** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[The Viper]

huh, ok, thanks guys...has anyone been able to run PL8 on 2.4B divider at or above 500FSB?

EDIT: Can someone tell me on what page the templates for 4.5GHz are, I know Ive seen a couple

[Jor3lBR]

huh, ok, thanks guys...has anyone been able to run PL8 on 2.4B divider at or above 500FSB?

EDIT: Can someone tell me on what page the templates for 4.5GHz are, I know Ive seen a couple

Most of us run 2:40>Turbo>PL8>4500Mhz.


Just posted what you want over Q9650 thread, just click on my link.

[ViViD]

Hi Guys

Can Somone Give Me Some Information

I Can Set Ram Frquency To 1438Mhz Realy Realy Hard This Link

And I Know Divider 3:5 Is Bug On Giga P45 Set 1568Mhz This Link But This Cheat 1410 Mhz Realy

I Need To Know My Fault To Get More Frquency Many Other My Friends Can Set 1500 Mhz With That Moudle Ram

Some Bios Setting:

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:
PCI Express Frequency (Mhz) .........:Auto
C.I.A. 2......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 1000mv
PCI Express Clock Drive.................: 900mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 4.00B
Memory Frequency (Mhz) ..............: 1,333Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time..........................: 6
tRCD ...........................................: 6
tRP..............................................: 6
tRAS............................................: 18
Advanced Timing Control [Press Enter]
tRRD...........................................:Au to
tWTR..........................................:Aut o
tWR............................................:Au to
tRFC...........................................:70
tRTP...........................................:4
Command Rate (CMD) ....................:Auto

Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value.........................:10
tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment..................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)...................:10
Twr2wr(Different Rank)..................:10
Twr2rd(Different Rank)..................:10
Trd2wr(Same/Diff Rank).................:11
Dimm1 Clock Skew Control.............:Auto ps
Dimm2 Clock Skew Control.............:Auto ps
DDR Write Training .....................: Auto
Channel A Driving Settings [Press Enter]
Driving Strength Profile...................:Auto

Data Driving Pull-Up Level...............:Auto
Cmd Driving Pull-Up Level................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto

Data Driving Pull-Down Level...........:Auto
Cmd Driving Pull-Down Level............:Auto
Ctrl Driving Pull-Down Level.............:Auto
Clk Driving Pull-Down Level..............:Auto
Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value.........................: 10
tRD Phase0 Adjustmen....................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment ..................:Auto
tRD Phase3 Adjustment...................:Auto
Trd2rd(Different Rank).....................:10
Twr2wr(Different Rank).....................:10
Twr2rd(Different Rank).....................:10
Trd2wr(Same/Diff Rank)....................:11
Dimm1 Clock Skew Control...................:Auto ps
Dimm2 Clock Skew Control...................:Auto ps
DDR Write Training .........................: Auto
Channel B Driving Settings [Press Enter]
Driving Strength Profile...................:Auto

Data Driving Pull-Up Level.................:Auto
Cmd Driving Pull-Up Level..................:Auto
Ctrl Driving Pull-Up Level.................:Auto
Clk Driving Pull-Up Level..................:Auto

Data Driving Pull-Down Level...............:Auto
Cmd Driving Pull-Down Level................:Auto
Ctrl Driving Pull-Down Level...............:Auto
Clk Driving Pull-Down Level................:Auto

CPU
Load Line Calibration......................: [Enabled]
CPU Vcore...................................:1.500v
CPU Termination…..... 1.200V*........:1.700v
CPU PLL...............1.500V*.............:1.75 v
CPU Reference.........0.755V*..........:Auto

MCH Core..............1.100V................: 1.64v
MCH Reference.........0.800V..............: Auto
MCH/DRAM Ref..........0.900V...............:Auto
ICH I/O.................1.50V...............: Auto
ICH Core............……1.100V...............:Auto
DRAM
DRAM Voltage..........1.800V...............: 2.7v It's Too High I Know But Worked
DRAM Termination......0.900V...............: Auto
Channel A Reference...0.900V...............:Auto
Channel B Reference...0.900V...............:Auto
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3......................: [Disabled]
No-Execute Memory Protect..................: [Disabled]
CPU Enhanced Halt (C1E)....................: [Disabled]
C2/C2E State Support.......................: [Disabled]
x C4/C4E State Support.....................: [Disabled]
CPU Thermal Monitor 2(TM2) ................: [Disabled]
CPU EIST Function..........................: [Disabled]
Virtualization Technology..................: [Disabled]

I'm Use Water Chiller For CPU And All Other On AIR

NB Too Hot Ram Warm But Not Bad
This SPD My Ram:

[rubber5]

Try just setting your CPU voltage to 1.35 and your chipset to 1.4 and then your memory to 2.1 and leave everything else auto except the performance level and your memory strap. All of your gtls at auto at first. Mine I have noticed this for a fact now after having this motherboard for about a week now that if I set the gtls my self at first it won't boot, leave them at auto and vualua boot.

