OCZ DDR Diagnostic Booster Works on these Motherboards.

[RocKer]

<dutch mode on>
Yes :thumbsup: da was het,heb al gebeld ook,word opzij gelegd voor mij,morgen omgaan.
<dutch mode off>

Ok it was that easy to find tomorrow am going to the shop,and then burn those BH5 ,nice smiley yust like my nick .

thks cranox .

[zakelwe]

Put in Booster ..read 2.3v
Changed Bios to 2.7v .. booster read 2.5v
Took it out and changed screw clockwise
Put it in Booster reads 1.1v !
Took it out and put screw anticlockwise
Booster flickers on and then off.
Turned screw clockwise a lot .. machine does not boot up, Booster flickers and then dies

RMA time.



Regards

Andy

Ps The top heatsink was wobbly as well.

[Goyo]

[QUOTE]Originally posted by saaya
[B]

   Manufacturer           Motherboard        Max Voltage          Tested Compatible? 
 ...
      Asus                   P4P800             3.4V                       Yes 
      Asus                   P4C800-E           3.6V                       Yes 
      Asus                   P4R800-VM          3.4V                       Yes 
 ...

What about P4C800 Deluxe (No-E)?, can reach 3.6V VDimm?

Somebody has proven it?

[FX Freak]

does the booster work on the abit av8?

[goddh0r]

Anyone tried on Asus K8N-E Deluxe yet?

[jinu117]

Chaintech VNF3-250. It will take memory slot 2-3 out effectively leaving you with memory slot 1 only. THIS BITES HARD!!! As OCZ has listed MSI K8T Neo having this problem, why is the VNF listed as fine with no explanation like K8T? I made purchase based on this list and now stuck with product that can't physically go in with my 2 sticks of OCZ 3700EB and if I want to RMA, there will be even more shipping charges + 15% on restocking fee too !!! (not to mention having to do manual v-mod...which isn't hard but I prefer doing it off cleaner way).
Please advise someone from OCZ.

[RocKer]

Originally posted by bigtoe
Update from Eric

Epox 4PCA3 line of boards is a big NONO...don't try it.

Epox 8RDA3+ was fine though and worked well.

I have a 8RDA3+ rev2.1.

Where did you put the booster for dual mem to work,in dimm 3??,becaus dimm 1 and 2 are the one's to work in dual mode.

Dos it fit in dimm 3(center dimm),i have heatspreaders on my corsairs,do i need to remove them or not,becaus it don't fit in dear(dimm3).

If a put it in dimm2 then it will work but not in dual i think,i will try it out,but it works with you(so you told here on the board) so were did you put the booster.

I think a will try it first with some cheap twinmoss pc3200 sticks, i dont won't to fry my bh5's .

<edit>
I have try't a few things but no sigar yet ,but still going .

<edit2>
:banana4: yes i have a sigar,now booster 3.0v,bios readout 3.07v/3.12v,bios vcore auto,every things :thumbsup: and in cpu-z i see dualchannel .

Now am gone see how far i come with fsb,lets pump up that baby .

[jinu117]

Originally posted by jinu117
Chaintech VNF3-250. It will take memory slot 2-3 out effectively leaving you with memory slot 1 only. THIS BITES HARD!!! As OCZ has listed MSI K8T Neo having this problem, why is the VNF listed as fine with no explanation like K8T? I made purchase based on this list and now stuck with product that can't physically go in with my 2 sticks of OCZ 3700EB and if I want to RMA, there will be even more shipping charges + 15% on restocking fee too !!! (not to mention having to do manual v-mod...which isn't hard but I prefer doing it off cleaner way).
Please advise someone from OCZ.

