aight fellows. i hav'en posted here in awhile picked up a UD3P slaped the Quad 9550 EO to see what it can do here's a shot a 4.2ghz passed IBT vcore set at 1.387v droop to 1.360v...I forgot was the rest of my setting did'nt record them at the tiime and ET6 was'nt install yet.I've been resting at 3.935Ghz for awhile with the vcore at 1.268v set in the (Mit) no problems passing IBT now here also the setting to reach 4.2ghz




50% oc'd





Code:
 MB Intelligent Tweaker(M.I.T.) 

Robust Graphics Booster ..................: Auto
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio......................: +0.5 
CPU Frequency ............................: 4.25Ghz (500x8.5)

Clock Chip Control 
Standard Clock Control 
CPU Host Clock Control....................: [Enabled]
CPU Host Frequency (Mhz) .................: 500
PCI Express Frequency (Mhz) ..............: 101
C.I.A. 2..................................: [Disabled]

Advanced Clock Control 
CPU Clock Drive...........................: 1000mV
PCI Express Clock Drive...................: 1000mV
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps

DRAM Performance Control 
Performance Enhance......................: Turbo
MCH Frequency Latch......................: 333
System Memory Multiplier ................: 2.00B
Memory Frequency (Mhz) ..................: 1066
DRAM Timing Selectable ..................: Manual

Standard Timing Control 
CAS Latency Time.........................: 5
tRCD ....................................: 5
tRP......................................: 5
tRAS.....................................: 18
Advanced Timing Control [Press Enter] 
tRRD.....................................: Auto
tWTR.....................................: Auto
tWR......................................: Auto
tRFC.....................................: Auto
tRTP.....................................: Auto
Command Rate (CMD) ......................: 2T 
Channel A 
Channel A Timings Settings 
Static tRead Value......................: 8

Channel B 
Channel B Timings Settings 
Static tRead Value......................: 8

Motherboard Voltage Control 

Load-Line Calibration.....................: Enabled
CPU Vcore...............1.22500V..........: 1.3875~ under load 1.360 
CPU Termination.........1.200V............: 1.44
CPU PLL.................1.500V............: 1.570v
CPU Reference...........0.760V............: 0.937
MCH/ICH 
MCH Core................1.100V............: 1.50v
MCH Reference...........0.760V............: 0.912v
MCH/DRAM Reference......0.900V............: 0.96v
ICH I/O.................1.500V............: 1.500v
ICH Core................1.100V............: 1.200v
DRAM 
DRAM Voltage............1.800V............: 2.1v
DRAM Termination........0.900V............: 0.86v
Channel A Address Vref..0.900V............: 0.86v
Channel B Address Vref..0.900V............: 0.86v

Advanced Settings 
Limit CPUID Max. to 3.....................: Disabled
No-Execute Memory Protect.................: Disabled
CPU Enhanced Halt (C1E)...................: Disabled
C2/C2E State Support......................: Disabled
x C4/C4E State Support....................: Disabled
CPU Thermal Monitor 2(TM2) ...............: Disabled
CPU EIST Function.........................: Disabled
Virtualization Technology.................: Disabled
__________________

some say...I need to change memory multiplier to 2.00D and test, and also may need to raise my tRead to a 9 is that true? Right...I'm resting at 4.020Ghz at 1.318v droop of 1.296v on the CPU_Z reading here's a shot below



Gaul has incredible results in his out come of Oc'ing at low volts.I wonder is there something.I'm doin wrong to get that? I can't remember what board he got it's not posted in his sign