I also noticed that if I leave my memory at 1.8v it won't boot either. I think the motherboard thinks because the memory is running at 1150MHz it needs 2.1 and it won't let me boot with out it set to that. Kind of a weird thing but, whatever the memory is running cool at that voltage any way. Hope that helps.

Once you get a feel for what to set the volts to the lowest possible volts, then start setting your gtls one by one checking for stability every time you make a change until you have everything else manually set as well.

ok thanks pal i will try it the other thing is what is the max temp you would push out of these cpus i dont want to burn it out i would like to keep the rig for at least 4 years if you know what i meen and i have the cpu voltage set to 1.18v and it can hit 63c with intel burn test and i think it was about 58 with prime so if i take it to 1.35 i kow it will go well over 80c what do you think

[Gameman]

Hi folks, I intend to invest in a UD3P/UD3R Gigabyte board and just had a quick question...
Are the
UD3P and the UD3R basically the same board with different slot configuarations etc...or does one clock higher than the other

Also this is important....Has anybody ever NOT been able to break 471??? (minimum Q9550 fsb for 4.0 GHZ) on either of these two boards???? or is 475-530 pretty much consistent????

Cause I be gettin' this strictly for the Quad benefit

otherwise I got the two other X48's

I wanna take a Q9550 to 4.0 - maybe 4.2 GHZ
Also I need something to do this Fall......

Thanks

[nkresho]

Hi folks, I intend to invest in a UD3P/UD3R Gigabyte board and just had a quick question...
Are the
UD3P and the UD3R basically the same board with different slot configuarations etc...or does one clock higher than the other

Also this is important....Has anybody ever NOT been able to break 471??? (minimum Q9550 fsb for 4.0 GHZ) on either of these two boards???? or is 475-530 pretty much consistent????

Cause I be gettin' this strictly for the Quad benefit

otherwise I got the two other X48's

I wanna take a Q9550 to 4.0 - maybe 4.2 GHZ
Also I need something to do this Fall......

Thanks

IMO, and I have a bit of experience here. The boards will clock the same. If you're not planning on running crossfire, the r will definitely do it for you.

You'll need to talk to ocnub about the q9550. He's had his well over 4000mhz. I'm sure he'll be by here before too long to give his input

[truehighroller]

You gotta feel it out a lot with this motherboard that is for sure, that is it takes some effort but, it is worth it once you unleash it's power and get all your settings set. . I just now settled at 485 x 8.5 because I am on air right now, and that is about all my Thermalright Extreme can really handle TBH. I have already begun piecing together what I will be purchasing, then I can have some more fun. I say get the board, I did.

[tool_462]

I've run 2 different Q9550's in my UD3P, as well as numerous dual cores and a Q9650, none had ANY issue at all getting 500+ FSB 24/7 stable, all with 8GB installed :up;

[truehighroller]

I've noticed the chipset gets pretty warm on my motherboard as well with this one compared to my P5Q Deluxe that I was running. This chipset is almost as if they tweaked the hell out of it or I guess they could of just got high binned north bridges. It is a very good board though IMO.

[Swordsman]

Hi. Would Thermalright IFX-14 cooler fit the GA-UD3P without any problems?

[1Tanker]

Hi. Would Thermalright IFX-14 cooler fit the GA-UD3P without any problems?

According to TR's site, it should fit ok.

http://www.thermalright.com/new_a_pa...cl.htm#asusp45

[rubber5]

hi guys to anyone that is overclocking there quads over 1ghz how can you tell of your north brige and south brige is NOT overheating.
Is there anything you can use to check the temps becuse everest tells me its rinning at 55c but it does not change when under load

THANKS GUYS

[Earzz]

Hi guys just a quick question, whats the differnce betweent the rev 1.0 and 1.1 GA-EP45-UD3P?
I can buy a used one and that is a 1.0 so that why im asking, thanks.

[truehighroller]

ok thanks pal i will try it the other thing is what is the max temp you would push out of these cpus i dont want to burn it out i would like to keep the rig for at least 4 years if you know what i meen and i have the cpu voltage set to 1.18v and it can hit 63c with intel burn test and i think it was about 58 with prime so if i take it to 1.35 i kow it will go well over 80c what do you think

You should probably look in to lapping your TRUE (Heatsink). I would also consider lapping your CPU. Make sure it is a keeper first though, before lapping the CPU that is because it will then be yours forever unless you sell it on Ebay.

