** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[truehighroller]

Does any body here own GTA IV? If so do you get a stuttering with the game? I know it seems off subject but trust me it's not.

[LifeDrainer]

If i want to run SATA ports in AHCI mode i must enable both "Sata RAID/AHCI Mode" => AHCI Mode and "Onboard SATA/IDE Ctrl Mode" or just "Onboard SATA/IDE Ctrl Mode" => AHCI mode ? 2 HDD's, no RAID function.

[Hoss331]

I usually just select both but it seems to really only require the first one being set to ahci.

[Hardc0r3]

Is sleep function fixed in bios 10 beta series for ep45-ud3p ver 1.0?

[Oztopher]

Thank you sergio ! It wasn't anywhere near stable though, just a screeny.

i.e. your post in the q9650 thread, thanks for that as well ... i won't be scared to put 1.5v+ for MCH and VTT, as long as it is for short term benching...

If i want to run SATA ports in AHCI mode i must enable both "Sata RAID/AHCI Mode" => AHCI Mode and "Onboard SATA/IDE Ctrl Mode" or just "Onboard SATA/IDE Ctrl Mode" => AHCI mode ? 2 HDD's, no RAID function.

I believe the first one is for hard drives only, ACHI is faster than the default. But be warned, for XP you will need to install the ACHI drivers during install...

The second i believe is for optical drives, correct me if i'm wrong? If i set it to ACHI it loads discs faster etc...

----

I have a bit of a problem that i need some help with.

Basically, i can boot 500x8 and run blend for a while (with 1.28vtt, 1.30mch), not tested for thorough stabilty yet, but it runs for a good half an hour or so before i stopped. But, i went back down and tried to make my way up from 485x8, and it seems i can't get it to even run more than 3 tests of blend I tried setting the exact same settings as 500x8 and it still doesn't pass 3 tests, i try more voltage and it makes it worse, i tried less and no difference. I messed with the amps, and skews and still can't pass more than 3 tests...

I then gave up and tried going for 495x8.5 for a 24/7 clock (4.2ghz... 4.2 is 99% stable at 467x9 at the given vcore), but yet again, it doesn't pass more than 3 tests. I tried 500x8.5 with the same settings and it went on for 20mins but i blue screened, it doesn't make sense.

I can get 480x8 stable and 500x8 sort of stable, but 485 to 495fsb seems impossible to get stable...

Any thoughts?

[andressergio]

Thank you sergio ! It wasn't anywhere near stable though, just a screeny.

i.e. your post in the q9650 thread, thanks for that as well ... i won't be scared to put 1.5v+ for MCH and VTT, as long as it is for short term benching...

wellcome mate, you have to keep testing

[radaja]

the Onboard SATA/IDE Ctrl Mode one is for the two purple
sata ports if i remember correctly.the other is the ICH10
intel ports.

[Draculea]

I am really having issues going over 450 FSB with E0 E8600 (Bios 10f)

The build: EP45-UD3P board + 2x2Gb Mushkin DDR2 1100 + E8600
All watercooled, CPU with his own loop.

The settings:

******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [8X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 3.60GHz( 450x8)

********** Clock Chip Control ********

>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [500]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]

>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]

******** DRAM Performance Control ********

Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: 400
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).................: 900
DRAM Timing Selectable (SPD)..........: [Manual]

>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 5]
x tRP.............................5...: [ 5]
x tRAS...........................18...: [15]

>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [4]
x tWTR............................3...: [4]
x tWR.............................6...: [6]
x tRFC...........................52...: [58]
x tRTP............................3...: [4]
x Command Rate (CMD) .............0...: [ 2]

>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [9] or [10]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto

x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto

x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto

>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]

x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto

x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto

>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [9] or [10]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto

x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto

x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto

>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]

x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto

x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto

****** Motherboard Voltage Control ******

Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.45V] real [1.408]
CPU Termination........1.200V.........: [1.300V]
CPU PLL................1.500V.........: [1.59V]
CPU Reference..........0.760V.........: [.745]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.40V]
MCH Reference..........0.760V.........: [.72]
MCH/DRAM Reference.....0.900V.........: [1.05]
ICH I/O................1.500V.........: [1.5V]
ICH Core...............1.100V.........: [1.1V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V] memory is rated 1100 at 1.9V
DRAM Termination.......0.900V.........: [1.05]
Channel A Reference....0.900V.........: [1.05]
Channel B Reference....0.900V.........: [1.05]

Anything over that 455 x 8 is a no post. But as it is now is LINX 20 pass stable. CPU voltage can be much lower @ these settings will go with VID. Which is 1.250.
Memory is well capable of 1200 at 2.2V.
CPU can go 4.5 Ghz on MFII.

