X48 Rampage Formula Preview.

[Ghostleader]

Probably, what´s about the rest of volt and GTL settings?

Please show us, it´s easier to help then.

[DaLiu]

Probably, what´s about the rest of volt and GTL settings?

Please show us, it´s easier to help then.

I have a problem with my rig, i have a Rampage Formula with Q9450 and 2 x 2 GB OCZ at 1150 Mhz running for more than 1 year perfect overclocket at 3600 Mhz with 1,28 V in bios (real around 1,26 V with LCC enabled). From yesterday i started to get freeze on games and i tried to check the system using Prime95, Linx and Intel Burn Test. With Prime95 on Blend everything was fine for more than 2 hours, i checked the memory with memtest and everything looks just fine, when im doing Small FFS a core is failing after 15-20 min, Intel Burn Test and Linx is failing after 3-4 loops, do you think i need to give a little more voltage to my cpu?

My settings:

*Extreme Tweaker*
Ai Overclock Tuner [Manual]
CPU Ratio Setting [08]
FSB Strap to North Bridge [Auto]
FSB Frequency [450]
PCIE Frequency [100]

DRAM Frequency [DDR2-1140MHz]
DRAM Command Rate [2N]
DRAM CMD Skew on Channal A [Greyed Out]
DRAM CMD Skew on Channal B [Greyed Out]
DRAM CLK Skew on Channal A [Delay 300ps]
DRAM CLK Skew on Channal B [Delay 300ps]

DRAM Timing Control [Manual]
1st Information
CAS# Latency [5]
RAS# to CAS# Delay [5]
RAS# PRE Time [5]
RAS# ACT Time [15]
RAS# to RAS# Delay [3]
REF Cycle Time [65]
WRITE Recovery Time [6]
READ to PRE Time [3]
2nd Information
READ to WRITE Delay (S/D) [8]
WRITE to READ Delay (S) [3]
WRITE to READ Delay (D) [5]
READ to READ Delay (S) [4]
READ to READ Delay (D) [6]
WRITE to WRITE Delay (S) [4]
WRITE to WRITE Dealy (D) [6]
3rd Information
WRITE to PRE Delay [14]
READ to PRE Delay [5]
PRE to PRE Delay [1]
ALL PRE to ACT Delay [6]
ALL PRE to REF Delay [6]

DRAM Static Read Control [Enabled]
Ai Clock Twister [Moderate]
Ai Transation Booster [Manual]
Common Performance Booster [7]

Pull-In of CHA PH1 [Disabled]
Pull-In of CHA PH2 [Disabled]
Pull-In of CHA PH3 [Disabled]
Pull-In of CHA PH4 [Disabled]
Pull-In of CHA PH5 [Disabled]
Pull-In of CHA PH6 [Disabled]
Pull-In of CHB PH1 [Disabled]
Pull-In of CHB PH2 [Disabled]
Pull-In of CHB PH3 [Disabled]
Pull-In of CHB PH4 [Disabled]
Pull-In of CHB PH5 [Disabled]
Pull-In of CHB PH6 [Disabled]

CPU Voltage [1.2850]
CPU PLL Voltage [1.60]
North Bridge Voltage [1.55]
DRAM Voltage [2.16]
FSB Termination Voltage [1.32]
South Bridge Voltage [1.05]
SB 1,5V Voltage [1.50]
Loadline Calibration [Enabled]
CPU GTL Voltage Reference [Auto]
NB GTL Voltage Reference [Auto]
DRAM Controller Voltage REF [AUTO]
DRAM Channel A Voltage REF [AUTO]
DRAM Channel B Voltage REF [AUTO]

CPU LED Selection [CPU Voltage]
NB LED Selection [North Bridge Voltage]
SB LED Selection [South Bridge Voltage]
Voltiminder LED [DISABLED]

CPU Spread Spectrum [Disabled]
PCIE Spred Spectrum [Disabled]
CPU Clock Skew [Normal]
NB Clock Skew [Normal]


*Advanced settings*
CPU Ratio Setting [08]
C1E Support [Disabled]
CPU TM Function [AUTO]
Vanderpool Technology [Disabled]
Execute Disable Bit [Enabled]
Max CPUID Value Limit [Disabled]
Intel(R) SpeedStep (TM) Tech. [Disable]


I used this settings for more than 1 year with problems till yesterday.