the multiplier dropping issue only affected by LinX, I haven't come across any application or game that could put such tremendous stress on the cpu that forces it to drop (not even when I was converting 35GB of RAW data the other day), cpu load was 100% on all 8 threads but mutliplier remain at 21x. So I'd say ignore it for now till Asus put their act together to fix it so we can run LinX more comfortably
Core i7 920 D0 3844A717 4.40Ghz HT on @1.36v (LinX/Prime/3D stable), Corsair 850W, 12GB OCZ Platinum 1600, P6T Deluxe V2, EVGA GTX 285 SS, OCZ Vortex SSD 30GB x3 RAID0, HAF 932.
Water Cooling Setup: XSPC RX360, MCP355 + XSPC Res Top, Swiftech GTZ, 1/2" Tygon, Scythe S-Flex SFF21F push, 20mm yateloon D12SL-12C pull.
Opteron 148 CABNE 0528 GPMW 3.1Ghz @1.6v Prime Stable. Westy 37" LVM-37W3, DFI Venus 975, 2GB TeamX Cronus Micron, GSkill HZ, Sapphire X1900XTX, Zippy 700W, X-Fi Xtrememusic, 36GB Raptors x2 @Raid-0.
WC Setup: PA120.3 +Shroud, MCP655, STORM, MCW60, 1/2" Tygon, mini res, Yate Loon.
Is the following an isolated case?
My V2 P6T-D decided not to recognize the 3x2gb RAM anymore, it instead told I have 2gb RAM. I am sure that all 3 sticks are good.
Yahh, same thing when I am using WCG, the multy stays at x21Originally Posted by ben805
the multiplier dropping issue only affected by LinX, I haven't come across any application or game that could put such tremendous stress on the cpu that forces it to drop (not even when I was converting 35GB of RAW data the other day), cpu load was 100% on all 8 threads but mutliplier remain at 21x. So I'd say ignore it for now till Asus put their act together to fix it so we can run LinX more comfortably
PC: Intel Core i7 920 D0 | Kingston Hyperx T1 6GB 2000Mhz 8-8-8 RAM | Foxconn Bloodrage GTI | Sapphire 4870X2 | Perc 5/i - WD 640AAKSx4 RAID0 | Asus 2014L1T | Dell 2407WFP | Lian Li G70 Silver Watercooled
WaterCooling: Q˛ Project by The-Fox
CPU Loop: Swiftech Apogee GTZ | Feser X-Changer 480 | Swiftech MCP655 Vario w/ DetroitAC top | EK Multioption RES 250 Rev.2 | Tygon R3603 1/2" | YL D12SL@1350RPM x4
GPU Loop: EK-FC4870 X2 Nickel | Swiftech MCR320 | Swiftech MCP655 Vario w/DetroitAC top | EK Multioption RES 150 Rev.2 | Tygon R3603 1/2" | YL D12SL@1350RPM x3
Is your ram on the QVL list ?
Un-plug the power supply, take out the battery and one sick of memory. Replace and see if your bios is fully re-set.My V2 P6T-D decided not to recognize the 3x2gb RAM anymore, it instead told I have 2gb RAM. I am sure that all 3 sticks are good.
Intel Core i7 LGA1366 - 3.60GHz (20x 180 BCLK) / 4 Cores / 8 Threads / 1.26v / UCLK 3067MHz / QPI 6.47 GTs
Crucial, Micron D9JNM ICs, 12GB DDR3 - 1440MHz, 8-8-8-20 1T, 1.6v, Tri-Channel
Palit NVIDA GeForce GTX 460 1GB DDR5 16x 2.0 - GPU 750MHz / Shader 1500Hz / DDR5 3625MHz
2x Intel X25-M G2, 80GB SSD, ICH10R RAID 0 / Windows 7 Professional 64-bit
....... System Runs 24/7....... system_01
No, I think Asus has a standalone acpi driver.
I had this when I was using the p965 deluxe (forgot the exact model name).
