** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[Gaul]

for the UD3P rev 1.0 was the F10b Rob dunno for the UD3R

and the best bios on UD3P rev 1.1 is ???

[andressergio]

and the best bios on UD3P rev 1.1 is ???

dunno my friend as i never got it for the problems i describe

[Gaul]

dunno my friend as i never got it for the problems i describe

well, now i'm use F10 on rev 1.1, yups trobles on mem dev

[l0ud_sil3nc3]

I have f9 on my UD3R v 1.1 and I too was also wondering what the best bios would be?

[radaja]

has anyone else encountered this problem/
when you disable the advance cpu features(eist speedstep)
the board will endlessly reboot until you turn the PSU off
and have to turn the PSU back on restart to get it to boot?
it did this with my last UD3R and my third UD3P.every time
i disable speedstep,eist(even at stock setting)endless reboot.

[In-Fluence]

Never had that myself mate, only if settings were too adventurous, but EIST & speedstep should offer more stability. Perhaps a re-seat of the CPU and clean of the pads?

I'm going to be moving to a bigger place soon, and finally have a room dedicated to my gadgets! This means I might well set up a little benching station and get my USB3P fired up again after I'm settled in a few months.

[andressergio]

has anyone else encountered this problem/
when you disable the advance cpu features(eist speedstep)
the board will endlessly reboot until you turn the PSU off
and have to turn the PSU back on restart to get it to boot?
it did this with my last UD3R and my third UD3P.every time
i disable speedstep,eist(even at stock setting)endless reboot.

no Rob never but you read about the S1 to S3 states ? maybe its that bothering you

Try to do this...

1) load optimized feds
2) disable one at time and see wich is causing this

UD3P's do that when mem timmings or PL is hard

get me on msn i'll help

Best
Sergio

[radaja]

its not a big deal, after i load optimized defaults and reboot
then turn off the advance features,i just turn the PSU off before
it even goes into the reboot(because i know its coming)now.

EDIT:i tried turning them off individually,its seems that its actually
Virtualization Technology when disabled or enabled that causes it.
could someone try loading optimized defaults and the rebooting into
the bios and disable Virtualization Technology and see what happens?
thanks

[Strike@ps3]

HI all ,

i got E6750 G0 overclocked to 3.424Ghz stable core volt set in the bios 1.3625V cpu-z shown 1.328 volt bus speed is 428mhz

using a giga P45-ep45-Ud3lr MB .

using 2 x 2gb ocz ati crossfire rams 800mhz
ram timing is 5-5-5-18 running 1:1

using thermalright VX with scythe s-flex G to cool down.

how high am i able to overclock even more ? with what suitable core volt and the bus speed.

Thanks

[andressergio]

its not a big deal, after i load optimized defaults and reboot
then turn off the advance features,i just turn the PSU off before
it even goes into the reboot(because i know its coming)now.

EDIT:i tried turning them off individually,its seems that its actually
Virtualization Technology when disabled or enabled that causes it.
could someone try loading optimized defaults and the rebooting into
the bios and disable Virtualization Technology and see what happens?
thanks

i dont own a UD3R but no probs on my UD3P / USB3P such a weird thing Rob

[l0ud_sil3nc3]

i dont own a UD3R but no probs on my UD3P / USB3P such a weird thing Rob

your chip is at the post office

[Marke]

I'm thinking about buying a brand new Gigabyte GA-EP45-UD3P Rev1.6 for $120. from a individual not from a store the guy says he bought it less then a year go and will give me a copy of the sales slip.

Does anyone know if Gigabyte will warranty the board for me if i have any issues with the Rev.1.6 being that I bought it from a third party and not direct from a store ?

Also are people still having problems with the Rev.1.6 or is there a know issue that was resolved ?

[CHiLLiN1369]

warr shouldn't be an issue at all.

i have a 1.6 and it's fine. some say the rev 1.0 and 1.1 OC memory better.

[Marke]

Thanks for the reply

So $120 for a new never used board sounds like a good deal ?

warr shouldn't be an issue at all.

i have a 1.6 and it's fine. some say the rev 1.0 and 1.1 OC memory better.

[NoGuru]

http://valid.canardpc.com/show_oc.php?id=1368157

[radaja]

NoGuru,very nice.i need to get a decent chip.ive got two UD3R's
a 1.0 and 1.1,and two UD3P's both 1.1's and i need another chip to determine which
board is the best(hard to do with only one chip).especially when the cpu isnt great
to start with.i need a gem

[NoGuru]

NoGuru,very nice.i need to get a decent chip.ive got two UD3R's
a 1.0 and 1.1,and two UD3P's both 1.1's and i need another chip to determine which
board is the best(hard to do with only one chip).especially when the cpu isnt great
to start with.i need a gem

I have played with all three and can't really tell the differance in them.
A side by side benchmarking comparison would be great but so many variables.

[radaja]

yep same here,except havent tried any 1.6 boards yet.
not really trying to find an answer to the question of which
is better 1.0 vs 1.1 vs 1.6.im just trying to find the best
two boards to keep for my OCing fun
i will use the exact main components
like ram/psu/cpu/HD/cooling.i just need
to put in the tweaking time to get the
best results from each board.

so no i have 2xUD3R's 1x1.0 and 1x1.1
3xUD3P's 1x1.0 and 2x1.1's

i plan on keeping one UD3P and one UD3R

[NoGuru]

yep same here,except havent tried any 1.6 boards yet.
not really trying to find an answer to the question of which
is better 1.0 vs 1.1 vs 1.6.im just trying to find the best
two boards to keep for my OCing fun
i will use the exact main components
like ram/psu/cpu/HD/cooling.i just need
to put in the tweaking time to get the
best results from each board.

so no i have 2xUD3R's 1x1.0 and 1x1.1
3xUD3P's 1x1.0 and 2x1.1's

i plan on keeping one UD3P and one UD3R

I suck at math, but believe that is 7 EP45's.
I'm starting to look at 1156 to bench.

[radaja]

only 5 2 ud3r's and 3 ud3p's
i3-530's are fun but memory suks

i7-920's are the all around best though
high OC's and great memory performance
1366 setups are monsters machines

[zsamz_]

I suck at math, but believe that is 7 EP45's.
I'm starting to look at 1156 to bench.

he benched 7 1156 gigabut boards and cpus too lol

[Marke]

Anyone know where i can find a good deal on a EP45-UD3P or maybe someones looking to sell one ?

[zsamz_]

Anyone know where i can find a good deal on a EP45-UD3P or maybe someones looking to sell one ?

i got a 1.0 with 8 hours of use
got in new from rma

that was fast
everyone gigabut crazy lol

[gugle]

NO, too HOT
just can do prime 95 with small fft, and i'll stop them after 20m

which values of voltages in the bios ?
using aircooler or water ?

[kpo6969]

and the best bios on UD3P rev 1.1 is ???

F11c

http://forums.tweaktown.com/gigabyte...tml#post369165


hey radaja
didn't realize you had so many boards.