here's my new blade 9200's.
a custom run from 2048 - 4096, set to run FFT's in place
a full blend for 8hour
& a run of everest
i set these up the night i got them but havnt been able to post up till today
here's my new blade 9200's.
a custom run from 2048 - 4096, set to run FFT's in place
a full blend for 8hour
& a run of everest
i set these up the night i got them but havnt been able to post up till today
c2d e8500 q822a536
x38-t2r LT bios 10/2
ocz blade 9200 2x 2Gb
4890 sapphire catalyst 9.7
3x samsung spinpoint p120 250Gb 2xraid0 stripe 16k
pioneer dvr216
850w silverstone st85f
akasa omega
swift storm
swift mcw-30
1x 240mm thermochill & 1x 120mm rads
mcp-655 pump
dell 2407wfp
windows xp pro x64
My 9200 blades seem to want more than 1.80v to run at their rated speeds. Anybody else experiencing this?
Does this sound right if i'm at 1.840v for 1147mhz. Timings are 5-5-5-18-60-2t, pl 8.
For 1135 it was fine with 1.8... with the same timings
This is using memtest 2.11.
Also, am I going to lead my ram to an early death by running at 1.84?
Thnx.
where are u reading the voltage from?
c2d e8500 q822a536
x38-t2r LT bios 10/2
ocz blade 9200 2x 2Gb
4890 sapphire catalyst 9.7
3x samsung spinpoint p120 250Gb 2xraid0 stripe 16k
pioneer dvr216
850w silverstone st85f
akasa omega
swift storm
swift mcw-30
1x 240mm thermochill & 1x 120mm rads
mcp-655 pump
dell 2407wfp
windows xp pro x64
1.84v from bios or from sensor?Originally Posted by nkresho
because your motherboar has a little vdrop on ram, 1.8v from bios is 1.76 real...
i7 4770k @ 4.4GHz | MSI MPower | 8gb Geil Evo Corsa 2133 | Gigabyte GTX670 wf3 | Samsung 830 256gb | 3xWd Re3 raid5 | Antec HCG 620w
Θ Core i7 4770k 4.4ghz 1.3v :'( Θ Core i7 2600k 4.5ghz 1.344v Θ E8400 500x8 4ghz 1.36v Θ Core i7 860 @ 4ghz 1.328v Θ Turion M500 2.2ghz 1.025v Θ Phenom II 955 c3 3.91ghz 1.52v Θ Phenom II 545 3.77ghz 1.47v Θ
_~{ ALL RS }~_
I was wondering about that. That is a bios setting. So hopefully I'm right where I want to be.
I'll have to find the mobo read points and check it with my dmm.
Last edited by nkresho; 08-12-2009 at 03:29 PM.
you can read a REAL value of ddr voltage with everest, in sensor page (vdimm voce )
Last edited by devil_mcry; 08-12-2009 at 03:47 PM.
i7 4770k @ 4.4GHz | MSI MPower | 8gb Geil Evo Corsa 2133 | Gigabyte GTX670 wf3 | Samsung 830 256gb | 3xWd Re3 raid5 | Antec HCG 620w
Θ Core i7 4770k 4.4ghz 1.3v :'( Θ Core i7 2600k 4.5ghz 1.344v Θ E8400 500x8 4ghz 1.36v Θ Core i7 860 @ 4ghz 1.328v Θ Turion M500 2.2ghz 1.025v Θ Phenom II 955 c3 3.91ghz 1.52v Θ Phenom II 545 3.77ghz 1.47v Θ
_~{ ALL RS }~_
dling now thank you.
Ok, well easytune6 hwmonitor says the ram is getting 1.856
Everest says 1.86
Bios is set to 1.84.
So my board is overvolting a little bit.
Then my question stands. Do you guys think it's safe to run it at this volatge, long term? It's at stock speed right now, 1150mhz.
OCZ EVP (Extended Voltage Protection) is a feature that allows performance enthusiasts to use a VDIMM of 1.85V without invalidating their OCZ Lifetime Warranty.
however i don't know why your motherboard overvolt your ram , other user haver -0.04v vdroop :| ... i don't know i don't have your motherboard sorry ... but i think it's safe run your ram at 1.856v...
i7 4770k @ 4.4GHz | MSI MPower | 8gb Geil Evo Corsa 2133 | Gigabyte GTX670 wf3 | Samsung 830 256gb | 3xWd Re3 raid5 | Antec HCG 620w
Θ Core i7 4770k 4.4ghz 1.3v :'( Θ Core i7 2600k 4.5ghz 1.344v Θ E8400 500x8 4ghz 1.36v Θ Core i7 860 @ 4ghz 1.328v Θ Turion M500 2.2ghz 1.025v Θ Phenom II 955 c3 3.91ghz 1.52v Θ Phenom II 545 3.77ghz 1.47v Θ
_~{ ALL RS }~_
Exactly I wanted to hear. Thanks.
Those should do 1.9v without issue. Just put a finger on them to check the temp.
http://valid.canardpc.com/show_oc.php?id=643273
Do you fold?
