** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[andressergio]

You should be able to get the timings even tighter than that, something like 6-6-4-16-52.

yes i did it hoss and its very nice but not even went above stock vdimm yet and dunno how much i can use on 24/7 for hypers...

i did some nice runs at 6-6-4-18-62

[Hoss331]

I think lower-mid 1.7s is generally considered safe for 24/7 but not 100% sure. For 24/7 use I never really needed to raise vdimm above stock, but I only primed this setup to 506*9 1620 6-6-4-16-52, I always ran mine at 1.66 bios which is like 1.63v.

[andressergio]

I think lower-mid 1.7s is generally considered safe for 24/7 but not 100% sure. For 24/7 use I never really needed to raise vdimm above stock, but I only primed this setup to 506*9 1620 6-6-4-16-52, I always ran mine at 1.66 bios which is like 1.63v.

yes i checked when you posted here

http://www.xtremesystems.org/forums/...05132&page=213

you are runing PL8, im on PL7 and you needed 1,7 set on bios wich idles at 1,66

Thanks for the tips hypers are like old good D9 as zsams said

[zsamz_]

yes i checked when you posted here

http://www.xtremesystems.org/forums/...05132&page=213

you are runing PL8, im on PL7 and you needed 1,7 set on bios wich idles at 1,66

Thanks for the tips hypers are like old good D9 as zsams said

ya but expensive to collect
i have 4 triple chanel sets
sold of my 12gb of dominator gt

[Hoss331]

yes i checked when you posted here

http://www.xtremesystems.org/forums/...05132&page=213

you are runing PL8, im on PL7 and you needed 1,7 set on bios wich idles at 1,66

Thanks for the tips hypers are like old good D9 as zsams said

That was the baseline run for this setup to get a workable template, all runs after used 1.66 bios. With F8c PL8 is the lowest it will let me drop but PL wont affect vdimm.

http://www.xtremesystems.org/forums/...postcount=5542

[andressergio]

Still on stock vdimm pushing and testing what are the best timmings, so far loving this ones

X3380@ 4500
ST 2200 CL8@ 1600 6-6-5-18 trfc 52 Performace Level 7 - Vdimm 1,65








cheers
Sergio

[invict]

Hi guys i have a couple of question´s
Iam looking for a chipset cooler for ep45-ud3p , iam using a thermalright ultra extreme and the 1st pci-e 1x is being used by my xonar stx , so in your opinion is there any cooler that can fit in?
Other thing is , if i place the sound card in the pcie 16x orange the first one will work @ 8x like it did when you used 2 gpus?
Thz in advance.

[andressergio]

Hi guys i have a couple of question´s
Iam looking for a chipset cooler for ep45-ud3p , iam using a thermalright ultra extreme and the 1st pci-e 1x is being used by my xonar stx , so in your opinion is there any cooler that can fit in?
Other thing is , if i place the sound card in the pcie 16x orange the first one will work @ 8x like it did when you used 2 gpus?
Thz in advance.

why u need ? im using a fan near it and pushing 1,52MCH

when using 2 PCIE both will work at x8

Cheers
Sergio

[invict]

1.52 for 500 fsb it´s that safe for 24/7?
Iam struggling to get the chipset stable , iam using @ 500 fsb @ 1.38 and using 900,900,0,50? any suggestion on that aspect?

[andressergio]

1.52 for 500 fsb it´s that safe for 24/7?
Iam struggling to get the chipset stable , iam using @ 500 fsb @ 1.38 and using 900,900,0,50? any suggestion on that aspect?

for pushing tight timmings i need it, linx stable needs it so games like BC2 i just keep MCH as cooler as i can

Cheers
Sergio

[jjjc_93]

Anyone else on the EP45T-UD3P not able to adjust memory timings with memset?

So annoying having to keep going back to the bios to tighten timings after achieving a good overclock.

[andressergio]

Anyone else on the EP45T-UD3P not able to adjust memory timings with memset?

So annoying having to keep going back to the bios to tighten timings after achieving a good overclock.

? it works perfect mate what version are u using ?

[jjjc_93]

? it works perfect mate what version are u using ?

Always nice to see you round here andressergio. Some great games by Uruguay btw

I'm using Version 4.0

Whenever I go to adjust the CAS or any other timings for that matter, it just reverts back to the last value.