I tried all sorts of trial and error tests, read the forum etc. but i am stuck!

So what do you think? Could someone who knows his way with 2-cores give me some input? Thank you!

[stasio]

Read this thread,maybe will help you:
http://forums.tweaktown.com/f69/ga-e...-450fsb-31949/

[Gaul]

o got it to run at 9x512@4608 w/134v but it failed after 59minutes
im going to keep messing with it,i know i can get stable with 1.34v

very NICE chip , with v1.35, my e84 only can touch 4.45 GH





FOR FSB 525 ( 4.75 GH ) can do with v1.36, BUT only 4 Super PI 1 MB.......

[Gaul]

VNB 1.38v, DDR2 1200 5/5/5/15 @ 1.9v


FSB 1200 cl 5/5/5/15 @ 1.90v

[radaja]

Gaul,thanks.looks like youve got a nice one too.
which board is that on?the UD3P?

[pezcore]

471x8.5=4Ghz

MB Intelligent Tweaker(M.I.T.)     
     
Robust Graphics Booster ..................:   Auto
CPU Clock Ratio ..........................:    8
Fine CPU Clock Ratio......................:    +0.5  
CPU Frequency ............................:     4.00Ghz (471x8.5)
      
Clock Chip Control      
Standard Clock Control      
CPU Host Clock Control....................:      [Enabled]
CPU Host Frequency (Mhz) .................:    471
PCI Express Frequency (Mhz) ..............:      100
C.I.A. 2..................................:       [Disabled]

Advanced Clock Control     
CPU Clock Drive...........................:       800mV
PCI Express Clock Drive...................:     900mV
CPU Clock Skew (ps).......................:       0ps
MCH Clock Skew (ps).......................:      0ps
     
DRAM Performance Control      
Performance Enhance......................:  Turbo
MCH Frequency Latch......................:     400
System Memory Multiplier ................:     2.00D
Memory Frequency (Mhz) ..................:       950
DRAM Timing Selectable ..................:     Manual

Standard Timing Control     
CAS Latency Time.........................:     5
tRCD ....................................:     5
tRP......................................:      5
tRAS.....................................:       15
Advanced Timing Control [Press Enter]      
tRRD.....................................:     Auto
tWTR.....................................:      Auto
tWR......................................:       Auto
tRFC.....................................:     Auto
tRTP.....................................:    Auto
Command Rate (CMD) ......................:  2T   
Channel A      
Channel A Timings Settings       
Static tRead Value......................:   12

Channel B      
Channel B Timings Settings       
Static tRead Value......................:  12
      
Motherboard Voltage Control      

Load-Line Calibration.....................:      Disabled
CPU Vcore...............1.22500V..........:     1.41250v
CPU Termination.........1.200V............:       1.30v
CPU PLL.................1.500V............:     1.570v
CPU Reference...........0.760V............:     0.863v
MCH/ICH      
MCH Core................1.100V............:   1.36v
MCH Reference...........0.760V............:  0.863v
MCH/DRAM Reference......0.900V............:      0.96v
ICH I/O.................1.500V............:     1.500v
ICH Core................1.100V............:     1.100v
DRAM      
DRAM Voltage............1.800V............:  2.1v
DRAM Termination........0.900V............:      0.96v
Channel A Address Vref..0.900V............:      0.96v
Channel B Address Vref..0.900V............:      0.96v

Advanced Settings      
Limit CPUID Max. to 3.....................:       Disabled
No-Execute Memory Protect.................:     Enabled
CPU Enhanced Halt (C1E)...................:       Disabled
C2/C2E State Support......................:  Disabled
x C4/C4E State Support....................: Disabled
CPU Thermal Monitor 2(TM2) ...............: Disabled
CPU EIST Function.........................: Disabled
Virtualization Technology.................: Enabled 

Thank you all for your help.

