Geez ... I haven't even tried 0702 ...![]()
Geez ... I haven't even tried 0702 ...![]()
The supplied active NB heat sync is too big to go with my Utra 120 CPU sync. Anyone else doing a guetto cooling system with a 40mm fan?
Right now I'm about 60 degrees at idle, wouldn't mind getting it down a few more degrees.
Yah, I'd pound it with air and keep it open if I didn't need major silence when mixing down audio.
http://www.scythe-usa.com/product/ac...0l_detail.html
This little guy doesn't move allot of air, so I'm thinking it's going to have to be right down flush with the passive sync, offset a bit to avoid the dead spot. Would pull be better in this situation to not push the heat back down on itself?
Last edited by zsamz_; 06-10-2010 at 12:12 PM.
maximus IV extremegtx580
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52vgtx285 ftw sli
OCZ3RPR1866LV6GK hypers
dfi ut p35rampage extreme
gigabut p35c-ds3r![]()
bios suks
gigabut x38-d6qdead thank god
ballistix 8500![]()
1240mhz@2.02v
anyone running this new bios yet? i skipped 0702
is 0704 public release or a beta again?
i like the sound of those extra settings might help with my rig![]()
System Specs
Asus Rampage III Extreme (BIOS 0704) + EK Full Cover Waterblock
Intel i7 920 D0 Stepping, SLBEJ 4.2ghz stable+ EK waterblock
G.Skill Trident 3X2GB Tri Channel 9-9-9-24 @ 9-9-9-24 1N
Sapphire Radeon 5970 @ 850mhz // 1110mhz+ Koolance Waterblock
Nvidia XFX 9600 GSO XXX for Physx
Corsair Obsidian 800D Case
Corsair 1000W Modular PSU
Laing D5 - Waterpump
EK 360 Radiator
Phobya Resovoir
Tygon 1/2"id 3/4"od Clear Tubing
RAID 0 Velociraptors
![]()
Do you have a link where we can find it? I have 0602 and its running fine at 4.3 Ghz
CPU Intel i7 3930k
Motherboard asus Rampage IV extreme with Koolance Block
Memory Corsair Dominator GT 2133 Ghz 16 GB
Graphics Card 3 x ATI Radeon HD 6970 with EK water block
Hard Drive (128 GB Crucial m4) (64 GB Patriot SSD) 1x1500GB
Sound Card Onboard
Power Supply Enermax Revolution 950 W
Case Corsair Obsidian 800D Modded
CPU cooling EK HF Supreme Full Nickel
GPU cooling EK water Block 6970
OS Windows 7 Ultimate x64
bios 704
seems to read the correct volts for cpu in everest ultimate more accurately
when i installed windows re-recognized my cpu, (new microcode?)
seems better than 702....smoother
Last edited by Deboyzfun; 06-10-2010 at 03:30 PM.
Extreme Enthusiast
Rampage III Extreme |Xeon w3690 @ 4.4GHz |CMGTX2 - DOMINATOR GTX 6GB 2133GHz @ 8-8-8-24-1T |
here u go;
http://www.mediafire.com/?g3ncuiagknz
System Specs
Asus Rampage III Extreme (BIOS 0704) + EK Full Cover Waterblock
Intel i7 920 D0 Stepping, SLBEJ 4.2ghz stable+ EK waterblock
G.Skill Trident 3X2GB Tri Channel 9-9-9-24 @ 9-9-9-24 1N
Sapphire Radeon 5970 @ 850mhz // 1110mhz+ Koolance Waterblock
Nvidia XFX 9600 GSO XXX for Physx
Corsair Obsidian 800D Case
Corsair 1000W Modular PSU
Laing D5 - Waterpump
EK 360 Radiator
Phobya Resovoir
Tygon 1/2"id 3/4"od Clear Tubing
RAID 0 Velociraptors
![]()
I just flash from 602 to 704 and My crossfire Setup is now working, I didnt have to make any voltage modification or anything except for vcore. I didnt even touch the IOH voltage (1.19v for crossfire)
Thanx for your help everyone...
CPU Intel i7 3930k
Motherboard asus Rampage IV extreme with Koolance Block
Memory Corsair Dominator GT 2133 Ghz 16 GB
Graphics Card 3 x ATI Radeon HD 6970 with EK water block
Hard Drive (128 GB Crucial m4) (64 GB Patriot SSD) 1x1500GB
Sound Card Onboard
Power Supply Enermax Revolution 950 W
Case Corsair Obsidian 800D Modded
CPU cooling EK HF Supreme Full Nickel
GPU cooling EK water Block 6970
OS Windows 7 Ultimate x64
Newb question ... IOH refers to In Out Hub or the SouthBridge? And ICH refers to Integrated Controller Hub or Northbridge? What controls the PCI-E voltage? In BIOS there are IOH PCI-Ev and ICH PCI-Ev ... which one does what?
PS: Also flashed to 0704 ... ASUS EZ-Flash 2 is the best![]()
Yet another crap retail i7 980x!!!
seriously...