The strange thing on the p6t deluxe v2 is the driver is not in the download section.
yes, I did that. Still only 2gb known to BIOS.
Its basically the same board as the Deluxe v1 other than lack of SAS controller, acpi driver should be common between them.
Regardless it should have been included with the driver CD...
Work Rig: Asus x58 P6T Deluxe, i7 950 24x166 1.275v, BIX2/GTZ/D5
3x2048 GSkill pi Black DDR3 1600, Quadro 600
PCPower & Cooling Silencer 750, CM Stacker 810
Game Rig: Asus x58 P6T, i7 970 24x160 1.2v HT on, TRUE120
3x4096 GSkill DDR3 1600, PNY 660ti
PCPower & Cooling Silencer 750, CM Stacker 830
AMD Rig: Biostar TA790GX A2+, x4 940 16x200, stock hsf
2x2gb Patriot DDR2 800, PowerColor 4850
Corsair VX450
Can someone post a link to the ACPI driver for the V1? I can't seem to find it, and I too have the unknown device in device manager.
Also, I was looking at the drivers on Asus' website, and it seems that there are Marvell SATA drivers. I have never installed any Marvell SATA drivers, because I thought that the SATA ports were from the ICH10R... no? It seems to work fine without them, are they really needed?
Asus Rampage II Gene | Core i7 920 | 6*2GB Mushkin 998729 | BFG GTX280 OCX | Auzentech X-Fi Forte | Corsair VX550
—Life is too short to be bound by the moral, ethical and legal constraints imposed on us by modern day society.
[QUOTE=003;3774996]Can someone post a link to the ACPI driver for the V1? I can't seem to find it, and I too have the unknown device in device manager.
Also, I was looking at the drivers on Asus' website, and it seems that there are Marvell SATA drivers. I have never installed any Marvell SATA drivers, because I thought that the SATA ports were from the ICH10R... no? It seems to work fine without them, are they really needed?[/QUO
Go to windows update it will automatically install it for you.
To get rid of the "unknown device" in device manager put the Asus motherboard DVD in the drive. When autoplay pops up click run the cd. The Asus driver gui will appear and the unknown device disappears in the device manager. No need to install any driver manually it will disappear once the Asus screen appears. (Have the device manager open at the same time).
I thought everyone knew that, it works on any Asus board, ive been doing it that way for a few years on X58/X38/P35 and even my AMD780 board. Works on Gigabyte too at least an x38 board i had.
With the Marvell thing the motherboard has ports for marvell and Intel. On the P6T standard the marvell ports are a different color. (2 Marvell 6 Intel)
Just plug in to the intel ports and disable marvell in the bios that way you dont have the marvel screen during bootup. No need for Marvel drivers.
Asus Z87 DeluxeDual/ i7 4770K @4.4Ghz /4x4 Gb Corsair Dominator 1866Mhz 9-9-9-24 1T/Intel 520 240Gb SSD /Samsung F3 1TB HD/MSI 680 Lightning / Corsair AX850 watt PSU/Thermalright Ultra Extreme 120/Samsung S23A950D 120Hz monitor/ Aurora 570 Case//Windows 7 64bit/AudioEngineA2 Speakers/Gigabyte Osmium Aivia Mechanical KB/ Gigabyte Krypton Mouse
Anyone running a 920 with 218bclk x 21 multi or higher. I seem to be stuck here and would appreciate some help.
What are the max bclks reported on these boards?
I don't want the drivers from the Asus CD because they are out of date. And the ones on their website are usually out of date as well. Typically, motherboard "specific" drivers are really not specific at all, and are just out dated repackaged drivers from the manufacturer of the component in question.
I would like to know who actually makes the "unknown device" component and where the latest driver can always be obtained.
Also, regarding the Intel vs Marvell SATA ports on the P6T Deluxe... would I be correct to assume that the two vertical ports are on the Marvell controller and the horizontal ones are on the Intel controller (other than the Marvell SAS ports)?
