No clue, I wonder IF the voodoo can beat PURE Bios tuning + crap SP1 limited to airOriginally Posted by Don_Dan
Your score with just high-clocked memory in the first post is really fast, I never managed to do this during my testing. I didn't reach that high clocks though, even my best score is lacking some MHz on core, NB and memory.
BUT: Where will clocked RAM plus voodoo land...
P.S. you should try out 3d05 at stock and then clocked ram only
Last edited by chew*; 09-30-2009 at 11:26 AM.
heatware chew*
I've got no strings to hold me down.
To make me fret, or make me frown.
I had strings but now I'm free.
There are no strings on me
I will get at it tomorrow!
4142MHz Core and >3000MHz NB will be very tough with my CPU, but I'll try it!
![](http://www.hwbot.org/signature/u15466.png height="110" )
MOAR fans and coolingI will get at it tomorrow!
4142MHz Core and >3000MHz NB will be very tough with my CPU, but I'll try it!MOAR I say
heatware chew*
I've got no strings to hold me down.
To make me fret, or make me frown.
I had strings but now I'm free.
There are no strings on me
Will get some cable ties and more fans tomorrow!
Ok So I thought I would note this.
Corsair or any other manufacturers If you ever do release an AMD kit,( I know Corsair does have one on the Site that is not available yet etc coming soon).
Please use an alternative heatspreader solution.....With a popular heatsink such as the TRUE 120 there are obviously clearance issues.
It will likely save you RMA's from stubborn users making it fit and AMD users aggravation.
For obvious reasons I have swapped to my Xigamatek 1284.
Last edited by chew*; 09-30-2009 at 12:23 PM.
heatware chew*
I've got no strings to hold me down.
To make me fret, or make me frown.
I had strings but now I'm free.
There are no strings on me
offtopicOk So I thought I would note this.
Corsair or any other manufacturers If you ever do release an AMD kit,( I know Corsair does have one on the Site that is not available yet etc coming soon).
Please use an alternative heatspreader solution.....With a popular heatsink such as the TRUE 120 there are obviously clearance issues.
It will likely save you RMA's from stubborn users making it fit and AMD users aggravation.
For obvious reasons I have swapped to my Xigamatek 1284.
This new AMD Socket AM2 / AM3 Bolt-Thru-Kit Rev.2 help you and all ultra120 users fit heat sink normally:
http://www.thermalright.com/new_a_pa...btk_rev2.htm#2
http://www.heatsinkfactory.com/therm...kit-rev-2.html
http://www.performance-pcs.com/catal...ducts_id=26375
CPU : AMD X2 5200+ @ 3Ghz
Motherboard : EPOX EP-AF590 SLI2 with Thermalright HR-05 IFX SLI
CPU Cooler : Thermalright Ultra 120 Extreme with Noctua NF-P12
Videocard : XFX 8600GT Fatal1ty Edition @ 700/1800Mhz
DDR : Teem Xtreem PC-6400 2X1GB @ 4-4-4-8 / 500Mhz
HDD : Sata II - 2 X Seagate 250GB ST3250410AS 16MB cach in RAID 0 ; IDE - Seagate 160GB, WD 80GB
PSU : Chieftec 600 Watt, +12V Combined 48A - CTF-600-14CS
CASE : Chieftec AEGIS CX-05B-B with 4 X Scythe SLIP STREAM SY1225SL12M controled by
Scythe Kaze Master 5.25 @ 1000RPM; 3 X Noctua NF-B9 @ 1000RPM
Monitor : HP L1740
speacker : Logitech X-230
I have the "scissors" for intel....I will pass.
My heatsink does not budge I will pass on that, plus spending more money.......when the solution is simple, smaller heatspreader thus cheaper costs to them = cheaper for consumer.
Secondly........with that setup my sanyo will chop up the memory.........pointing towards back of case........so only other option is blow hot air at ram and into my case......
Last edited by chew*; 09-30-2009 at 01:04 PM.
heatware chew*
I've got no strings to hold me down.
To make me fret, or make me frown.
I had strings but now I'm free.
There are no strings on me
Posting Permissions
Reply With Quote
Bookmarks