try "100 1/2" the first option
try "100 1/2" the first option
Everything extra is bad!
It's all about finding the boards max.Originally Posted by p4z1f1st
Imagine one could find mem that does 400MHz....
And like Ubermann says, it was fun!
Asus Crosshair V Formula-Z | FX 8350 | 2x4GB Trident-X 2600 C10 | 2x ATI HD5870 Crossfire | Enermax Revo 1050watt | OCZ Vertex 3 60GB | Samsung F1 1TB
Watercooling: XSPC Raystorm | EK 5870 Delrin fullcover | TFC X-changer 480 w/ 4x Gentle Typhoon | DDC2+ Delrin top | EK 200mm res | Primochill LRT 3/8 tubing
Case: Murdermodded TJ-07
sub 9 sec. SPi1M 940BE 955BE 965BE 1090T
Good job man...I shall try 420 as well...I have yet to try that...I will try it tonight
Ubermann add me to your message list Yahoo! or AIM
heyz
with 5x multi PC don´t boot (error "Detecting array")
man...i think, i've got the worst Board ever produced by DFI....it even won't make a HTT of 300MHz !!!!
i even set EVERYTHING @ timings on AUTO except of the divider (1/2)....FSB set @ 300MHz with 1/2-divider = DRAM-frequency of 150MHz....
mutli set @ 6.....i even won't boot-up clear.....it craps out at the drive-detection-screen in the beginning and hangs up.....
what to do?
----- AMD K6-2 300 "Chomper" xxxxx xxxx xxxx /// 300 MHz @ 2,200 V -----
----- AMD Athlon XP 1700+ "Thouroghbred B" JIUHB 0306 MPMW /// 2400 MHz @ 1,900 V -----
----- AMD Athlon XP-M 2500+ "Barton" AQXEA 0327 UPMW /// 2450 MHz @ 1,850 V -----
----- AMD Athlon XP-M 2600+ "Barton" IQYHA 0401 XPMW /// 2500 MHz @ 1,750 V -----
----- AMD Athlon 64 3000+ "Newcastle CG" xxxxx 0418 WPMW /// 2600 MHz @ 1,600 V -----
----- AMD Athlon 64 3200+ "Winchester D0" xxxxx 0433 SPMW /// 2750 MHz @ 1,616 V -----
----- AMD Phenom II X2 555 BE "Callisto" xxxxx xxxx xxxx /// 4080MHz @ 1,375 V -----
----- AMD Ryzen "Zen" xxxxx xxxx xxxx /// TBA @ TBA -----
Get yourself a ClawHammer.Originally Posted by p4z1f1st
All 400+ results are ClawHammers.
Asus Crosshair V Formula-Z | FX 8350 | 2x4GB Trident-X 2600 C10 | 2x ATI HD5870 Crossfire | Enermax Revo 1050watt | OCZ Vertex 3 60GB | Samsung F1 1TB
Watercooling: XSPC Raystorm | EK 5870 Delrin fullcover | TFC X-changer 480 w/ 4x Gentle Typhoon | DDC2+ Delrin top | EK 200mm res | Primochill LRT 3/8 tubing
Case: Murdermodded TJ-07
sub 9 sec. SPi1M 940BE 955BE 965BE 1090T
Do you run "command per clock" disable ?
Enabled and you get real good bandwidth but very unstable over 300FSB.
Disabled and you can run pretty much anything out of this world.
I noticed (maybe already posted here)
With 2T you can run Drive strength level 4
With 1T you must run level 1 (max 2)
Correct me if im wrong about this plz.
Last edited by Ubermann; 09-22-2004 at 12:55 PM.
Everything extra is bad!
hmm....kk, i only runned with 1T....
so, ubermann, i'm running always with level4....thought, it would be the "relaxed" of all 4 options....
hmm...kk, i'll try again....
----- AMD K6-2 300 "Chomper" xxxxx xxxx xxxx /// 300 MHz @ 2,200 V -----
----- AMD Athlon XP 1700+ "Thouroghbred B" JIUHB 0306 MPMW /// 2400 MHz @ 1,900 V -----
----- AMD Athlon XP-M 2500+ "Barton" AQXEA 0327 UPMW /// 2450 MHz @ 1,850 V -----
----- AMD Athlon XP-M 2600+ "Barton" IQYHA 0401 XPMW /// 2500 MHz @ 1,750 V -----
----- AMD Athlon 64 3000+ "Newcastle CG" xxxxx 0418 WPMW /// 2600 MHz @ 1,600 V -----
----- AMD Athlon 64 3200+ "Winchester D0" xxxxx 0433 SPMW /// 2750 MHz @ 1,616 V -----
----- AMD Phenom II X2 555 BE "Callisto" xxxxx xxxx xxxx /// 4080MHz @ 1,375 V -----
----- AMD Ryzen "Zen" xxxxx xxxx xxxx /// TBA @ TBA -----
ok, i give ti up.....i tried everything, but it just hangs up in the same screen (drive-detection-screen)......