Thanks for posting this. I copied and got to the same 4GHz easily. I lowered the vCore a little (1.39) and left the thermal monitors and C1 stuff enabled.

Unless someone has something better I'll stick with this config. Thanks again!

[truehighroller]

Here is mine.




MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ..................: Auto
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio......................: +0.5
CPU Frequency ............................: 4.00Ghz (500x8.5)

Clock Chip Control
Standard Clock Control
CPU Host Clock Control....................: [Enabled]
CPU Host Frequency (Mhz) .................: 500
PCI Express Frequency (Mhz) ..............: 101
C.I.A. 2..................................: [Disabled]

Advanced Clock Control
CPU Clock Drive...........................: 1000mV
PCI Express Clock Drive...................: 1000mV
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps

DRAM Performance Control
Performance Enhance......................: Turbo
MCH Frequency Latch......................: 333
System Memory Multiplier ................: 2.40D
Memory Frequency (Mhz) ..................: 1200
DRAM Timing Selectable ..................: Manual

Standard Timing Control
CAS Latency Time.........................: 5
tRCD ....................................: 5
tRP......................................: 5
tRAS.....................................: 18
Advanced Timing Control [Press Enter]
tRRD.....................................: Auto
tWTR.....................................: Auto
tWR......................................: Auto
tRFC.....................................: Auto
tRTP.....................................: Auto
Command Rate (CMD) ......................: 2T
Channel A
Channel A Timings Settings
Static tRead Value......................: 8

Channel B
Channel B Timings Settings
Static tRead Value......................: 8

Motherboard Voltage Control

Load-Line Calibration.....................: Enabled
CPU Vcore...............1.22500V..........: 1.3875~ under load 1.344
CPU Termination.........1.200V............: 1.44
CPU PLL.................1.500V............: 1.570v
CPU Reference...........0.760V............: 0.937
MCH/ICH
MCH Core................1.100V............: 1.50v
MCH Reference...........0.760V............: 0.912v
MCH/DRAM Reference......0.900V............: 0.96v
ICH I/O.................1.500V............: 1.500v
ICH Core................1.100V............: 1.200v
DRAM
DRAM Voltage............1.800V............: 2.0v
DRAM Termination........0.900V............: 0.86v
Channel A Address Vref..0.900V............: 0.86v
Channel B Address Vref..0.900V............: 0.86v

Advanced Settings
Limit CPUID Max. to 3.....................: Disabled
No-Execute Memory Protect.................: Disabled
CPU Enhanced Halt (C1E)...................: Disabled
C2/C2E State Support......................: Disabled
x C4/C4E State Support....................: Disabled
CPU Thermal Monitor 2(TM2) ...............: Disabled
CPU EIST Function.........................: Disabled
Virtualization Technology.................: Disabled

[Hoss331]

Thanks for posting this. I copied and got to the same 4GHz easily. I lowered the vCore a little (1.39) and left the thermal monitors and C1 stuff enabled.

Unless someone has something better I'll stick with this config. Thanks again!

Those figures look ok but I would suggest dropping PL to 9 or 10 and PLL to 1.50 since these boards overvolt pll.

[pezcore]

Ok I changed PLL to 1.5v

What's PL?

I'm also curious to know why CPU-Z reports Core Voltage at an almost constant 1.424v when I had it set to 1.39 (and just lowered it to 1.38, still no change)

Anything else I could lower?

[Circaflex]

Here are my settings on my board with a q6600 and a single stage, anything i should change or anything too high on volts? this is just my first play with overclocking on this board, hopefully i can get to 4.4 or 4.5ghz. What should i set me memory to? These new settings on this board confuse me a little.

