Ultra low profile 1.35v 30nm DDR3 capable of 2400MHz. Perfect for SFF builds.

[andressergio]

I never run vccio at anything over 1.0875 as it usually caused instability with my cpus and always 1.65v, and while benching 1.8v all the time for 224X 6-9-6-20 on the GSkill RipjawX BBSE sticks I have, no degradation or problems here.

I think the whole 0.5v vtt/vdimm rule was more so for Bloomfield and Gulftown.

yes l0ud its like that like OC nub said also, i was just guessing as it was real low vdimm so i get like scared lol

cheers !

[l0ud_sil3nc3]

yes l0ud its like that like OC nub said also, i was just guessing as it was real low vdimm so i get like scared lol

cheers !

moar voltz

but really I would probably stick with your current setup over these new samsung dimms seems like you have a good thing going with 16GB

[andressergio]

moar voltz

but really I would probably stick with your current setup over these new samsung dimms seems like you have a good thing going with 16GB

yeah this patriots are really good stuff i just put them back yesterday

[Punisher!]

yeah this patriots are really good stuff i just put them back yesterday

Could you please post some tests with CL 7, 8 and 9 please? (with lowest trcd possible of course)

I think until 1,65+V all voltages are totally safe.

You should try some stability test too as:
- Prime95 CUSTOM (after having selected "Blend", then "Custom") putting adequate memory size to be tested
or
- Memtest for Windows (several instances)

Thanks a lot.

Goodbye.

[andressergio]

Could you please post some tests with CL 7, 8 and 9 please? (with lowest trcd possible of course)

I think until 1,65+V all voltages are totally safe.

You should try some stability test too as:
- Prime95 CUSTOM (after having selected "Blend", then "Custom") putting adequate memory size to be tested
or
- Memtest for Windows (several instances)

Thanks a lot.

Goodbye.

yeah but it think OC nub tested a lot on the chipset that goes with this mem that is X79

[Punisher!]

yeah but it think OC nub tested a lot on the chipset that goes with this mem that is X79

Np mate! We'll wait for your results .

[Punisher!]

I'll get my sticks in 5 days. First european? First on AMD too?

[andressergio]

I'll get my sticks in 5 days. First european? First on AMD too?

good luck mate im very pissed that i have to move BCLK to get good results you know that moving bclk makes vcore hungry...

[Kristoferr]

I'll get my sticks in 5 days. First european? First on AMD too?

I should be getting my 30nm Samsa´s from Germany tomorrow or friday.

[Punisher!]

good luck mate im very pissed that i have to move BCLK to get good results you know that moving bclk makes vcore hungry...

They should be in flight Miami - Italy (customs fee already paid) in few houres according to tracking .

Fortunately my memory controller seems very good and accomodative too:
http://digilander.libero.it/m4puni/p...7_Prime_1s.jpg
http://digilander.libero.it/m4puni/p...ew_Prime_s.jpg
http://digilander.libero.it/m4puni/p..._2000Mhz_s.jpg
http://digilander.libero.it/m4puni/p...ite_test_1.jpg

[andressergio]

They should be in flight Miami - Italy in few houres according to tracking .

Fortunately my memory controller seems very good and accomodative too:
http://digilander.libero.it/m4puni/p...7_Prime_1s.jpg
http://digilander.libero.it/m4puni/p...ew_Prime_s.jpg
http://digilander.libero.it/m4puni/p..._2000Mhz_s.jpg
http://digilander.libero.it/m4puni/p...ite_test_1.jpg

nice results mate

yeah mine's strong also but the problem as guys explained is the 2400 strap on SB i have no value to choose between 2133 and 2400 so i can go to 2300 but pushing bclk

[PiLsY]

I'll get my sticks in 5 days. First european? First on AMD too?

Mine should be here by the end of the week . I got 1333mhz tho, you bought the 1600mhz kit didnt you?

[Punisher!]

Mine should be here by the end of the week . I got 1333mhz tho, you bought the 1600mhz kit didnt you?

Yeah, the amazon 1600 one!

[PiLsY]

I so hope I dont regret my itchy trigger finger and not waiting for the 1600 to come in stock...

[OC Nub]

@ LoudSilence

He was concerned about the .5v rule that started with bloomfield. I was trying to explain it the best I could. On x58 it was pretty hard to not follow this rule when ocing, it required more vtt than the new platforms.