Asus Rampage II Gene | Core i7 920 | 6*2GB Mushkin 998729 | BFG GTX280 OCX | Auzentech X-Fi Forte | Corsair VX550
—Life is too short to be bound by the moral, ethical and legal constraints imposed on us by modern day society.
is there the possibility to use 22x to all the cores on this board? how should I set the bios? thank's for the answers
do you ave a 965 Nehalem?is there the possibility to use 22x to all the cores on this board? how should I set the bios? thank's for the answers
Intel Core i7 LGA1366 - 3.60GHz (20x 180 BCLK) / 4 Cores / 8 Threads / 1.26v / UCLK 3067MHz / QPI 6.47 GTs
Crucial, Micron D9JNM ICs, 12GB DDR3 - 1440MHz, 8-8-8-20 1T, 1.6v, Tri-Channel
Palit NVIDA GeForce GTX 460 1GB DDR5 16x 2.0 - GPU 750MHz / Shader 1500Hz / DDR5 3625MHz
2x Intel X25-M G2, 80GB SSD, ICH10R RAID 0 / Windows 7 Professional 64-bit
....... System Runs 24/7....... system_01
With an unlocked cpu (965) yes otherwise no other than for a single core turboboosted.is there the possibility to use 22x to all the cores on this board? how should I set the bios? thank's for the answers
Work Rig: Asus x58 P6T Deluxe, i7 950 24x166 1.275v, BIX2/GTZ/D5
3x2048 GSkill pi Black DDR3 1600, Quadro 600
PCPower & Cooling Silencer 750, CM Stacker 810
Game Rig: Asus x58 P6T, i7 970 24x160 1.2v HT on, TRUE120
3x4096 GSkill DDR3 1600, PNY 660ti
PCPower & Cooling Silencer 750, CM Stacker 830
AMD Rig: Biostar TA790GX A2+, x4 940 16x200, stock hsf
2x2gb Patriot DDR2 800, PowerColor 4850
Corsair VX450
No, the marvell controller will work as sas or sata.
Work Rig: Asus x58 P6T Deluxe, i7 950 24x166 1.275v, BIX2/GTZ/D5
3x2048 GSkill pi Black DDR3 1600, Quadro 600
PCPower & Cooling Silencer 750, CM Stacker 810
Game Rig: Asus x58 P6T, i7 970 24x160 1.2v HT on, TRUE120
3x4096 GSkill DDR3 1600, PNY 660ti
PCPower & Cooling Silencer 750, CM Stacker 830
AMD Rig: Biostar TA790GX A2+, x4 940 16x200, stock hsf
2x2gb Patriot DDR2 800, PowerColor 4850
Corsair VX450
The device is ATK0110 ACPI Utility.
The version in the cd is 1043.2.15.37 dated 8/13/2004 so I suppose it is quite old.
They have one dated 2006. But, I don't think there is any difference. You would think ASUS would atleat update the driver date. Even if it was just for looks. I received it from MS Updates. But, if you search "Utilities" on the ASUS site, one comes up dated after 04.
Did you try un-installing the error devices an then scan for new hardware. That should work.
Last edited by chuckbam; 05-07-2009 at 04:31 PM.
Intel Core i7 LGA1366 - 3.60GHz (20x 180 BCLK) / 4 Cores / 8 Threads / 1.26v / UCLK 3067MHz / QPI 6.47 GTs
Crucial, Micron D9JNM ICs, 12GB DDR3 - 1440MHz, 8-8-8-20 1T, 1.6v, Tri-Channel
Palit NVIDA GeForce GTX 460 1GB DDR5 16x 2.0 - GPU 750MHz / Shader 1500Hz / DDR5 3625MHz
2x Intel X25-M G2, 80GB SSD, ICH10R RAID 0 / Windows 7 Professional 64-bit
....... System Runs 24/7....... system_01
I have heard that there is the possibility to mod the bios to allow to all the cores 22x and I need to find it to try..obviously I have got i7 920
Ah, so then Marvell has one unified driver for the SAS and SATA ports? Where can I get the latest version of it? Also, is there a way to simply disable the Marvell SAS/SATA ports in the BIOS, but leave the Marvell PATA port enabled (for optical drive)? Are there any special drivers for the Marvell PATA controller?