SuperPi 1M 10.984s @ 4.25GHz
Cool Blue
Gigabyte EP45-UD3P Rev 1.1
E8400 E0 @ 4.1 GHz
Zalmann 9500
2x2GB GSkill 9600 5-5-5-15 1212 MHz 2.1v PL8
9600GSO (I'm a folder, not a gamer)
Corsair VX550 80Plus
WD 500GB SATA3
Antec 900
Yup, or you could also put an Antec Spot Cooler on them just to make sure they don't run hot
Intel i7 950 D0 @ 4Ghz 23x175
-Cooled by: Prolimatech Megashadow
EVGA Classified E760
G.Skill Perfect Storm DDR3-2133 3x2GB @ 1745 8-8-8-20
MSI 5850 Twin Frozr 1GB DDR5
1 300GB WD Velociraptor WD3000HLFS
1 1TB Western Digital WD1002FAEX
2 2TB WD WD20EARS
Corsair HX850W
Coolermaster HAF 932
They don't. Try it.
http://valid.canardpc.com/show_oc.php?id=643273
Do you fold?
SuperPi 1M 10.984s @ 4.25GHz
Cool Blue
Gigabyte EP45-UD3P Rev 1.1
E8400 E0 @ 4.1 GHz
Zalmann 9500
2x2GB GSkill 9600 5-5-5-15 1212 MHz 2.1v PL8
9600GSO (I'm a folder, not a gamer)
Corsair VX550 80Plus
WD 500GB SATA3
Antec 900
i got a 120mm yate loon sitting above my chips, ziptied it to sum of my tubing. havnt touched them to see how hot they get tho.
c2d e8500 q822a536
x38-t2r LT bios 10/2
ocz blade 9200 2x 2Gb
4890 sapphire catalyst 9.7
3x samsung spinpoint p120 250Gb 2xraid0 stripe 16k
pioneer dvr216
850w silverstone st85f
akasa omega
swift storm
swift mcw-30
1x 240mm thermochill & 1x 120mm rads
mcp-655 pump
dell 2407wfp
windows xp pro x64
They don't feel warm while priming. Although they do have a 120mm med yate loon blowing across them from about 8 inches away.
That's good to hear, incase I get a bit brave.Those should do 1.9v without issue. Just put a finger on them to check the temp.
The Platinums do run a little hotter though, I have a temp sensor in between the PCB and heatspreader in the middle of the PCB, idle is around 34c and load they will reach 46c. (No airflow over them...)
Though, the heatspreaders aren't *too* hot. (This is at 1.85v)
If putting 1.9v in them I'd put a fan over them, but I wouldn't worry about the Blades too much, they have a huge heatsink. I bought the 1150 Plats because I needed a low profile.
Smile
Blade that disappeared, only to have Amazon, and is expensive
Anybody know any place that has more to sell it?
Sorry my bad EnglishLanguage Tools
http://www.google.com.br/language_tools?hl=pt-BR
Q9550 | Gigabyte GA-EP45-UD3P (rev. 1.1) | 4x1GB | SLI 98GTX | LC8850 750w
4685.99 Mhz (H20) - http://valid.canardpc.com/show_oc.php?id=689328
WC - CPU Swiftech Apogee GTZ | Enzotech SNBW | VGA Koolance VID-398 | Rad MagiCool 360ST | Pump DP-1200 | MCRES-Micro Rev2.
PGN use to have them (9600's), but have since sold out.
Smile
Looks like Amazon has them @ ~$105, still $45-$55 cheaper than the G.Skill's.
There is a reason it says "Usually ships within 1 to 3 months."
In 1 to 3 months you will get a refund
Smile
Doh! So used to seeing 1-3 days I just assumed rather than read the whole thing.
It seems to be 1.8v 9200 kits are gone forever, the best I can see is 9200 2.2v kits.
"Prowler"
X570 Tomahawk | R7 3700X | 2x16GB Klevv BoltX @ 3600MHz CL18 | Powercolor 6800XT Red Devil | Xonar DX 7.1 | 2TB Barracuda | 256GB & 512GB Asgard NVMe drives | 2x DVD & Blu-Ray opticals | EVGA Supernova 1000w G2
Cooling:
6x 140mm LED fans, 1x 200mm LED fan | Modified CoolerMaster Masterliquid 240
Asrock Z77 thread! | Asrock Z77 Extreme6 Review | Asrock P67 Extreme4 Review | Asrock P67 Extreme4/6 Pro3 thread | Asrock Z68 Extreme4 thread | Asrock Z68 Extreme4 Review | Asrock Z68 Gen3 Thread | 8GB G-Skill review | TK 2.ZERO homepage | P5Q series mBIOS thread
Modded X570 Aorus UEFIs
Newegg still has them:http://www.newegg.com/Product/Produc...Z%20Technology
http://valid.canardpc.com/show_oc.php?id=643273
Do you fold?
SuperPi 1M 10.984s @ 4.25GHz
Cool Blue
Gigabyte EP45-UD3P Rev 1.1
E8400 E0 @ 4.1 GHz
Zalmann 9500
2x2GB GSkill 9600 5-5-5-15 1212 MHz 2.1v PL8
9600GSO (I'm a folder, not a gamer)
Corsair VX550 80Plus
WD 500GB SATA3
Antec 900
what chips are these ocz ?
how do they scale with voltage above 2.0v and CL4 ?
Elpida
Not worth a dam.
These top out about 1.9-1.95v
They are binned by voltage.
Cas4 results have been 900-1000 MHz
http://valid.canardpc.com/show_oc.php?id=643273
Do you fold?
SuperPi 1M 10.984s @ 4.25GHz
Cool Blue
Gigabyte EP45-UD3P Rev 1.1
E8400 E0 @ 4.1 GHz
Zalmann 9500
2x2GB GSkill 9600 5-5-5-15 1212 MHz 2.1v PL8
9600GSO (I'm a folder, not a gamer)
Corsair VX550 80Plus
WD 500GB SATA3
Antec 900
Posting Permissions
Reply With Quote
Bookmarks