***Official***Z68X/P67A-UD7 Club/Discussion/Info**

[sin0822]

nice job guys!

[andressergio]

nice job guys!

thx sin

[Falkentyne]

Ok since andre wanted me to do it,
and even though I know this isn't the right thread, here's proof my UD5 can boot up at 106 BCLK on the first try, INTO windows.

Also notice that windows system properties no longer says 3.4 ghz is the default speed, too...

[andressergio]

Ok since andre wanted me to do it,
and even though I know this isn't the right thread, here's proof my UD5 can boot up at 106 BCLK on the first try, INTO windows.

Also notice that windows system properties no longer says 3.4 ghz is the default speed, too...

goooood job

[Falkentyne]

BTW that bclk wasn't even 1/100th of a way close to stable. can't run ANYTHING that puts a load on, except IE....tried to run prime blend and it rebooted the instant i pressed "start." I'm not exaggering when I say "instant." And boy, did trying to load minecraft cause my x-fi to emit the most horrible screeching noise you ever heard (computer turned off automatically a second later).

Tried raising VTT to 1.2v...didn't help.
Tried VTT at 1.1v, VCCSA at 0.975v, and XP didn't even finish loading... lol?

[andressergio]

BTW that bclk wasn't even 1/100th of a way close to stable. can't run ANYTHING that puts a load on, except IE....tried to run prime blend and it rebooted the instant i pressed "start." I'm not exaggering when I say "instant." And boy, did trying to load minecraft cause my x-fi to emit the most horrible screeching noise you ever heard (computer turned off automatically a second later).

Tried raising VTT to 1.2v...didn't help.
Tried VTT at 1.1v, VCCSA at 0.975v, and XP didn't even finish loading... lol?

mine was very stable at 107 and in W7x64 wich is harder than XP but no go to boot over 107 at 108 i just cant it goes back to def settings or boot loops, but less than that i can run SPI or browse didnt try prime just AIDA and all that things i showed

cheers !
Sergio

[C-N]

Originally Posted by Falkentyne
BTW that bclk wasn't even 1/100th of a way close to stable. can't run ANYTHING that puts a load on, except IE....tried to run prime blend and it rebooted the instant i pressed "start." I'm not exaggering when I say "instant." And boy, did trying to load minecraft cause my x-fi to emit the most horrible screeching noise you ever heard (computer turned off automatically a second later).

mine was very stable at 107 and in W7x64 wich is harder than XP but no go to boot over 107 at 108 i just cant it goes back to def settings or boot loops, but less than that i can run SPI or browse didnt try prime just AIDA and all that things i showed

cheers !
Sergio

Hey Fakl on my UD5 one of my 2500's (the only one that makes 107+ BCLK was prime & linx stable at maximum BCLK on the 2133 mem multi provided the CPU multi was reasonable making 5 ~ 5.3GHz. My current 2500K has always from new run 104.4BCLK (BIOS) x 48 = 5GHz & is linx/prime stable so I'm sure its got to be a combination of settings holding you back.

I know its hard to test when your rig reboots (maybe try a low multi to get BCLK going) but I found SPI 32M to be a good test to get VTT & SAV in the ballpark as too much or too little caused it to fail sooner. I also need a little more vcore to run higher BCLK & a lower multi.

[andressergio]

Hey Fakl on my UD5 one of my 2500's (the only one that makes 107+ BCLK was prime & linx stable at maximum BCLK on the 2133 mem multi provided the CPU multi was reasonable making 5 ~ 5.3GHz. My current 2500K has always from new run 104.4BCLK (BIOS) x 48 = 5GHz & is linx/prime stable so I'm sure its got to be a combination of settings holding you back.

I know its hard to test when your rig reboots (maybe try a low multi to get BCLK going) but I found SPI 32M to be a good test to get VTT & SAV in the ballpark as too much or too little caused it to fail sooner. I also need a little more vcore to run higher BCLK & a lower multi.

hey C-N so you say bclk its not limit of board but chip ?