Vdimm/Vcore mod for MSI K8N Neo2 PLatinum-54G Edition S939

**I(illa Bee** · 02-03-2005, 04:26 PM

Originally Posted by GravediggA

Sweet, thanks big time dude, i just mesured mine, im 1.62v...heres the thing, my BIOS is set to 1.55v with + 10%....so thats the highest this board will go, thats not too high for a 90nm core is it? what voltage do other 90nm users use?

since its 1.4v stock.. my temps look good an its runn good..

**_zZz_** · 02-08-2005, 03:59 AM

For "normal" overclockers... is it safe to do the vdimm like this?

what are the differences for pc_ice way?

thanks a lot
_zZz_

**adslegend** · 02-08-2005, 05:31 AM

Originally Posted by GravediggA

Hi, I'm currently running a Winchester 3000+ at 295x9. BIOS is set to 1.55V+10%, CPU-Z says about 1.61-1.63V under load but I'm reading 1.39V idle and 1.35V load from that mosfet!

It's semi-stable at this speed, I can play CS:Source indefinitely but Superpi fails 32M test after about 6 minutes. Is the Vcore really that low?

[Edit] One more thing, using clockgen I can set the VID to anything equal to or below 1.45V but anything higher (goes up to 1.55V) and it just stays at 1.45V. Strange.

**I(illa Bee** · 02-08-2005, 07:09 AM

Originally Posted by _zZz_

For "normal" overclockers... is it safe to do the vdimm like this?

what are the differences for pc_ice way?

thanks a lot
_zZz_

that just makes it 3.3v right? I was thinking of getting a DDR booster but my memory like 3.0v, (TCCD) so i was thinking ill try a 3.3v mod and see if it likes that, if it dose ill go with it.

**_zZz_** · 02-08-2005, 07:11 AM

it makes Vdimm = Vio.. so u can change the 3.3v line of the power supply...

_zZz_

**I(illa Bee** · 02-08-2005, 07:13 AM

Originally Posted by _zZz_

it makes Vdimm = Vio.. so u can change the 3.3v line of the power supply...

_zZz_

what do you mean you can change the PSU 3.3v line? Your talking about a sence wire mod right? Not in the bios?

**arctic-k20** · 02-11-2005, 06:17 AM

if your psu has pots on each rail like the ocz powerstream psu's - or if you install the pots your self

**I(illa Bee** · 02-11-2005, 08:33 AM

ohh ok, yea my PSU has pots, i put them there myslef

I jsut didnt understand what you were sayin..

**scifikg** · 02-11-2005, 09:35 AM

For the VDD mod, there are 2 solder pads for both the red and brown wires. Do I solder the wires to the pads closest to the SATA ports or do I need to bridge the solder pads and attach the wires. It is hard to tell from the picture.

**Barr3l Rid3r** · 02-13-2005, 12:34 PM

Originally Posted by ilgreco1974

THANKS!
If you set it higher than 1.75 you wil get more than 10mhz in htt?There is a safe max voltage limit?

probably not

**Giana** · 03-09-2005, 12:31 PM

Hi out there .... Have a question about the Vdimm mod for the K8N Neo 2

Here we can see the default mod ...

And here You can see the Mod for the MSI K8T Neo2-F done for a friend of my.

U can see, i soldered direktly to the RamSlots. Will this work for the K8N Neo2 too, or have I to use the Capa Mod ?

**_zZz_** · 03-09-2005, 02:21 PM

i've done the one on the first picture and it works great

**Giana** · 03-09-2005, 11:44 PM

One other question ... i have read the K8N Neo2 tips and tricks guide .... there is an informnation wich is telling me the OCZ Booster will work to 4V on Slot 4

The OCZ Homepage just tells me the Booster will only work to 3.4V for this Board.

Wich information is correct ?!?

**_zZz_** · 03-10-2005, 12:04 AM

the one here of course :P

this board tracks the vtt correctly,so theres no problem on it

_zZz_

**Barr3l Rid3r** · 03-16-2005, 05:46 AM

I've got 2 questions:

1) Pot for VDD mod should be 20k right? To increase voltage I need to lower the resistance?
2) Can I use JC11 (chassis intrusion jumper) to plug my 3.3V vio mod on it? So I can turn it on and off.... using a jumper

**kasius** · 03-18-2005, 02:10 AM

Originally Posted by adslegend

Hi, I'm currently running a Winchester 3000+ at 295x9. BIOS is set to 1.55V+10%, CPU-Z says about 1.61-1.63V under load but I'm reading 1.39V idle and 1.35V load from that mosfet!

It's semi-stable at this speed, I can play CS:Source indefinitely but Superpi fails 32M test after about 6 minutes. Is the Vcore really that low?

[Edit] One more thing, using clockgen I can set the VID to anything equal to or below 1.45V but anything higher (goes up to 1.55V) and it just stays at 1.45V. Strange.

Hi everybody:
My first post

(from Spain)

I get same problem that adslegend, CPU-Z says 1.600 and mosfet read 1.39 idle and 1.35 load. If I put 1.40 bios and CPU-Z says 1.400-1.39, mosfet read is 1.20

. Is posible that reading point of vcore was other point, what??

Thanks

**Zebba** · 03-21-2005, 09:57 AM

Hey ! Is there anyone out there who have made this mod on a MSI K8TNeo2 -F ?

**Zebba** · 03-21-2005, 02:01 PM

Or any simple guide to do a vdimm mod on a MSI K8T Neo2 -F

**raydelee** · 03-25-2005, 09:04 AM

may i know how to get vdimm reading on multimeter for MSI K8N NE0 2?

thx

**funkflix** · 03-25-2005, 09:20 AM

Maybe u should try to read the Thread ....

**raydelee** · 03-25-2005, 10:12 AM

it is the JC11 on the picture measuring point for Vdd
both multimeter probe on the pins or red on the either one & black probe on casing

thx

**funkflix** · 03-25-2005, 10:17 AM

Red on the green Point Black on Case or any other Ground.

**raydelee** · 03-25-2005, 10:50 AM

thanks bro...

**Barr3l Rid3r** · 03-27-2005, 11:20 AM

Direct mod on/off

And what I could get from that

**kasius** · 04-01-2005, 03:18 AM

Definitely, what is the reading VCORE point?? IÂ´m confused. Some pic?

Bye

Thread: Vdimm/Vcore mod for MSI K8N Neo2 PLatinum-54G Edition S939

Thread Tools

Search Thread

Rate This Thread

Display

Bookmarks

Bookmarks

Posting Permissions