I am going to lap mine now I know I have a good one. Temp wise, I am pushing 81C with my 9550 with Intel Burntest. Nothing else will get it above 65C - 70C so I am not concerned with this. I would aim for temps around there mate.

[zsamz_]

well i didnt put my true on my q9650
my 26$ cool master 212 slaped it -4-8c

[truehighroller]

well i didnt put my true on my q9650
my 26$ cool master 212 slaped it -4-8c

Maybe I should get one .

[zsamz_]

Maybe I should get one .

forgot to say
cool room 212 is better 20-24c
hot room true is better
the 212 is verry sensitive to ambient temps and needs a second fan
to be honest i wished i bought 2 more to replace my true and my sons v8

[thebluemeanie1]

Hi guys just a quick question, whats the differnce betweent the rev 1.0 and 1.1 GA-EP45-UD3P?
I can buy a used one and that is a 1.0 so that why im asking, thanks.

The rev 1.1 has the northbridge heatsink flipped to allow for more CPU cooler compatibility. It also ships with F6 BIOS instead of F4.

Has any one gotten over 556 FSB using a quad on a rev 1.1? The most I've gotten to boot from mine is 550.

[1Tanker]

The rev 1.1 has the northbridge heatsink flipped to allow for more CPU cooler compatibility. It also ships with F6 BIOS instead of F4.

Has any one gotten over 556 FSB using a quad on a rev 1.1? The most I've gotten to boot from mine is 550.

I can boot fine @ 533(sometimes 534), but that's with a C1 9550/air. Probably more a limitation of the chips' stepping, than the mobo.

edit: oops, sorry...mines rev 1.6

[Earzz]

The rev 1.1 has the northbridge heatsink flipped to allow for more CPU cooler compatibility. It also ships with F6 BIOS instead of F4.

Thank you for your answer but i think ill skip the buy then, looking into a new one but it looks like the board is EOL.
Only 3 shops still got it in the Netherlands

[rubber5]

You should probably look in to lapping your TRUE (Heatsink). I would also consider lapping your CPU. Make sure it is a keeper first though, before lapping the CPU that is because it will then be yours forever unless you sell it on Ebay.

I am going to lap mine now I know I have a good one. Temp wise, I am pushing 81C with my 9550 with Intel Burntest. Nothing else will get it above 65C - 70C so I am not concerned with this. I would aim for temps around there mate.

thanks for that but what do you meen if its a keeper i cant afford to replase it so i will be keeping it ps how do you know if you have a good chip i get confused on how to tell.
If i run the cpu @80c in intel burn test how long will it last or will i only get a couple of years out of it i really need it to last me to be honnest but i do know if its at stock speeds its good for at least 10 years

[nkresho]

Argh. Guys I think I made a big boo boo.

I got my heatkiller 3.0 today and I installed it immediately. So I pull the old sink, clean everything, and I install the heatkiller, fill the loop and turn it on.

tttt tick ttt tick ttick . Wierd sound coming from near cpu area..... no boot, no signal to monitor, nothing.

I turn off the fans one by one to make sure they're not doing it.

tttttick tt tick tick tick tttt tick ttttick

All fans off, still making the noise.

So I listen closer and determine it's coming from the cpu area.

Fail...

Long story short, I apparently installed the heatkiller backplate backwards.

I'm figuring that the backplate was making something short on the back of the cpu area. Even with the rubber pad.

In my defense, the rubber pad sort of snaps in place on the wrong side of the backplate. I thought it felt right so I popped it on that way.

Big mistake.

SO... I re-installed the backplate and got everything back in order. I reset cmos by pulling the battery. I powered it up.

Stock settings run fine

My overclocks no longer are stable above 4.0ghz. It won't boot at all over 4.2, with my previous settings.

So, I just ordered another ud3r from newegg. It should be here monday next week.

stupid me, should have taken my time. Heatkiller instructions didn't say or show which way it went, but I blame myself.

[Slyr7.62]

resho, that's unfortunate. Hope you have fun with your "new" UD3R.

[gugle]

for frontal sound work, have to do something?
bios or something?

plugged into the motherboard, but does not recognize when plugged the headset and microphone on the front

[nkresho]

make sure your case's connector has all the right pins in it. there's one called "sense" I think. IIRC it's a green wire (but I may be totally off)

Also, there should be a setting in your hd audio setup (red colored speaker at bottom right of desktop) I can't remember exactly what it's called, but something one the lines of "auto detect front panel" something or other.

You are using the "hd" audio plug right? I don't know anything about the ac97 stuff.

HTH