so, then i tried to drive my EBs with CPC-off qith 270MHz @ memtest.....hangs up.....now i really don't know, what me holding back....my CPU? my board? my RAM?
it just CAN'T BE, that all 3 items have they limit at the same point!
it just CAN'T BE! what for a fu*king random that has to be?!?!
now i'm getting frustated
just don't know, what's holding back
----- AMD K6-2 300 "Chomper" xxxxx xxxx xxxx /// 300 MHz @ 2,200 V -----
----- AMD Athlon XP 1700+ "Thouroghbred B" JIUHB 0306 MPMW /// 2400 MHz @ 1,900 V -----
----- AMD Athlon XP-M 2500+ "Barton" AQXEA 0327 UPMW /// 2450 MHz @ 1,850 V -----
----- AMD Athlon XP-M 2600+ "Barton" IQYHA 0401 XPMW /// 2500 MHz @ 1,750 V -----
----- AMD Athlon 64 3000+ "Newcastle CG" xxxxx 0418 WPMW /// 2600 MHz @ 1,600 V -----
----- AMD Athlon 64 3200+ "Winchester D0" xxxxx 0433 SPMW /// 2750 MHz @ 1,616 V -----
----- AMD Phenom II X2 555 BE "Callisto" xxxxx xxxx xxxx /// 4080MHz @ 1,375 V -----
----- AMD Ryzen "Zen" xxxxx xxxx xxxx /// TBA @ TBA -----
Can it be SATA ?
I use IDE and so does ugp and zeus from what i can see.
Everything extra is bad!
hmmmm........could it be?
...oh man, damn it all
@ bigtoe: did/do you use IDE or sATA? (what drive did you use for the 425MHz-HTT-record?)
Last edited by p4z1f1st; 09-22-2004 at 02:06 PM.
----- AMD K6-2 300 "Chomper" xxxxx xxxx xxxx /// 300 MHz @ 2,200 V -----
----- AMD Athlon XP 1700+ "Thouroghbred B" JIUHB 0306 MPMW /// 2400 MHz @ 1,900 V -----
----- AMD Athlon XP-M 2500+ "Barton" AQXEA 0327 UPMW /// 2450 MHz @ 1,850 V -----
----- AMD Athlon XP-M 2600+ "Barton" IQYHA 0401 XPMW /// 2500 MHz @ 1,750 V -----
----- AMD Athlon 64 3000+ "Newcastle CG" xxxxx 0418 WPMW /// 2600 MHz @ 1,600 V -----
----- AMD Athlon 64 3200+ "Winchester D0" xxxxx 0433 SPMW /// 2750 MHz @ 1,616 V -----
----- AMD Phenom II X2 555 BE "Callisto" xxxxx xxxx xxxx /// 4080MHz @ 1,375 V -----
----- AMD Ryzen "Zen" xxxxx xxxx xxxx /// TBA @ TBA -----
I see a drive detection screen sometimes, after making changes in the BIOS. Just let it go a minute, and it'll hit the normal boot screen.
"I got a fever, and the only prescription, is MORE COWBELL" **I can't afford a sig, all my money's in hardware.**
I shall try some new settings and see what I get and then I will post back
And yes I have an IDE drive... I want two new SATA in a RAID 0
Welp, I swapped out the mobile 3000+ for the DTR 3200+. I can get good clocks with low temps, but it takes a lot of voltage. I'm using 1.613v, I think, (fluctuates in CPUZ) for 2.5 GHz., and the chips only 27C. I about had 2.6 GHz., but when I got to 1.7-something, I chickened out, lol. What do you guys think, should I play it safe, and call 2.5 good, or go for it, since the temps are good? This is just good air BTW, no vapo or prommie.
"I got a fever, and the only prescription, is MORE COWBELL" **I can't afford a sig, all my money's in hardware.**
That isn't that high of voltage. On air it isn't recommend to go any higher than v1.8. That temp is very good, I would go for it man. I would give anything to hit 2.5GHz right now. What settings where you using and what memory do you have?
Usin' 2x512s of Mushkin LII 3500, @ 5-2-2-2-1t. I've had the RAM to 240 @ 3.3v, but the chip does much better using the 5/6 divider. Kinda of a trade off, @250 5/6, the RAM's only doing 208. If they recommend 1.8v tops, then it's probly good for 1.9v or 2.0v, dontcha think?