The settings:

******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.05GHz( 450x9)

********** Clock Chip Control ********

>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [450]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]

>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]

******** DRAM Performance Control ********

Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: 333
System Memory Multiplier (SPD)........: [2.00C]
Memory Frequency(Mhz).................: 1080
DRAM Timing Selectable (SPD)..........: [Auto]



****** Motherboard Voltage Control ******

Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.5]
CPU Termination........1.200V.........: [1.38]
CPU PLL................1.500V.........: [1.61]
CPU Reference..........0.760V.........: [.914]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.34]
MCH Reference..........0.760V.........: [.914]
MCH/DRAM Reference.....0.900V.........: default
ICH I/O................1.500V.........: [1.570V]
ICH Core...............1.100V.........: [1.200V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.18V]

Everything else auto or default

[Allubz]

nvm

[Hoss331]

Ok I changed PLL to 1.5v

What's PL?

I'm also curious to know why CPU-Z reports Core Voltage at an almost constant 1.424v when I had it set to 1.39 (and just lowered it to 1.38, still no change)

Anything else I could lower?

PL on this board is Static tRead. Im not sure why your reported vcore would be higher than the bios setting, should be several steps lower than bios/et6.

Can anyone list fitting watercooling options for the UD3P:
MOSFET
Northbridge
Southbridge

I don't care about:
CPU
The NB has excellent stock cooling
There's no need to cool MOSFETs

Thanks in advance!

I use an EK 5 for the northbridge.

[Gaul]

Gaul,thanks.looks like youve got a nice one too.
which board is that on?the UD3P?

thanx....up sory e84 with ASUS P5Q, just 4 compare u'r mighty chip...

but the ddr 1200 use UD3R

[Oztopher]

I found out the reason why anything inbetween 480fsb and 500fsb wasn't stable... it was RAM. Strange...

It seems so picky with what timings can be set. At 467fsb with ram at 1868mhz 8-8-8-22, trfc 59, it ran blend overnight (8hours or so), using custom 3200mb of memory. But at 485fsb with 1940mhz on ram, the timings needed to be set to 10-10-10-28, trfc 84, to at least run blend for 10mins (i didn't test further). Yet 500fsb with ram at 2000mhz, with 8-8-8-24, trfc 84, it ran for an hour.... the ONLY thing different was that cmd rate was at 1n, which i can't set myself, it never sticks when i set in bios, only at 500+ it auto sets to 1n.

Is there something i'm missing with DDR3? I'm not too familier with RAM overclocking, i always thought it was pretty straight forward Can anyone share their experiences and tips with DDR3? i would really appreciate it

Oz

[gurusan]

Oztopher I am struggling on my ddr3 board as well, what are your complete settings including GTL refs?

[Circaflex]

Hey guys so I have a gigabyte e45-ud3p and an intel q6600 quad SLACR. I need some help with overclocking on the unit. I am on Phase change for the CPU cooling wise. With 2 spot cools over the NB and the RAM. I have a bench table, so everything is open air cooling also.

My Questions:

What are the safe voltage areas for my particular setup? Am I safe where I am at now? Can i go higher in some areas?(See Log of Settings)

What are some settings I can try for my memory. I dont quite understand the ratios anymore and Im not sure if the few attempts ive had BSOD because ive set memory to high or something. I have GSKILL F2-8500CL5D-4GBPI PC2-8500 5-5-5-15 2.1.

Is there anything you can see in my settings that I should change?

The settings:

******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.05GHz( 450x9)

********** Clock Chip Control ********

>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [450]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]

>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]

******** DRAM Performance Control ********

Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: 333
System Memory Multiplier (SPD)........: [2.00C]
Memory Frequency(Mhz).................: 1080
DRAM Timing Selectable (SPD)..........: [Auto]



****** Motherboard Voltage Control ******

Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.5]
CPU Termination........1.200V.........: [1.38]
CPU PLL................1.500V.........: [1.61]
CPU Reference..........0.760V.........: [.914]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.4]
MCH Reference..........0.760V.........: [.914]
MCH/DRAM Reference.....0.900V.........: default
ICH I/O................1.500V.........: [1.570V]
ICH Core...............1.100V.........: [1.200V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.18V]

Everything else auto or default

[Oztopher]

Oztopher I am struggling on my ddr3 board as well, what are your complete settings including GTL refs?

Hey mate, these are my settings so far for 467x9: (8hours or so stable on prime blend) Obviously some things will be different depending on how good ur chip, board and ram are.