![]()
Just wondering if anyone has a W3570 in there R3E. My w3570 is is a gem batch and it does 4.2 easy as but when i try for 4.4 linx fails going into 2ndpass
I have tried all i can think of but cannot for the life of me get it stable.
My cpu does 4.8 on casecade with 1.3 volts i thought for sure it would do 4.4 on water.
I have even up the cpu volts to 1.4 and nothing
Have aloso tried different multi's
Have even tried 20x210 for 4.2 it wont even do that
I just got the R3E today to replace Gigabyte EX58-EXTREME and I have a big problem with my RAM
It is OCZ Blade DDR3 2000 CL9 (9-9-9-30-2N)
The exact RAM worked fine with the Gigabyte Extreme Mobo but it gives no POST with the R3E , the strangest thing is that it did the same thing with a friend's Asus P6T Vanilla mobo
I can't get the RAM to POST @ 2000 CL9 but it workd fine @ 1600 CL7
With the Gigabyte Mobo I OCed my Core i7 920 to 4.22Ghz and RAM @ 2010 9-9-9-28-1N
Voltages for Gigabyte were :
CPU @ 1.275v
VTT @ 1.555v ( Yes it is high but the Blade RAM would only work at this high VTT Voltage)
DRAM @ 1.66v
With the same settings and voltages, the R3E would not POST with 2000Mhz DDR3
So , I have 2 different Asus mobos that refuse to POST with the same Memory while Gigabyte worked just fine
What can I do ?
I've tried different BIOS settings/ Voltages with the same No POST problem
I've even tried BIOS 0704
Core i7 920 @4.25 with Noctua NH-D14
Asus Rampage III Extreme
6GB Triple Channel OCZ Blade DDR3 2025 9-9-9-24-1T
HD6990+HD6970@950Mhz/6Ghz GDDR5 Tri-Fire
3 BenQ 2420HD 1080p 24" Widescreen LCD in Eyefinity
OCZ Vertex 3 Max IOPS 120GB SSD + Many HDDs !
X-Fi Titanium-Cambridge SoundWorks DTT 3500 Digital
Seasonic X-850
2xBenq 1640 - LiteOn iHAS120-Pioneer 111L - Samsung 203B - NEC Optiarc AD-7200S DVD+/-RW burners
NZXT Phantom Red Edition
Case: M.M Ascension C.S
MB: Asus RIVE
CPU: 3960 24/7: 4900 @1.43v
Ram: 16 gig Dominator Platinum 2133 series ,@2450hmz 10.11.11.28 1.5v
Drive: OCZ RevoDrive 3 X2 240GB
Cooling: 2 x 560 SR1 + 1 X 280 SR1 single loop
Aquaero 5 w/NB PK3 Fans @ 900rpm. Koolance 380i w/. MCP355 x 2 XSPC top
Video: Titan Hydro Copper x 3 SLI
PS: 2 x Corsair 1200w
thanks mate any chance you could do a bios template for me ? Would much appreciate it.
Also what bios are you using.
Thanks
These are no my setting but just a template i grab would you mind editing with what your current bios settings are
Code:
Target CPU Frequency 4410MHz
Target DRAM Frequency 1683MHz
LN2 Mode: Disabled***
QPI Loadline Calibration: Enabled***
Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [21.0]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [21.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Enabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Enabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
----------------------------------------------
BCLK Frequency [210]
PCIE Frequency [100]
DRAM Frequency [1683]
UCLK Frequency [3789]
QPI Link Data Rate [7579]
Memory Configuration Protect [Disabled]
>DRAM Timing Control--------------------------
CAS# Latency 6 [6]
RAS# to CAS# Delay 7 [7]
RAS# PRE Time 6 [6]
RAS# ACT Time 18 [18]
RAS# to RAS# Delay 4 [4]
REF Cycle Time 72 [72]
WRITE Recovery Time 12 [10]
READ to PRE Time 6 [6]
FOUR ACT WIN Time 24 [Auto]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA 60 [60]
Round Trip Latency on CHB 62 [62]
Round Trip Latency on CHC 64 [64]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto]
WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
----------------------------------------------
CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.415 [1.41250]
CPU PLL Voltage 1.812 [Auto]
QPI/DRAM Core Voltage 1.310 [1.31250]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
----------------------------------------------
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
***on-board jumper dependant
xxxxxxxx
OK these are mine .. I am actually using 0531 Bios.. I did not get on with 601/602.. Havnt tried 704 yet.
