Another SR1 560mm inside FT02 (source ocn silverstone club gallery):
Another SR1 560mm inside FT02 (source ocn silverstone club gallery):
^ that was pretty much exactly what I was thinking when I had my FT02
If the case was just a hair longer it would fit a bit nicer (the Rad).
Only thing I would change would be toadd a hot swap 5.25 HDD enclosure (4x 3.5" drives in carriers) and a 5.25" drives adapter/cage to be mounting for 2 x Slim Optical Disc Drive into a 5.25" Bay
Great builds guys! Planning a Raven 02 / Fortress 02 water cooled build. Quick question: If you have a "thick" rad, say about 55mm, in the bottom plus regular 120/140 fans, does a GTX 580 fit?
E8400, P5Q-E, Crucial 2x2GB , XFX 8800GTX , Corsair HX620W
D-TEK Fuzion, MCW60, Thermochill PA120.2, MCP655
I think it will not fit.
I have a Black Ice SR1 + 25mm fans, and with GTX580 Reference Design i had like 1cm of space.
Now with the GTX580 Matrix Platinum which is larger than reference... i had to replace my radiator with a slim one (MCR320 XP).
BTW, this is how it look right now... after radiator and vcard changes...
i7 2600K | Asus Maximus IV Extreme | 8GB DDR3 1600 C9 Corsair Vengeance | GTX580 Matrix Platinum | Vertex 2 120GB | Auzen X-Fi HomeTheater HD | Corsair AX1200 | FT02
EK Supreme HF Full Nickel | MCR320 XP + GT AP15| DDC3.25 + EK Top V2| EK Multioption Res X2 150 Advance | Bitspower Fittings & Rotaries
My flickr
.. And if it's card like 30cm long 5970? And if fans on push-pull? :/
Eek, how nice would be if case were a little notch higher.
E8400, P5Q-E, Crucial 2x2GB , XFX 8800GTX , Corsair HX620W
D-TEK Fuzion, MCW60, Thermochill PA120.2, MCP655
Sorry... english is not my primary language....
I will try to explain it better... haha
Ok, what i wanted to say is... You have less than 1cm space left between vcard and radiator with 25mm fan. But, also i have to admit i thought wrong with the size... i was thinking about radiators like Thermochill or XSPC RX when you said "thick" rads and did not read what you wrote after, "about 55mm" part... So, yes, now after reading correctly, I rectify, it will fit with a 55mm radiator.
Last edited by kpablo; 09-26-2011 at 03:14 PM.
i7 2600K | Asus Maximus IV Extreme | 8GB DDR3 1600 C9 Corsair Vengeance | GTX580 Matrix Platinum | Vertex 2 120GB | Auzen X-Fi HomeTheater HD | Corsair AX1200 | FT02
EK Supreme HF Full Nickel | MCR320 XP + GT AP15| DDC3.25 + EK Top V2| EK Multioption Res X2 150 Advance | Bitspower Fittings & Rotaries
My flickr
I am new to this forum, saw the thread and thought I would post. I dont have a boss Liquid cooling setup yet, but I am in the process. I am waiting on my new mobo to arrive, so I thought I would fab some mounts for a 240mm radiator, with side exhaust. I will be modifying the side of the case as well. Next step is to grab a water block for my CPU and GPU's and get away from my old H100 liquid cooler.
WTFBOOM - I have a Raven 02 with an H100 running my machine in the sig below. You can remove the middle and rear bottom fans and mount your H100's radiator. It works very well. I will post some pics later.
CPU - Intel i7 2700K @ 5.2Ghz (1.38v)
Cooling - Corsair H100i With 4 X 120MM OEM Corsair Fans
System Board - Asus P8Z68-V Pro
Memory - G.Skill RipJaws-Z 2X8GB DDR3 2133Mhz @ 9-10-10-28 1T
SSD1 - 240Gb Samsung 840 Pro
SSD2 - 128GB OCZ Vertex 3
HDD1 - 1TB WD Black
HDD2 - 2TB WD Green
DVD - Liteon 22X DVD R/RW
GPU1 - EVGA 670 GTX FTW 2GB
PSU - 750W XFX XXX Edition
Case - Silverstone Raven-02 Case
Monitors - 3X Asus VX238H's and HANNS-G 28"
Hey quicksilver, I look forward to the pics!
