Post your C3 Test Results! (new title)

[MaRtIe]

impressive clocks moonman. Such low vcore for those clocks!

[NCspecV81]

this is on a SS.

[MaRtIe]

this is on a SS.

Finally, someone gave me a reason to get a C3 haha. Very ncie!

Whats your idle/load temps on your SS?

[NCspecV81]

Finally, someone gave me a reason to get a C3 haha. Very ncie!

Whats your idle/load temps on your SS?

I don't quite remember but if irc my dt200 reads around -47c on the phenom II. However, what the actual chip was is a mystery to me. If I had to guess I'm saying around -35 to -40c unloaded.

[Oese]

0945EPMW

4ghz 1,456v 1,4v NB

[Moonman]

More superpi lovin




That's it for water cooling. After the new year I'll put it under LN2.

[Zeus]

Awesome CPU-NB speed on that 32M run for just watercooling moonman!

[FlanK3r]

¨whau, nice watter

[Moonman]

Well, it's kind of cheating, water temp around 12 °C

[charged3800z24]

Getting Vanyage higher,

965BE 4.2ghz 2800NB
single 5850 1000c/ 1259m
Orb Compare

[mongoled]

OK managed to get 4400mhz SuperPI done.

Ambient temps around 23C

[dinos22]

Here is my first C3 OC on LN2

thread here > http://www.xtremesystems.org/forums/...d.php?t=242063

[FlawleZ]

Wow dinos22 that's awesome! Will we see sub 10s SP1 from you?

[FlanK3r]

maybe u can get +100MHz at CPU and will see

[neo mike]

The dreaded AMD 1920mgz wall but i finally figured out how to get to the wall, could never get past 1880mgz, keep pushing see what happens. Maybe that AMD master will give me a tip or two.

[chew*]

The dreaded AMD 1920mgz wall but i finally figured out how to get to the wall, could never get past 1880mgz, keep pushing see what happens. Maybe that AMD master will give me a tip or two.

lets see 1m and 32m

[neo mike]

Well i did a quick 1m runs, i can get 1928mgz but it crashes on the 10th loop any tips ? i will do some 32m runs to, but i think heat might be a issue im on air, and its only 50 degrees out. I will turn up the cpu speed some to. I tried to tighten up my timings but it crashes before i hit 1900mgz. I wish i could run cas 6, but thats out of the question with these sticks, and this speed.

[chew*]

Tips for mobo's is mobo specific.....

I no longer have a working MSI, my board that died on water is in RMA atm, my ln2 board lost a dimm slot on air.......I trashed it.

[neo mike]

I have heard the MSI can blow, and take cpus with them. Im still learning about this board, just havent had the time to dedicate to learning enough, but i have never gotten my cpu over 4.350, just my lack of experience, but i will keep trying. Now i have discovered the clock dial on this thing, helps alot.

[Riska]

To go past the 1920 wall on the msi mobo just use 3-10 divider in mem settings aka 1333mhz and raise the HTT then u can go further i went to 1940mhz with my Gskill Eco 1600mhz 7-8-7-24 mem last night but with the 1-4 divider aka 1600mhz i couldent go past 1800mhz at same cl and volt

[neo mike]

Well i think its a wall 1920 on most boards and chips, but Chew just destroyed it, so who knows how high it will go, i bet 2000 is doable. Hey thanks for the tip, i will try that, i could use all the help i can get .

I tried the 3-10 and i got a few more mgz but not much, i think i hit 1930mgz, so not alot of gain, but thanks for the tip. Was your 1940 1m 32m stable ? or just suicide ?.

[Riska]

It was 8m stable 1950 was sucide

[Zeus]

It was 8m stable 1950 was sucide

You know the drill...

Screens or it didn't happen.

[Riska]

that must be another day have just switched to the new gigabyte ud5 board but wil post screens soon

[neo mike]

It was 8m stable 1950 was sucide

I cant get it stable past 1920, i have the GTS 2000 cas 8, you have the ECO gskill 1600 cas 7, and they go that high, wow, looks like those clocks better than my GTS, i cant add anymore voltages , so im guessing you have to play with drive strenghts to get past 1920mgz