Sync Mode [Disabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [29.0]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [29.0]
C1E Support [Enabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Disabled]
CPU TM Function [Disabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Disabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Enabled]
Intel(R) C-STATE Tech [Enabled]
C State package limit setting [Auto]
----------------------------------------------
BCLK Frequency [156]
PCIE Frequency [103]
DRAM Frequency [1870]
UCLK Frequency [3789]
QPI Link Data Rate [7579]
Memory Configuration Protect [Disabled]
>DRAM Timing Control--------------------------
CAS# Latency 6 [7]
RAS# to CAS# Delay 7 [7]
RAS# PRE Time 6 [7
RAS# ACT Time 18 [20]
RAS# to RAS# Delay 4 [auto]
REF Cycle Time 72 [auto]
WRITE Recovery Time 12 [auto]
READ to PRE Time 6 [auto]
FOUR ACT WIN Time 24 [Auto]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA 60 [auto]
Round Trip Latency on CHB 62 [auto]
Round Trip Latency on CHC 64 [auto]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto]
WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
----------------------------------------------
CPU Differential Amplitude [900]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [Auto]
Load-Line Calibration [Full]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [1000kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.415 [1.368]
CPU PLL Voltage 1.812 1.812
QPI/DRAM Core Voltage 1.310 [1.337]
DRAM Bus Voltage 1.654 [Auto]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
----------------------------------------------
IOH Voltage 1.244 [Auto]
IOH PCIE Voltage 1.508 [Auto]
ICH Voltage 1.111 [Auto]
ICH PCIE Voltage [Auto]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Case: M.M Ascension C.S
MB: Asus RIVE
CPU: 3960 24/7: 4900 @1.43v
Ram: 16 gig Dominator Platinum 2133 series ,@2450hmz 10.11.11.28 1.5v
Drive: OCZ RevoDrive 3 X2 240GB
Cooling: 2 x 560 SR1 + 1 X 280 SR1 single loop
Aquaero 5 w/NB PK3 Fans @ 900rpm. Koolance 380i w/. MCP355 x 2 XSPC top
Video: Titan Hydro Copper x 3 SLI
PS: 2 x Corsair 1200w
HWbot - Team: XtremeSystems
XS cruncher - Team: XtremeSystems
OCN Feedback
HEAT
*** Being kind is sometimes better then being right.
Thanks needforspeed
Will try that later when i put mt rig back together.
Cpu volts seem high for 24/7 what are max temps we can go on these chips for 24/7?
EDIT
Load-Line Calibration [Full]
CPU Voltage 1.415 [1.368]
You LLC is on FULL doesnt that increase voltage when underload?
Your CPUV is set to 1.425 in Bios and underload it does to 1.368?
When i had my llc on FULL it was increasing Volts under load
Last edited by Ka0sX; 06-10-2010 at 06:25 PM.
Case: M.M Ascension C.S
MB: Asus RIVE
CPU: 3960 24/7: 4900 @1.43v
Ram: 16 gig Dominator Platinum 2133 series ,@2450hmz 10.11.11.28 1.5v
Drive: OCZ RevoDrive 3 X2 240GB
Cooling: 2 x 560 SR1 + 1 X 280 SR1 single loop
Aquaero 5 w/NB PK3 Fans @ 900rpm. Koolance 380i w/. MCP355 x 2 XSPC top
Video: Titan Hydro Copper x 3 SLI
PS: 2 x Corsair 1200w
Unless I read bingo's post incorrectly third party CPUv should be fixed shortly.![]()
Anyone having issues with the board not posting when you make a change in the BIOS?
Every time I change anything, it fails to post. Even if everything is stock and it has nothing to do with overclocking...
maximus IV extremegtx580
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52vgtx285 ftw sli
OCZ3RPR1866LV6GK hypers
dfi ut p35rampage extreme
gigabut p35c-ds3r![]()
bios suks
gigabut x38-d6qdead thank god
ballistix 8500![]()
1240mhz@2.02v
"High Quality is never an accident. It is always the result of excellent intention, intelligent direction, sincere effort and skillful execution. It represents the wisest choice of many alternatives"
System Specs:
R3E + custom 1601 bios / XEON X5650 6-Cores @ 4ghz / G-Skill RipJaws 12GB Kit / Asus Radeon HD EAH5870 / Crucial C300 x 2 R0 + 2 x Samsung 840 Pro's on ICH / Logitech Z-5500 5.1 / Ultra X3 1000w PSU
Water Cooling by:
Swiftech Apogee GTZ / EK FC5870 Acetal+Copper / Swiftech MCP655 / ThermoChill PA120.3 / 6 Gentle Typhoons AP-15 / XSPC Dual Bay Res
PrimoFlex Pro LRT UV Green 1/2" / XSPC Black Chrome Compression Fittings
Misc:
SilverStone TJ07 / 24" Dell UltraSharp / Yadda Yadda lol...
Is this after you flashed to new BIOS or just any change to BIOS settings? Seems strange, but I always set to default settings (F5) before flashing BIOS. I use ASUS EZ-Flash 2. That is the best way to flash BIOS IMO.
Strange thing happened today though. I have my two HD4870x2's in X-fire and when I went to new Catalyst drivers 10.5, I had strange artifacting and then reboot. I did not change voltage in PCI-E after flashing to new 0704 BIOS. I had to remove one video card and remove drivers via hardware device. I then was able to reload new 10.5 drivers and everything is okay. But question is which PCI-E voltage do I change? Southbridge or Northbridge?
Bookmarks