MB Intelligent Tweaker(M.I.T.)


Robust Graphics Booster ...................: Auto
CPU Clock Ratio ...........................: 9x
Fine CPU Clock Ratio.......................: --
CPU Frequency .............................: 4203Mhz

Clock Chip Control

Standard Clock Control
CPU Host Clock Control.....................: [Enabled]
CPU Host Frequency (Mhz) ..................: 467Mhz
PCI Express Frequency (Mhz) ...............: 101
C.I.A. 2...................................: Disabled

Advanced Clock Control
CPU Clock Drive............................: 800mv
PCI Express Clock Drive....................: 900mv
CPU Clock Skew (ps)........................: 0ps
MCH Clock Skew (ps)........................: 0ps

DRAM Performance Control

Performance Enhance........................: [Turbo]
(G)MCH Frequency Latch.....................: [333]
System Memory Multiplier ..................: 4.00B
Memory Frequency (Mhz) ....................: 1868Mhz
DRAM Timing Selectable ....................: [Manual]

Standard Timing Control
CAS Latency Time...........................: 8
tRCD ......................................: 8
tRP........................................: 8
tRAS.......................................: 22

Advanced Timing Control [Press Enter]
tRRD.......................................: 4
tWTR.......................................: 4
tWR........................................: 8
tRFC.......................................: 59
tRTP.......................................: 4
Command Rate (CMD) ........................: Auto

Channel A Timings Settings [Press Enter]

Static tRead Value.........................:7
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:Auto
Twr2wr(Different Rank).....................:Auto
Twr2rd(Different Rank).....................:Auto
Trd2wr(Same/Diff Rank).....................:Auto
Dimm1 Clock Skew Control...................:+200 ps
Dimm2 Clock Skew Control...................:Auto ps
DDR Write Training ........................: Disabled
DDR Write Leveling ........................: Disabled

Channel A Driving Settings [Press Enter]

Driving Strength Profile...................:Auto

Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto

Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto

Channel B Timings Settings [Press Enter]

Static tRead Value.........................:7
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:Auto
Twr2wr(Different Rank).....................:Auto
Twr2rd(Different Rank).....................:Auto
Trd2wr(Same/Diff Rank).....................:Auto
Dimm1 Clock Skew Control...................:+200 ps
Dimm2 Clock Skew Control...................:Auto ps
DDR Write Training ........................: Disabled
DDR Write Leveling ........................: Disabled

Channel B Driving Settings [Press Enter]

Driving Strength Profile...................:Auto

Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto

Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto


Motherboard Voltage Control


Voltage Type.………... Normal

CPU
Load Line Calibration......................: [Enabled]
CPU Vcore....................1.225v........: v 1.38750
CPU Termination….............1.200V*.......: v 1.24
CPU PLL......................1.500V*.......: v 1.50
CPU Reference................0.760V*.......: v 0.785
MCH/ICH
MCH Core.....................1.100V........: v 1.24
MCH Reference................0.800V........: v 0.785
MCH/DRAM Ref.................0.750V........: v 0.940
ICH I/O......................1.50V.........: v 1.50

DRAM
DRAM Voltage.................1.500V........: v 1.90
DRAM Termination.............0.750V........: v 0.940
Channel A Data Reference.....0.750v........: v 0.940
Channel B Data Reference.....0.750v........: v 0.940
Channel A Address Reference..0.750v........: v 0.940
Channel B Address Reference..0.750v........: v 0.940

Advanced Settings

HDD S.M.A.R.T. Capability..................: [Disabled]
CPU Multi-Threading........................: [Enabled]
Limit CPUID Max. to 3......................: [Disabled]
No-Execute Memory Protect..................: [Disabled]
CPU Enhanced Halt (C1E)....................: [Disabled]
CPU Thermal Monitor 2(TM2) ................: [Disabled]
CPU EIST Function..........................: [Disabled]
Virtualization Technology..................: [Disabled]

[Regalia87]

Can someone give me some info please, I want to know if its possible to run this memory cooler with the UD3P mobo without any clearance issues with the heatsinks

http://www.newegg.com/Product/Produc...82E16835116021