The E0 Q9550 SLB9V thread (finally!)

[Sonic9]

Q9550 C1 @ 460x8.5=3,92Ghz (1,320v cpuz / pll 1,60v / vtt 1,40v) @ P5E Rampaged Intel X38 , vnb 1,45v, strap 333, ai booster=lighter, pl=10 , gtl @ auto , 2x2Gb OCZ FlexII @ 1105Mhz 5/5/5/15/auto@2,10v

Here screenshot @ 468x8.5@1,312v but occt doesn't pass , play with hight voltages & gtl & tweaks , nothing more , I think x38 stop here with quad ...
with my old e8400 e0, playing wih 520x8

ps: now I'm play with noctua nh-u12p , 90° with linx ... with my old xp90 temps are hotter , like ~136° ;-)

[spinejam]

You may be able to use PL9 with Frequency Latch 400-200d.

yep, thanks for the tip! faster everest memory benchmarks w/ pl=9.

[OC Nub]

yep, thanks for the tip! faster everest memory benchmarks w/ pl=9.

Nice man.

[ViViD]

My Q9550 E0 In 481*8.5 With Zalman CPNS9700LED Pass Every Test As Well
Other Setting In Auto+2.2 Volt For DDR Voltage+C1E Disabled

[spinejam]

what's the highest o/c you've seen w/ these Q9550's (air-cooling)?

[monza1412]

what's the highest o/c you've seen w/ these Q9550's (air-cooling)?

Ive seen 4200/4300 overclocks with some good batches.

[OC Nub]

what's the highest o/c you've seen w/ these Q9550's (air-cooling)?

On the Gigabyte UD3/UD3R/UD3P thread, check out PangingIII's OC's with the q9550, pretty high Clocks.

[INFRNL]

what's the highest o/c you've seen w/ these Q9550's (air-cooling)?

I am currently running a Q9550 @ 4.25ghz @ 1.3ish v's (would have to double check) I havent played with it much. Have been running 100% load on all cores 24/7 for months now. Been running WCG and F @ H non-stop for a few months now.

I think If I played with it; I could get it higher. Load temps are in the 50* range.

I am using a gigabyte UD3P and 4gig kit of Mushkin ram; oh this is with an OCZ Vendetta 2 HSF.

[Fguarezi]

My Q9550 E0 - L844B

Prime 2:30hs



Linx 1024 com 20 loops



Linx 2048 - 1.24v

[monza1412]

Meus parabéns Fguarezi

Nice clock with low volts.

could you please post your complete batch number?

[Fguarezi]

Meus parabéns Fguarezi

Nice clock with low volts.

could you please post your complete batch number?

Valeu

Batch not remember, do not write .

[OC Nub]

Put my q9550 back in to play with some more, ran this today.

[monza1412]

Put my q9550 back in to play with some more, ran this today.

awesome chip man, congratz for you too

What is your highest stable speed? 4250/4300mhz?


you should change your nickname btw ... jk

[OC Nub]

Thanks, 4250mhz-1.35v bios is my max so far, temps get to warm to go higher on air.

[spinejam]

very nice o/c OC Nub!

[OC Nub]

Thanks man.

[monza1412]

this is what I have achieved so far...




My motherboard has maxed out at this point (P35 chipset). Soon I will be jumping to the ud3p wagon, so hopefully I will get better clocks for sure.

[OC Nub]

Nice OC Monza, great vcore also.

[andressergio]

Thanks, 4250mhz-1.35v bios is my max so far, temps get to warm to go higher on air.

nice run mate

Cheers
Sergio

[monza1412]

Nice OC Monza, great vcore also.

thanks buddy

[OC Nub]

nice run mate

Cheers
Sergio

Thanks andressergio.

[ViViD]

Hi Some Bench With My Quad



3D Mark Vantage>>> 15810


3D Mark 03>>>>>>> 81608


3D Mark 06>>>>>>> 24307


Aqua Mark>>>>>>> 171080


But i'm Never Stable Over 500 FSB Any Sugestion For Over 500 FSB Just For CPU Frquency Take Shot In CPUZ
I Use Water Cooling And My IDLE Temp 5C

[andressergio]

Hi Some Bench With My Quad



3D Mark Vantage>>> 15810


3D Mark 03>>>>>>> 81608


3D Mark 06>>>>>>> 24307


Aqua Mark>>>>>>> 171080


But i'm Never Stable Over 500 FSB Any Sugestion For Over 500 FSB Just For CPU Frquency Take Shot In CPUZ
I Use Water Cooling And My IDLE Temp 5C

Nice numbers vivid

Cheers
Sergio

[OC Nub]

Hi Some Bench With My Quad

But i'm Never Stable Over 500 FSB Any Sugestion For Over 500 FSB Just For CPU Frquency Take Shot In CPUZ
I Use Water Cooling And My IDLE Temp 5C

Very nice vivid!!
I am not familair with that motherboard, I had to adjust the clock skew to get 500fsb stable on the UD3P but I stopped there, my temps get to high to keep pushing.

[ViViD]

Nice numbers vivid

Cheers
Sergio

Very nice vivid!!
I am not familair with that motherboard, I had to adjust the clock skew to get 500fsb stable on the UD3P but I stopped there, my temps get to high to keep pushing.

Tanx Friends
I Try On End OF Each Week Test And Try And Try
I Hope Can Get 25K On 3D 06
Here's My Resualt On Week 2 Of Lord OverClocking
http://www.futuremark.com/community/...ional09/week2/

In End List