I'm still working on tunning things up a bit, but I thought I'd share progress and see if anyone could offer additional ideas that might help stabalize.
The system runs great, but still BSOD/Reboot under Prime95 within 10 minutes. Temps have cooled off several degrees C, and I gained an additional 100Pts in Passmark score by boosting my RAM just need to stabalize it under load and things will be great.


Here's the BIOS code I'm running
Code:
GIGABYTE GA-EP45T_USB3P
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: AUTO
CPU Clock Ratio ..........................: 9X
Fine CPU Clock Ratio.....................:0.0
CPU Frequency ...........................: 4.05GHz GHz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] []
CPU Host Frequency (Mhz) ............:450Mhz
PCI Express Frequency (Mhz) .........:100Mhz
C.I.A. 2.............................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................:800 mv
PCI Express Clock Drive...................: 900mv
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps
DRAM Performance Control
Performance Enhance....................: [Standard]
Extreme Memory Profile (X.M.P.)........: Auto
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............:3.33D
Memory Frequency (Mhz) ..............: 1500Mhz
DRAM Timing Selectable ................: [Manual] []
Standard Timing Control
CAS Latency Time...............................: 8
tRCD ..........................................: 8
tRP...........................................:  8
tRAS...........................................:  24

Advanced Timing Control [Press Enter]
tRRD...........................................:AUTO
tWTR...........................................: AUTO
tWR............................................: AUTO
tRFC...........................................: AUTO
tRTP...........................................: AUTO
Command Rate (CMD) ............................: AUTO
Channel A

Channel A Timings Settings [Press Enter] 
Static tRead Value......................:Auto
 tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)..................:Auto 
Twr2wr(Different Rank)..................:Auto 
Twr2rd(Different Rank)..................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control................:Auto  ps
Dimm2 Clock Skew Control................:Auto  ps

Channel A Driving Settings [Press Enter] 
Driving Strength Profile:[AUTO]
Data Driving Pull-Up Level.............:Auto 
Cmd Driving Pull-Up Level..............:Auto 
Ctrl Driving Pull-Up Level.............:Auto 
Clk Driving Pull-Up Level..............:Auto 

Data Driving Pull-Down Level...........:Auto 
Cmd Driving Pull-Down Level............:Auto 
Ctrl Driving Pull-Down Level...........:Auto 
Clk Driving Pull-Down Level............:Auto 

Channel B

Channel B Timings Settings [Press Enter] 
Static tRead Value......................:Auto
 tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)..................:Auto 
Twr2wr(Different Rank)..................:Auto 
Twr2rd(Different Rank)..................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control................:Auto  ps
Dimm2 Clock Skew Control................:Auto  ps

Channel B Driving Settings [Press Enter] 
Driving Strength Profile:[AUTO]

Data Driving Pull-Up Level.............:Auto 
Cmd Driving Pull-Up Level..............:Auto 
Ctrl Driving Pull-Up Level.............:Auto 
Clk Driving Pull-Up Level..............:Auto 

Data Driving Pull-Down Level...........:Auto 
Cmd Driving Pull-Down Level............:Auto 
Ctrl Driving Pull-Down Level...........:Auto 
Clk Driving Pull-Down Level............:Auto 


{U]Motherboard Voltage Control{/U]
CPU Vcore….………...........................:1.32500v
CPU Termination…...... 1.200V*...........: 1.3000v
CPU PLL………………….........1.500V*...........: 1.5000v
MCH/ICH
MCH Core……………..........1.100V............: AUTO
MCH Reference..…...….….0.800V............; AUTO
ICH I/O…………....……......1.550V............: AUTO
DRAM
DRAM Voltage ……........1.500V............: 1.6v
DRAM Termination ...…..0.900V............: AUTO
Channel A Data Vref ...0.75V.............: AUTO
Channel B Data Vref ...0.750V............: AUTO
Channel A Address Vref 0.75V.............: AUTO
Channel B Address Vref 0.750V............: AUTO

[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU
Here is a shot under load