsilon.!

What about the week and stepp??

[Toki]

Awesome result

And yeah, we want to know step and week

[Epsilon]

Very nice! What was the evap temp at CPU idle ?

The evap temp (on the block) varied from -48c to -38 (depending on speed and voltage) .

That's in the very bottom of the block, so infact the CPU temp. -22c in bios btw .

Stepping:

CBBLE 0512 DPBW
xxxx0217

[Keelz]

awesome result

[Jort]

budgetoverclocking is cool

is just like the winnie's but these are even better

[mion]

nice, what are your temps

[Epsilon]

Maybe I will suicide shot today

Temps in the bottom of the evap vary from -48c idle @ 2800mhz 1.4v to -38c idle @ 3194 1.7v. Loaded the temps rise to -30c in the bottom of the evap block.

The sensor is here:


And not on the suction as the Mach2 GT etc. The loaded temps at 3194/1.7v are -42c on the suction line

[Epsilon]

And a suicide screenshot @ 3419mhz

http://valid.x86-secret.com/show_oc?id=19647

[don_vercetti]

quality graphics card! That is PCI i take it? What is it?

Very good speeds btw, maybe a bit of burn in will help it go even higher? How long have you had it for?

[Epsilon]

It is brand new, this is after just 5hours of running both air and phase-change

It is FX5200 128MB PCI videocard
I use it for CPU benches because it practically doesn't take power so CPU has all

[don_vercetti]

well a bit or burn in probably won't hurt then, i know it's physically incorrect at all, but it does seem to work, loads of people have noticed it.

[Epsilon]

just wait and the CPU will go faster probably

[Epsilon]

CPU will be sold

THis is the final result:

[piotres]

Wow ! Nice score Epsilon ...


Please write more informations about Phase-change- what compressor, what gas ???

peter

[NiCKE^]

Isnt that a WR? If it's post it in the WR thread.

[V4n{}u|sH]

Great job and great CPU

[cpulloverclock]

nice

which step?

I receive my 0517 DPMW wednesday


coolaler can bench at 3.41G with his 3000+

[Shadowmage]

lol, phase change isn't budget OCing

GJ tho

[HiJon89]

lol, phase change isn't budget OCing

GJ tho

Its "custom phase-change" which means the whole thing probably didn't cost more than $500, not exactly budget, but not exactly the high price you think of for phase change cooling

[[XC] moddolicous]

Nice scores. I think with some tweaking and a little higher OC, 36sec in PIfast would have been possible.

[Epsilon]

maybe it was possible, but I have to lap my evap first, contact wasn't 100%.

The thread of my cooling systems is over @ teampuss

Here is the thread:
http://www.teampuss.com/forums/viewtopic.php?t=605

But, because you have to register to view, I will post some specs here

It's a 14cc 1/2hp R404a compressor
runs with 3meter 0.031" captube
Propane as refridgerant
and chilly1 evap

idle @ -57c
Loaded with 180w @ -42c on the suction line (were prommy's are meassured)
-30c in the very bottom of the block @ load.

[404Power]

HOLY SH*T!
I don't know what to say.....

AWESOME RESULTS Epsilon!

[Zyklon5]

Nice setup you got there ! congrats ! How did your Venice do on air maybe with a better week you could go higher.