Asus CHV Formula overclocking

[PatRaceTin]

what is NB Speed that does not show up in CPUZ ?

[chew*]

what is NB Speed that does not show up in CPUZ ?

Default 10x multi X 285 ref clock

[PolRoger]

Crappy pic but my good camera is in Austin TX.

Anyway got some time to play seeing as wife is off to work already.

Attachment 121303

Actually tossed a rig together in living room for pretesting for my second build. Plan to mirror my sandy bridge rig for the most part hardware and settings wise or at least come close.

Here's where my sandy rig sits daily, it's obviously stable



And here is where the mirror image BD Rig is sitting now.

NB @ 2600 for those that are curious.

I have a 8150/CHVF combo that should be arriving tomorrow and I'm looking to do something similar (comparison/mirror) with one of my "daily" 2600K combos. I'd be interested to see how this goes for you.

[chew*]

I have a 8150/CHVF combo that should be arriving tomorrow and I'm looking to do something similar (comparison/mirror) with one of my "daily" 2600K combos. I'd be interested to see how this goes for you.

Here's where i'm at so far as far as one game in particular, NB was stock for this test on BD.

Both systems are 4 core 4 thread, i find anything more than 4 pointless for gaming 90% of the time.

[Dumo]

Anyone know about K15 stats?

[Raja@ASUS]

0051 cpu fan error on boot up?

hitting reset button fixes it but

any ideas

Enter UEFI>Monitor>Fan Speed Control>CPU Q Fan Control = Enabled>Select Fan Type = PWM>CPU Fan Speed Low Limit = Ignored


-Raja

[Dumo]

Bios 9913

Catalyst 11.9 kept givin' problem for crossfire setup

[BeepBeep2]

Bios 9913

Catalyst 11.9 kept givin' problem for crossfire setup

That's on ambient, right?
If I knew I could get a CPU like that I won't mind buying BD. It seems like power consumption will go through the roof at those speeds/volts though.

Considering everyone has been using 2v+ on these CPUs with LN2, I'd be inclined to think that these CPU's are more voltage tolerant than Thuban/Deneb but leak more...correct?

With my 3x120mm radiator and AP-15's I doubt I'd need to worry about a temp wall.

[chew*]

He's on phase...... you might be able to suicide that on 1 core ambient ..........

[BeepBeep2]

He's on phase...... you might be able to suicide that on 1 core ambient ..........

Yeah, I should have skimmed through last page or two first or looked at the NB speed. I see that now.
You think 5 Ghz stable is doable on water with some chips? I'm still saving up, probably will have to go with the 8120...I just can't afford the 8150.

[chew*]

Yeah, I should have skimmed through last page or two first or looked at the NB speed. I see that now.
You think 5 Ghz stable is doable on water with some chips? I'm still saving up, probably will have to go with the 8120...I just can't afford the 8150.

It will require some binning for 5 gig.

[FlanK3r]

think, Daveburt has great FX...over 5100 MHz Cinebench with 1.4V looks awesome. Maybe he has gold one

[Dumo]

Using DOCP and ram profile 0 which is xmp 2133 C8

[FlanK3r]

2133 is no problem....I had 2200 8-9-7 stable. Keep pushing! Ah srry, DOPC profile...

[G.Foyle]

Nice IMC you have there Dumo, what Vtt is that at?

[Dumo]

Nice IMC you have there Dumo, what Vtt is that at?

You mean CPU/NB G? It was 1.45

[Dumo]

2133 is no problem....I had 2200 8-9-7 stable. Keep pushing! Ah srry, DOPC profile...

What are you talkin bout Flanker?

[PolRoger]

My 8150/CHVF combo came in yesterday afternoon.

It seems my chip has a default/PS0 (3600MHz) VID of 1.287. Ran a first o.c test with 1.35v @ 50% LLC cooled on air with TR Archon (push/pull). I usually run a daily "crunching" o.c. with my 2600K at 4.6 GHz (HT) ~1.3v (load) but with BD's higher TDP it may be hard to keep the temps manageable at 4.6+ eight core (load) on air.

[FlanK3r]

DUMO: nothink, I dont seen first time you are talking about DOCP profile for RAMs...And I thought, u show only max memory clocks :-)...

[Dumo]

My 8150/CHVF combo came in yesterday afternoon.

It seems my chip has a default/PS0 (3600MHz) VID of 1.287. Ran a first o.c test with 1.35v @ 50% LLC cooled on air with TR Archon (push/pull). I usually run a daily "crunching" o.c. with my 2600K at 4.6 GHz (HT) ~1.3v (load) but with BD's higher TDP it may be hard to keep the temps manageable at 4.6+ eight core (load) on air.

Nice PR
You'll have a lot of fun oc'ing this one. The Coolest working on Coretemp that can read BD's tdp/power draw

DUMO: nothink, I dont seen first time you are talking about DOCP profile for RAMs...And I thought, u show only max memory clocks :-)...

Thats ok Flanker DOCP and C6 enabled seem to help with stability and heat load in windows


Winrar...

[BeepBeep2]

What are you talkin bout Flanker?

I read that as
"2133 is no problem, (I didn't bother too look at your screenshot)....I had 2200 8-9-7 stable. Look at me. You, however...keep pushing! Oh wait, you can't (even though you can...), DOCP profile...

Thats ok Flanker DOCP and C6 enabled seem to help with stability and heat load in windows

I need DOCP to clock ram at all on CHV (with Thuban)...however with DOCP, 2050 6-9-6 was doable in 32M at 1.75v (6-10-6 isn't totally stable in itself...prime fails :/ )

Hopefully FX soon enough, just to try something new. Not impressed at all by performance.

[Dumo]

Not impressed at all by performance.

Well, probly you will have more fun with FX when you go cold.

I just want my thread (this thread) to be free from all negative comments that peeps posted @ other BD threads. I'm sick&tired with peeps shouting at ea. other

[BeepBeep2]

Well, probly you will have more fun with FX when you go cold.

I just want my thread (this thread) to be free from all negative comments that peeps posted @ other BD threads. I'm sick&tired with peeps shouting at ea. other

Yeah, I will be limited to dice for a while and from what I've seen 8150 is the way to go cold...no money for that.
LN2 price is through the roof so I will have to work with DICE again :/

The problem with BD for me is the performance:power ratio, (+ ST perf) its too inefficient. It almost seems that GloFo's 32nm is worse than their mature 45nm.

Mind if I post any Thuban results? I've got nothing else to do but run wPrime 32M, pifast, Cinebench 10 / 11.5, SuperPi 1M+32M etc.

EDIT:
(Sorry for littering with more BD 'hate' )

[Dumo]

No problem Beep

[PolRoger]

Well I've been testing my 8150 some more today and it seems that it may have one weak module/cores?

I'm not having much luck when I attempt to stress with Prime it usually/mostly fails (sum out error) in thread 7 but sometimes thread 8 will fail instead. I'm not sure if there is some voltage or setting I'm skimping on but I'll keep working it. I may have to bin another chip if they ever get some in stock at my local Micro Center. My combo so far has rarely blue screened and the few times it happend was while trying to load into windows at 5.2GHz with not enough vcore and too much vdroop. http://valid.canardpc.com/show_oc.php?id=2056223