Unofficial Gigabyte GA-X58A-UD9 Thread

**Salamndar** · 02-26-2011, 03:24 AM

I have issue with Easytune 6, it says CPU or RAM not supported!!!!!!!

My CPU is 980x, RAM is OCZ blade DDR3 2000 CL9

**godzzila** · 02-26-2011, 05:31 AM

Originally Posted by dinos22

looks as though display thingie is dead but board still alive LOOOL

Yes.. look at the picture:
http://img291.imageshack.us/i/74687741.jpg/

MB is working fain (I write from that) but POST display shows still 88.

I was stupid that LN2 cool it so hard. Snow and ICE was everywhere but everything was ok than I see that post disp show 88 during 3D Mark Vantage running..
So I thought that is only now it is water somewhere and it will be ok after end session but it is not..
Now it is few days after show and POST display still "death".

Yeh it is fail somewhere but anyone knows where is chip which drive POST display?

**CryptiK** · 02-26-2011, 06:21 AM

Originally Posted by bassplayer

Would you mind posting the subs for your GT's? I always have issues with my STT hypers running over about 1800MHz. They can do 1800 6-6-6 but can't do 2000 9-9-9

Sure here's my Corsair 2000GTC8 SPD. Sub timings for view too, set to auto in BIOS with ram at DDR3-1790MHz.

**Shiranui Gen-An** · 02-26-2011, 07:58 AM

I tried using the Dominator SPD with the STT sticks, didn't make any difference. Something is just...off about those sticks.

**Callsign_Vega** · 02-26-2011, 12:23 PM

Originally Posted by Salamndar

I have issue with Easytune 6, it says CPU or RAM not supported!!!!!!!

My CPU is 980x, RAM is OCZ blade DDR3 2000 CL9

I also get that message with a 990x and A-data XPG Plus V2.0 2200+ RAM.

**Salamndar** · 03-04-2011, 01:23 PM

Guys, what ever I do I can't boot with Bclk higher than 156 !!!!!!!!

**acebmxer** · 03-04-2011, 03:34 PM

Originally Posted by Salamndar

Guys, what ever I do I can't boot with Bclk higher than 160 !!!!!!!!

More info.... Post you full bios settings so we can advise what may be the issue.

**Salamndar** · 03-04-2011, 07:01 PM

Originally Posted by acebmxer

More info.... Post you full bios settings so we can advise what may be the issue.

LOL, I've opened a thread @ tweaktown about this and you also replyed there

Any way, I've tried F3, F4, F5i. F5L and all gave me the same issue, but I found out that if I turned of HT I was able to boot and stabilize @ 160 MHz, I have not tried to push more because it is too late where I live and should try tomorrow.

**Salamndar** · 03-05-2011, 10:44 AM

Let's see, I was able to boot with Bclk 166 if I turn off HT !!!

Bclk of 167MHz and I get the following issue, please refer to the you tube clip below :

http://www.youtube.com/watch?v=NG4h8JhfuvA

**dinos22** · 03-05-2011, 02:10 PM

take it all out of the case, pull it all apart, take battery out, clear cmos, use one stick of ram, one GPU, only keyboard and mouse plugged in, load optimised defaults and set 200x17, set ram on 1:8 ratiom vtt 1.3, vdimm 1.66 using stock heatsink or something and see if it loads

see if that works

oh also, have a good look at CPU and socket pins in case there is some markings on CPU pads maybe and if you have metho clean the CPU pads too before reinstalling the chip back into socket

**Salamndar** · 03-13-2011, 08:36 AM

Originally Posted by dinos22

take it all out of the case, pull it all apart, take battery out, clear cmos, use one stick of ram, one GPU, only keyboard and mouse plugged in, load optimised defaults and set 200x17, set ram on 1:8 ratiom vtt 1.3, vdimm 1.66 using stock heatsink or something and see if it loads

see if that works

oh also, have a good look at CPU and socket pins in case there is some markings on CPU pads maybe and if you have metho clean the CPU pads too before reinstalling the chip back into socket

Tried that, no luck !!!

**Lsdmeasap** · 03-19-2011, 09:06 PM

Something of interest to UD9 owners here, enjoy

http://www.mediafire.com/?1f2c15pchb7z64s

**Callsign_Vega** · 03-19-2011, 10:40 PM

Sweet thanks. From the mod file:

J.Micron/Gigabyte - v1.07.06 << Already there

New
Intel RAID - v10.1.0.1008
Realtek - v2.30

**Lsdmeasap** · 03-20-2011, 01:22 AM

Thanks, looks like I wrote the info wrong on that

Realtek is 2.39, repackaged and new link added above.

**wtfdc** · 03-20-2011, 02:39 PM

Does this board support Intel Xeon W3670 ?

**wibujo** · 03-20-2011, 03:32 PM

What is the max vCore of the 980X ??? Does it have something to do with snap, crackle, pop or core temps ??? Since this is a board specific Forum (UD9) I thought it would be best to ask for help here. I've spent many many days trying to OC my UD9/980X @ 4.84GHz with no success. Currently Vcore=1.59375v - QPI/vtt=1.455v. Still getting BSOD code 101 - max core temp 84c. I will be getting a 990X in the near future - maybe sooner if this CHIP doesn't make to 4.84 before it fries. lol. (I'm on water) If someone has had any luck wiyh 4.8 and above - would you please post a template or PM me one ??? Trying to stay sane - Thanks wibujo

**Lsdmeasap** · 04-09-2011, 09:41 AM

Mod to 10.5.0.916 (Change log in download) - tested and working - enjoy!

http://www.mediafire.com/?i62taf8rxtwb43g

**Hondacity** · 04-09-2011, 09:45 AM

ud9 is eol?

**Lsdmeasap** · 04-09-2011, 10:31 AM

Ya, is replaced with X58A-OC I believe

**Hondacity** · 04-09-2011, 11:23 AM

Originally Posted by Lsdmeasap

Ya, is replaced with X58A-OC I believe

do you think gb will make something like the "expander" board?

**Hondacity** · 04-09-2011, 11:23 AM

Originally Posted by Lsdmeasap

Ya, is replaced with X58A-OC I believe

do you think gb will make something like the "expander" board?

for the ...x58a-oc?

**Lsdmeasap** · 04-09-2011, 12:58 PM

I dunno? I don't think the Expander ever went retail did it?

I think I remember reading a thread here not long ago where people were arguing about it never being available.

**Callsign_Vega** · 04-13-2011, 09:29 PM

Originally Posted by Lsdmeasap

Mod to 10.5.0.916 (Change log in download) - tested and working - enjoy!

http://www.mediafire.com/?i62taf8rxtwb43g

Thanks, working great!

Thread: Unofficial Gigabyte GA-X58A-UD9 Thread

Thread Tools

Search Thread

Rate This Thread

Display

Bookmarks

Bookmarks

Posting Permissions