Tonight, I said screw cleaness. Took out my soldering iron, few other odd tools, and took the molex connectors on DDR booster out, soldered wire straight to the pcb at the back side. Took off the heatsink and put it in DIMM 3 of my VNF3-250. Works quite well except, I notice over boiling temp on the mosfet (I always use infrared thermometer when I play with new stuff). So I pull it out, unsolder mosfets, solder it at the backside and give it oversized mosfet heatsinks. Now it is sitting happily there not to warm and working. Of course, I must voided all possible warranties, etc. And it doesn't look as clean as it could have been... But Alas, this was my only option as doing vmod with 50k resistor on mobo only nets me up to 3.15v for some unknown reason. (Of course, I found out my 3700EB doesn't react much better at higher volt... but was worth trying I guess, and only tried up to 3.25v or so so far).
OCZ, PLEASE, PLEASE, make one with components located on the other side of PCB so you can cover all crowd. It was just matter of placing components on the other side!
Also, warning to those that takes off the heatsink, prepare yourself for some burnt components. Those mosfets do run hot!

[Pejsen]

Hi just wanted to let you guys know that it works with the Gigabyte K8N nonPRO (ultra light version or something).

[jinu117]

Originally posted by Pejsen
Hi just wanted to let you guys know that it works with the Gigabyte K8N nonPRO (ultra light version or something).

!!!! What kind of cooling? I am IMPRESSED.

[Pejsen]

Originally posted by jinu117
!!!! What kind of cooling? I am IMPRESSED.

A blue Sunbeam LED-fan

Now @ 4.01V

[Obscure]

Anyone know if Corsair XMS 3200C2 Rev 3.1 likes high vdimm voltage? They use Infineon Rev B Chips. Any ideas? Im looking to get some EB sometime soon to replace this stuff...but id still like to know if anyone has had any experience with this stick.

[Narbo]

Has anyone tested with OCZ 3700 Gold Rev 1?

Also results with a regular P4C800 Deluxe would be cool. Im almost sure its the same as the P4C800-E but you never know until you know!

Edit: I have one on order now so I guess ill find out soon one way or another!

[Kalway]

infineon chips usually won't benefit much more after 3v

[mad mikee]

Yeah you can put the booster in slot 1 but if you try the mem in any other slot w bios F3, can't set OC settings (hangs, then on reset is back to defaults) Also pot runs into memory if in slot 3 and 1 stick only (no good) in slot 1. Same problems w/ VNF-250 (can't boot w/ booster in slot 1)

So this is a waste of my money, going to VDIMM mod the board, will still be better than nothing which is what I get w/ this.
:grr:

[moep]

If anyone out there gets to test the OCZ Booster with the new Abit AS8 (775 / i865PE) Board, I'd love to hear some feedback about it. I'm currently building a system with this board and the booster, but I'm not done yet so I can't test it out.
All I know is that the booster physically fits into the DIMM-Slots with the RAM in place.

[Onepagebook]

Abit Av8 also works fine! 3.1v

[Roadburn]

ASUS P4C800-E , 2.8@3.5, KHXpc4000/1G@2.5,3,4,5. They say 3.6V max but I can boost to measured and booster inidated 4.0V I run 3.0V, but CPU is the limiting factor 3.5Ghz is its max stable speed.
PS. this new kingston will boot 2,2,2,5@200

[yuri]

Why has no one tested this on a sk8v ?

its only the best motherboard on the planet

[Boogotop]

work great on my Gigabyte K8N (non pro)

doesn't tried over 3.75v



OCZ PC3700EB with 3.4v

[Juspriss]

What about MSI K8N Neo2 Platinum?

[moep]

yeehaa - the OCZ DDR Booster works like a charm in the Abit AS8 (LGA-775/i865PE)

[Gascogne]

Originally posted by Juspriss
What about MSI K8N Neo2 Platinum?

Would also very much like to know how the booster works with MSI K8N Neo2 Platinum.

[iceman2g]

Gascogne WELCOME TO FORUMS.

[Gascogne]

Originally posted by iceman2g
Gascogne WELCOME TO FORUMS.

Thank you
I forgot that I was new here while was typing my messeges here.