** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[OC Nub]

I ran blend first at 4500mhz and in 8k it was in the upper 50's c. In Linx it shot to 80c, its a 1.175vid chip and always was hard to cool.
I had the AC on it and still went crazy high in LinX, the newer platforms/chips handle LinX better.
Do you happen to remember the ref's for the e8400's?

Thanks.
Tom

[radaja]

mine liked it like this.with vtt at 1.28v cpu ref at normal(0.760) and mch at 0.750 bios 0.70 ET6

[OC Nub]

Thanks, I will try that, has been a while and couldnt remember.

[OC Nub]

Those ref's work nice, thanks radaja.

This chip has bad sensors idle and load, have no clue what the actual temps are.

Im just using an old 2x1gb kit of dominators.

[radaja]

nice,glad i could help.im sure your temps with the duallie are fine

[OC Nub]

First couple runs were at 4ghz, at 4100mhz now just doing short runs using the 8 multi. The 2gb of mem helps speed things up also, I am sure it requires more vcore with 4gb of mem but this is fast and fun, no 1hr+ runs to see if it passes.



Uploaded with ImageShack.us



Uploaded with ImageShack.us

[andressergio]

First couple runs were at 4ghz, at 4100mhz now just doing short runs using the 8 multi. The 2gb of mem helps speed things up also, I am sure it requires more vcore with 4gb of mem but this is fast and fun, no 1hr+ runs to see if it passes.



Uploaded with ImageShack.us

keep it up Tom those are nice results, hope mazda dont come again lmao

cheers
Sergio

[OC Nub]

LMAO Sergio

I cant seem to get the gflops to go any higher than 27-28 in linx, normally the higher mhz the higher the gflops. This is where I am at now.

I restarted it several times to try and get gflops higher but the same results each time.



Uploaded with ImageShack.us

[OC Nub]

Still working on this chip, failed at 20 passes.



Uploaded with ImageShack.us

[NoGuru]

Try cranking up the MCH OC Nub.

[OC Nub]

I uninstalled the board, the newer boards that recover from a bad oc have ruined me for this platform or at least the older p45's. The boot loops are to frequent, or maybe I have turned into a wimp.

[radaja]

just placed a wanted ad in the wanted section.so i thought id ask you guys too.
im looking for an I/O shield for a UD3P and maybe just maybe,some one heres has
an extra one.i know i went through quite a few of these boards and i used to have
an extra laying around until i gave it to some else who needed it.now i find myself
in a similar situation,i just got a board but didnt get the I/O shield and now need one.
so if any of my fellow UD3P users have an extra please PM me.thanks

EDIT-thanks NoGuru for coming to my aid

[andressergio]

Well guys finally my Stalent 2200 CL8 kit arrived today looks awesome
I want to thank my friend Tracy for the great help

it just outperform my Gskill PI 2000 CL6, it was so easy to tight timmings at stock volts and pass this tests...

X3380@ 4500
Stalent 2200 CL8@ 1600 6-6-6-18 PL7 1,65vdimm stock







cheers
Sergio

[radaja]

andressergio,very nice
so it was easier to do 1600 cl6 whith this kit?
cant wait to see how they can go on the P45
and then how low you can run the latency,cl5?maybe

[zsamz_]

Well guys finally my Stalent 2200 CL8 kit arrived today looks awesome
I want to thank my friend Tracy for the great help

it just outperform my Gskill PI 2000 CL6, it was so easy to tight timmings at stock volts and pass this tests...

X3380@ 4500
Stalent 2200 CL8@ 1600 6-6-6-18 PL7 1,65vdimm stock

[][/URL]

cheers
Sergio

nice but its still a gigabut
try 2000+ cas7

[OC Nub]

Congrats Sergio!

[andressergio]

andressergio,very nice
so it was easier to do 1600 cl6 whith this kit?
cant wait to see how they can go on the P45
and then how low you can run the latency,cl5?maybe

100% easier than Gskills PI 2000 CL6 look this radaja still on stock volts

nice but its still a gigabut
try 2000+ cas7

will try zsamz just cant believe how nice are doing on 1600 PL7 tightening timmings

Congrats Sergio!

Thanks Tom

[andressergio]

just placed a wanted ad in the wanted section.so i thought id ask you guys too.
im looking for an I/O shield for a UD3P and maybe just maybe,some one heres has
an extra one.i know i went through quite a few of these boards and i used to have
an extra laying around until i gave it to some else who needed it.now i find myself
in a similar situation,i just got a board but didnt get the I/O shield and now need one.
so if any of my fellow UD3P users have an extra please PM me.thanks

EDIT-thanks NoGuru for coming to my aid

wow you got the shield ? nice man NoGuru

[andressergio]

still dunno why i cant boot on 2000, was easier on the gskills but tighten timmings at 1600 love it really an amazing kit







cheers
Sergio

[NoGuru]

Lookin good Serg!

No problem radaja, always a pleasure to help a fellow OCer out.

Got my kit today too, nothing to put them in, but they look nice, lol.

[Jor3lBR]

Yep looks promising Sergio congrats!

[andressergio]

Lookin good Serg!

No problem radaja, always a pleasure to help a fellow OCer out.

Got my kit today too, nothing to put them in, but they look nice, lol.

on the wall Trace on the wall its a very good looking kit hope you find a bord to play soon

Sergio

[andressergio]

Yep looks promising Sergio congrats!

Thanks Elano (btw theres a player with your name on BRZ team )

This mem behave fantastic on 1600 PL7 i only had 2 !!! "not convergent on SQR" lol pushing timmings on stock volts

weird thing is i cant boot them at 2000, but gskills at 2000 1T 8-9-8-24 PL8 gave me less bndw than this at 1600 6-6-5-18 PL7 2T lol

either way very happy i will try for 4750 (x9,5) or 4608 (x9) stable now

Cheers my friend
Good luck for Brazil

Sergio

[Hoss331]

You should be able to get the timings even tighter than that, something like 6-6-4-16-52.

[ghost_recon88]

I'm looking at picking up one of these boards andressergio, can you confirm that all the RAM dividers work on it? And can you boot at 1:2 500FSB with the RAM at CL8?

And also whats the max 32M stable FSB you can get out of your quad. You can try lowering to 6x multi if you want.