I had similar mounts to the ones I just made, that mounted the Radiator flat-across the 180mm Rear and Middle fans, but the radiator caught all of the air flow. I felt that I could be getting better air-flow to my mainboard. That is why I decided to make mounts for the radiator, I am hoping that I see a noticeable decrease in heat on my mainboard/RAM etc.. If I had a full mobo/GPU waterblock setup, then I would definitively be rid of the 3 stock 180mm fans for 4 140mm with a bigger radiator.
sigh... one day
Hey guys, not even sure if this post will work but here goes, first time water-cooling, lots of experience building PC's though. Very happy with the build, (pics should be attached). 2 issues though, firstly i am concerned that the RAM cooler i added is being heated up by the loop too much and i am going to 'melt' my RAM, temps got up to 55C after a little benching... on that note i am running the Prolimatech Blue Vortex 14 fans ( http://www.prolimatech.com/en/produc...?id=160&page=1 ) are these fans any good?, it'll be a pain to replace them but if i will get a significant performance boost with other fans id be happy to, any ideas? Or just any ideas in general for what you can see?
Will an EK XTX 120 fit on top of the Raven 2?
It should, there are examples of all kinds of thick rads mounted there (in raven and fotress), including old EK 120.1 radiator (previous page).
As for the thread, FT02 + 3x180 radiator + tri sli
Source: http://www.overclock.net/case-mod-wo...0mm-rad-6.html
where on earth did he get that rad from? whos the manufacturer?
Its a magicool rad. Here is a thread about it
My Rig:
Motivation 2.0
----------------
Check out my Build log!!!
Motivation: Sponsored by Galaxy and Corsair
---------------
Check out below for videos and reviews!!!
Facebook Youtube Instagram Twitter
Hi guys,
Great cases! I have a query though.
My HD6990 is watercooled and I am considering this case. I have a 360 SR1 currently and would like to keep using it with the FT02.
The motherboard (X79 Sabertooth) has a x16 PCI-e slot as the very last slot (1.5cm from the bottom of the mobo) which I could use. Can any of you guys see a possibility that I would have enough clearance for the card if I have it in the very bottom slot and the 360 rad at the bottom of the case?
Here is one from norway(not me) with FT-02 and the 3x180mm rad:
_MG_3846.jpg
http://www.diskusjon.no/index.php?sh...ost&p=18953728
His specs:
EK-bay spinreservoir
Laing DDC-1tplus pumpe
Magiccool 3x180 slim rad
2x EK gtx580 with serial link
EK supreme HF EN
Silverstone Fortress FT-02
Corsair AX1200 psu
Asus maximus extreme-z
i72600k@4,8
4x8gb corasair vengeance 1600
2xGTX580
Asus Xonar Essence STX
X2 555 @ B55 @ 4050 1.4v, NB @ 2700 1.35v Fuzion V1
Gigabyte 890gpa-ud3h v2.1
HD6950 2GB swiftech MCW60 @ 1000mhz, 1.168v 1515mhz memory
Corsair Vengeance 2x4GB 1866 cas 9 @ 1800 8.9.8.27.41 1T 110ns 1.605v
C300 64GB, 2X Seagate barracuda green LP 2TB, Essence STX, Zalman ZM750-HP
DDC 3.2/petras, PA120.3 ek-res400, Stackers STC-01,
Dell U2412m, G110, G9x, Razer Scarab
Lowfat....beautiful work there, brother. Can you talk to me about the rad/fan setup? I'm guessing that is a triple 180 (who makes it?) and can you just bolt it on top of the stock penetrator fans? Or did you have to remount everything?
Thanks, you inspired me to make a decent home for my mid tower Lian Li, which is getting kinda warm with these 7970s...
-------------------------------
Not From Concentrate
All Projects
Previous Projects:
S3 Mini ITX Chassis
The ArK
Uriel
Israfel
Veritas
Eldritch
That rad is getting more and more popular, some examples:
http://forums.overclockers.com.au/sh....php?t=1007404
*******************************
http://forums.overclockers.com.au/sh....php?t=1005753
*******************************
http://hardforum.com/showthread.php?t=1669157
******************************
enough room for sandwich..
******************************
https://www.evga.com/forums/tm.aspx?m=1453073&mpage=1
******************************
Thanks for posting these pics, aerial. I LOVE the look of this case, and that radiator seems to be a perfect fit.
I am strongly considering getting a FT02 due to this thread...
Bookmarks