I pretty much forgot about this after x58.

[OC Nub]

I would be surprised if anyone was able to do high frequency at c7 or even c8 on any platform. I think the benefit of this ram is the low profile, low voltage and low cost. Considering the default speed and timings it does clock very well, but its not going to clock head to head with most high performance, higher priced ram.

Could you please post some tests with CL 7, 8 and 9 please? (with lowest trcd possible of course)

I think until 1,65+V all voltages are totally safe.

You should try some stability test too as:
- Prime95 CUSTOM (after having selected "Blend", then "Custom") putting adequate memory size to be tested
or
- Memtest for Windows (several instances)

Thanks a lot.

Goodbye.

[andressergio]

@ LoudSilence

He was concerned about the .5v rule that started with bloomfield. I was trying to explain it the best I could. On x58 it was pretty hard to not follow this rule when ocing, it required more vtt than the new platforms.

I pretty much forgot about this after x58.

yes i was asking as i also forgot as i never had to use more than 1,08 on any of my chips but as i never tried 1,35v DDR3 i started to doubt

I would be surprised if anyone was able to do high frequency at c7 or even c8 on any platform. I think the benefit of this ram is the low profile, low voltage and low cost. Considering the default speed and timings it does clock very well, but its not going to clock head to head with most high performance, higher priced ram.

i tested lots of kits of 2x4 and the best RAM i tested is this Patriot Xtreme 2000 9-11-9-27, they run amazing above 2000 but u cant touch that 11, what i like of the samsungs is that they do flat timmings like good all hypers, for ex 2220 10-10-10 etc

what i dont agree is that higher priced RAM will do better, this Patriots cost 77 dollars 2x4GB and you will be amazed how they beat a 200 dollar kit, and i aint my luck or batch we bought like 6 kits of 8GB with some friends from ramexperts and all do same as mine

cheers
Sergio

[Punisher!]

I would be surprised if anyone was able to do high frequency at c7 or even c8 on any platform. I think the benefit of this ram is the low profile, low voltage and low cost. Considering the default speed and timings it does clock very well, but its not going to clock head to head with most high performance, higher priced ram.

Yeah but they are promising very well seeing the result. I don't see any more 8gb kits able to do that here so please keep on testing and post your results! Thank you!

[andressergio]

I so hope I dont regret my itchy trigger finger and not waiting for the 1600 to come in stock...

u wont PiLsY min u can get its 2133 CL10 1T at 1,5vdimm

[Punisher!]

u wont PiLsY min u can get its 2133 CL10 1T at 1,5vdimm

And you keep on testing too @~2000Mhz! I would like to see some Prime (follow the instruction above please)!!

[andressergio]

this is my comparison

samsung 4x4GB at 2200 10-10-10-30 1T



Uploaded with ImageShack.us

Patriots 4x4GB 2133 9-11-9-27 1T



Uploaded with ImageShack.us

[andressergio]

And you keep on testing too @~2000Mhz! I would like to see some Prime (follow the instruction above please)!!

lol yeah i will do soon dont worry

[Punisher!]

this is my comparison

samsung 4x4GB at 2200 10-10-10-30 1T



Uploaded with ImageShack.us

Patriots 4x4GB 2133 9-11-9-27 1T



Uploaded with ImageShack.us

You had +3 bus on Samsung test, you should repeat it @ same bus as Patriot.

[OC Nub]

The results I had posted were the best I was able to do with these.

I also tried them on my Gigabyte p67 board, but the results werent very good. The Asus board may be much better with this kit after seeing andressergio's results, or maybe I didnt find the right settings.
The Giga p67 did like the GSkill RipjawsZ 16gb kit, was able to run them at 2133 9 10 9 28 1t, 1.66vdimm http://www.xtremesystems.org/forums/...=1#post5008754. I think all boards act different with a particular kit of ram, some like kit A, and the next board doesnt, but clocks great with kit B for example.

I think they are a very good value and most people will be pretty happy with them.

Yeah but they are promising very well seeing the result. I don't see any more 8gb kits able to do that here so please keep on testing and post your results! Thank you!

[BeepBeep2]

@andressergio

CPU speed and BCLK affect results, do an apples to apples comparison at 2133 9-11-9 and 2133 10-10-10. Also, good hynix will do 2133 9-10-9, not 9-11-9...