[andressergio]

Always nice to see you round here andressergio. Some great games by Uruguay btw

I'm using Version 4.0

Whenever I go to adjust the CAS or any other timings for that matter, it just reverts back to the last value.

thanks mate after 20 years we are back hope we end on the finals

you must use version 4.1

you can find all latest programs here
http://forums.tweaktown.com/f69/late...y-tools-30530/

give a shot it will work

[invict]

Andresergio can you give me some tips?
I need some settings for a 8400 @ 4500 , 500 fsb 2.4 memory multiplier.
Iam runing ocz reapers @ 1200 @ 5-5-5-15 pl 8 2.3 v
For a Dual core how can obtain the best values for vtt cpu and mch ref ?
I need cpu termination voltage , cpu refrence , and mch reference .
Has i said in advanced settings iam using 900, 900 , 0 ,50 , but iam going crazy because its orthos stable and now in BC2 i get CTD sometimes the sound loops and i get a blue screen and it reboots iam losing all the hope...
All i want its my rig stable at least to play some hours of bad company 2 without problems.
Having to change settings almost everyday is a BIT#H!

[Don_Dan]

Whenever I go to adjust the CAS or any other timings for that matter, it just reverts back to the last value.

tCL can't be changed from Windows.

Other timings should work, even with older versions of MemSet.

[MrDucky]

that are some impressive numbers andre i have a lot less

[andressergio]

tCL can't be changed from Windows.

Other timings should work, even with older versions of MemSet.

yes Don forgot to say that...thanks

[andressergio]

that are some impressive numbers andre i have a lot less

thx mate well i travelled from the ecos to the Gskills PI to elpidas hypers to get those...i should have listened to some mates and i didnt...hypers are a charm

[andressergio]

Andresergio can you give me some tips?
I need some settings for a 8400 @ 4500 , 500 fsb 2.4 memory multiplier.
Iam runing ocz reapers @ 1200 @ 5-5-5-15 pl 8 2.3 v
For a Dual core how can obtain the best values for vtt cpu and mch ref ?
I need cpu termination voltage , cpu refrence , and mch reference .
Has i said in advanced settings iam using 900, 900 , 0 ,50 , but iam going crazy because its orthos stable and now in BC2 i get CTD sometimes the sound loops and i get a blue screen and it reboots iam losing all the hope...
All i want its my rig stable at least to play some hours of bad company 2 without problems.
Having to change settings almost everyday is a BIT#H!

hey mate, BC2 is a MCH stresser, for thight timmings im on 1,52 but before i was on same as you on a quad and needed 1.46MCH

i never had a 45nm so i dunno what refs are but search a few pages back that are posted

what MCH you are on now ?

Cheers
Sergio

[invict]

Iam was using 1.38 for 500 fsb....
Really dunno what to do , what bugs me the most its that the guys that have a e8400 @ 500 fsb posted they´re settings in ET6 and i need bios values....
I bought 2 30mm revoltec fans and seated them in the chipset without cover , and also used MX-3 instead of the hard rock type of paste they use in the chipset , a really nightmare to take off btw...
Iam gonna test now @ 1.44 but i dont have much hope....
The only thing that amuses me its that my Reapers (old ones) are passing memtes96 without prob @ turbo @ 5-5-5-15 @ 2.3 volts coming from a set that cost´s 55€ i must say its pretty good D9 ftw.
Thz mate for the help i post some feedback late this night ....

[andressergio]

Iam was using 1.38 for 500 fsb....
Really dunno what to do , what bugs me the most its that the guys that have a e8400 @ 500 fsb posted they´re settings in ET6 and i need bios values....
I bought 2 30mm revoltec fans and seated them in the chipset without cover , and also used MX-3 instead of the hard rock type of paste they use in the chipset , a really nightmare to take off btw...
Iam gonna test now @ 1.44 but i dont have much hope....
The only thing that amuses me its that my Reapers (old ones) are passing memtes96 without prob @ turbo @ 5-5-5-15 @ 2.3 volts coming from a set that cost´s 55€ i must say its pretty good D9 ftw.
Thz mate for the help i post some feedback late this night ....

Try 1,4 and go slow on MCH...im sure its that

[invict]

I have news, i noticed that in occt the test was called large ffts so i tough well this test is mainly for rams/chipset , so i run orthos cpu test, and didnt get an error , swapped the orthos test to the memory test (large test) and bang error 1 sec!
So the conclusion is that the problem is indeed in the chipset!
Now i changed the strap from 2.4 b (333) to 2.0 (400) hoping that it would relax some timings in the chipset and hell now it passes 4 tests then fail.
So i guess its more stable, btw i forgot to say that i know its the chipset cause the rams pass 4 loops on memtest96 so....
Iam running vtt @ 1.32 pll @ 1.5 cpu ref @ auto mch @ 1.38 mch ref @ 0.726
Advanced: 900 900 0 50...
Going to up volts on mch and rams to see if that helps brb!

[MrDucky]

well andre i have ddr2 but i meant your awesome l2 cache speed cause my speeds are much lower and i also use 500 fsb so does the clockspeed of 4.5 GHz realy make that big diffrence? il post my scores tomorrow oke?

[invict]

So i upped the ram to 2.32 and mch to 2.42 it was passing every test and in the 9th i got bsod !
So iam thinking the mch isnt having enough juice uped to 1.44v lets see how that works!