New batch 980x is a little devil :D 3018B179

[subaruwrc]

hard to say 1005 hard restarts sometimes when I only change the bclk or multi, 704 never seems to do that but CBB is -130c so its not a big deal for me.
I had issues with 2:12 on the 1005 but i seem to be the problem and not the bios!

2:12 is an interesting thing with 1005 bios
simply on air, changing the default settings to 133 / 1600 ram 2933 uclk , and the board wont post. cpu led blinking... BUT , if i change the mem multi from 10 to 14 - easyboot, and after that, 12 boots easily too... who understands..
and it seems to me, x23 uncore multi gives higher uncore mhz with low vtt, but x22 goes higher with higher / 1.4v+ vtt /

[Splave]

2:12 is an interesting thing with 1005 bios
simply on air, changing the default settings to 133 / 1600 ram 2933 uclk , and the board wont post. cpu led blinking... BUT , if i change the mem multi from 10 to 14 - easyboot, and after that, 12 boots easily too... who understands..
and it seems to me, x23 uncore multi gives higher uncore mhz with low vtt, but x22 goes higher with higher / 1.4v+ vtt /

Same here, minus the vtt

[[XC] gomeler]

Glad I'm not the only person with weird uncore/memory divider problems on the RIIIE. I've locked in a few various combinations that work but it took a whole lot of cursing and mashing of the power button to achieve it. Very nice chip there Splave, mad jealous here

[subaruwrc]

Glad I'm not the only person with weird uncore/memory divider problems on the RIIIE. I've locked in a few various combinations that work but it took a whole lot of cursing and mashing of the power button to achieve it. Very nice chip there Splave, mad jealous here

Ive spent the free minutes / hours of my last week to figure this out, but cannot get it straight. maybe there is something between dram volt + vtt volt + uncore + ram mhz and multis. donno what but its strange, that x22 uncore goes higher with high volt, then x23 , but x23 goes higher with low volt lol...

as I looked older test pics, x20 uncore went up to 4180mhz pifast, on the first ln2 test, last time It couldnt reach anything higher than 4100mhz ...

[subaruwrc]

I think its not surely R3E but gulftown imc related. my 920 bloomie can boot in R3E with any ram - uncore multi , in any condition and its imc can go up to 4900mhz + ... / not maxed /

[Splave]

Ive spent the free minutes / hours of my last week to figure this out, but cannot get it straight. maybe there is something between dram volt + vtt volt + uncore + ram mhz and multis. donno what but its strange, that x22 uncore goes higher with high volt, then x23 , but x23 goes higher with low volt lol...

as I looked older test pics, x20 uncore went up to 4180mhz pifast, on the first ln2 test, last time It couldnt reach anything higher than 4100mhz ...

still dont get why it boots 2:14 no problem and then 2:12 works

[subaruwrc]

still dont get why it boots 2:14 no problem and then 2:12 works

dont get it either m8

but it can boot this way anytime ...
from 10 to 12 no go
from 10 to 14 then 12 easy ...

[Nanok]

Did test som voltage, and cb/cbb testing this weekend.

1.8Vcore, cb non, and cbb -140, i thinks its a keeper :-)

[Splave]

schweet chip

[Linuxfan]

Did test som voltage, and cb/cbb testing this weekend.

1.8Vcore, cb non, and cbb -140, i thinks its a keeper :-)

Nice!
Splave what does yours do max in 1M?

[Splave]

6320mhz found a new bios that fixed my vtt problem though so maybe more?