"I got a fever, and the only prescription, is MORE COWBELL" **I can't afford a sig, all my money's in hardware.**
Originally Posted by spaceman
Go for it. I am setting on 2550 Prime stable with 1.85v with bad air. I know she will go 26xx with some cooling. The DTRs have turned out to be my best clockers & I have mobils,desktops both N/C & C/H , & DTRs. All are 3200 CGs Except the N/C 3400. The DTRs are the only 1m CPU I can get over 2500 Stable with my cooling. I have made it to windows at 27xx. Love to atleast have some water on it. My 3400 N/C only goes 2580 prime stable.
Jess1313
Last edited by jess1313; 09-22-2004 at 08:37 PM.
DFI NF3-250 LanParty UT A64 3200 1m DTR @2550(10x255) - mushkin 222 -3dmark01 - 26424
Shuttle SN85G4 V2 - A64 3200 1m @2525(10x252) - mushkin 222- 9800pro -3Dmark01 - 26379
DFI Ultra B - 2600+ Mobile@2604(10.5x248) - mushkin 222 - 9800pro - 3Dmark01 - 21445
Abit NF7 - 2600+Mobile@2520(10.5x240) - mushkin 222- 9800pro- 3Dmark01 - 21166.
DFI P5BV3+ - K6-III+ 450@600(6x100)@2.4 vcore - Ati 8500 - 2x 4gb Quantan FireBall
*DFI NF3-250GB UT Beta Bioses w/ 4.0vdimm and works w/ mobiles*
*NF7 modded BIOS Vault*
*If you have a DFI NFII MoBo read this*
Welp, 2600 MHz. won't happen here, I even got nutty enough to try 1.968vcore. However, I got 2550 MHz. 3DMarkable, and broke 29k!! Enough for the bottom of the 1st page if you type in Athlon & XT PE. http://service.futuremark.com/compare?2k1=8135079 Doin' it with 1.65vcore @ 26C in the BIOS.
"I got a fever, and the only prescription, is MORE COWBELL" **I can't afford a sig, all my money's in hardware.**
I used an IDE HDD for the 425 run and have used an SATA HDD on my retail board and hit 425HTT again...thing is both boards won't do 1HTT more for me as they are stock with good air cooling.
Got a problem with your OCZ product....?
Have a look over here
Tony AKA BigToe
Tuning PC's for speed...Run whats fast, not what you think is fast
I'll be finally joining in on this DFI fun tomorrow. GameVe, shipped monday, I ordered 3 of the 754 250gb boards. Finally they will be here and more memory volts!!!
Dont even ask where i've been!!!
k used 1:2 divider with 1x 512MB Kingston KHX3200/512 BH-5 week 27, 2003 stick of ram @ 2-2-2-6 1T and managed with AMD64 3400+ Newcastle 372HTT with LDT at AUTO and rest of mem settings at AUTOOriginally Posted by Ubermann
sandra reports AUTO LDT set it as 2.5x LDT so 930mhz hypertransport speed
---
Nice numbers, but just numbers. No real benefit from these settings.Originally Posted by eva2000
I´d be impressed by high "1:1"-results, but 372MHz reference-clock (what lot of people incorrectly refer to as "HTT") gives you nothing, when you clock down your RAM and get "normal" HTT-speeds with x2 or x2.5 multipliers.
Greetz, Flox
"Physics is like sex: sure, it may give some practical results, but that's
not why we do it." -- Richard Feynman.
"A Celeron is not so much a processor, it is more a collection of shorting links to allow the motherboard to work." - read on xtremesystems.org
yeah i know 1:1 is where it's at even with 372HTT 2:3 divider with ram at 248mhz 2-2-2-6 - memtest86+ reports bandwidth as 1710MB/s versus 245mhz 2-2-2-6 1:1 memtest86+ reports 1739MB/s
---
427 htt
ok, now i don't know what to doOriginally Posted by bigtoe
----- AMD K6-2 300 "Chomper" xxxxx xxxx xxxx /// 300 MHz @ 2,200 V -----
----- AMD Athlon XP 1700+ "Thouroghbred B" JIUHB 0306 MPMW /// 2400 MHz @ 1,900 V -----
----- AMD Athlon XP-M 2500+ "Barton" AQXEA 0327 UPMW /// 2450 MHz @ 1,850 V -----
----- AMD Athlon XP-M 2600+ "Barton" IQYHA 0401 XPMW /// 2500 MHz @ 1,750 V -----
----- AMD Athlon 64 3000+ "Newcastle CG" xxxxx 0418 WPMW /// 2600 MHz @ 1,600 V -----
----- AMD Athlon 64 3200+ "Winchester D0" xxxxx 0433 SPMW /// 2750 MHz @ 1,616 V -----
----- AMD Phenom II X2 555 BE "Callisto" xxxxx xxxx xxxx /// 4080MHz @ 1,375 V -----
----- AMD Ryzen "Zen" xxxxx xxxx xxxx /// TBA @ TBA -----
Bookmarks