Ok I did some searching and it appears that ATK stands for AsusTek and the ATK0110 is a chip that allows the Asus Ai Booster program to work in Windows and overclock the system. So since it is an Asus device, the latest driver should in fact come from Asus. What is the latest version they have and where can we get it?
OMG!!! That would be nuts!!!I have heard that there is the possibility to mod the bios to allow to all the cores 22x and I need to find it to try..obviously I have got i7 920If there is a way to do this guys, we need to find it!!
Asus Rampage II Gene | Core i7 920 | 6*2GB Mushkin 998729 | BFG GTX280 OCX | Auzentech X-Fi Forte | Corsair VX550
—Life is too short to be bound by the moral, ethical and legal constraints imposed on us by modern day society.
Ok I did some searching and it appears that ATK stands for AsusTek and the ATK0110 is a chip that allows the Asus Ai Booster program to work in Windows and overclock the system. So since it is an Asus device, the latest driver should in fact come from Asus. What is the latest version they have and where can we get it?
Wow, that is great that you now know what ATK stands for. You must be new to ASUS Motherboards. I posted a pic of the latest version. Or, like I said, you can get it on the ASUS support download site by searching utilities.
All OS versions here: http://chuckbam.com/Post2/ACPI_1043400.rar
.
Last edited by chuckbam; 05-09-2009 at 12:22 AM.
Intel Core i7 LGA1366 - 3.60GHz (20x 180 BCLK) / 4 Cores / 8 Threads / 1.26v / UCLK 3067MHz / QPI 6.47 GTs
Crucial, Micron D9JNM ICs, 12GB DDR3 - 1440MHz, 8-8-8-20 1T, 1.6v, Tri-Channel
Palit NVIDA GeForce GTX 460 1GB DDR5 16x 2.0 - GPU 750MHz / Shader 1500Hz / DDR5 3625MHz
2x Intel X25-M G2, 80GB SSD, ICH10R RAID 0 / Windows 7 Professional 64-bit
....... System Runs 24/7....... system_01
Directly from the horse's (Asus') mouth.
1, "Intel(R) ICH10R LPC Interface Controller - 3A16"
No, there is not special driver for the controller.
Please install the ACPI driver for ATK 0110 virtual device for a try. http://dlsvr.asus.com/pub/ASUS/misc/...PI_1043400.rar
If the problem still exists, please install a fresh WinXP OS and support CD drivers.
Lame. New V2 BIOS still didn't fix G15 (USB Keyboard) not recognized until the system boots into Windows. GRRR......
Asus P6T-DLX V2 1104 & i7 920 @ 4116 1.32v(Windows Reported) 1.3375v (BIOS Set) 196x20(1) HT OFF
6GB OCZ Platinum DDR3 1600 3x2GB@ 7-7-7-24, 1.66v, 1568Mhz
Sapphire 5870 @ 985/1245 1.2v
X-Fi "Fatal1ty" & Klipsch ProMedia Ultra 5.1 Speaks/Beyerdynamic DT-880 Pro (2005 Model) and a mini3 amp
WD 150GB Raptor (Games) & 2x WD 640GB (System)
PC Power & Cooling 750w
Homebrew watercooling on CPU and GPU
and the best monitor ever made + a Samsung 226CW + Dell P2210 for eyefinity
Windows 7 Utimate x64
Do you have all USB stuff enabled in BIOS?
i7 2600K | Asus Maximus IV Extreme | 8GB DDR3 1600 C9 Corsair Vengeance | GTX580 Matrix Platinum | Vertex 2 120GB | Auzen X-Fi HomeTheater HD | Corsair AX1200 | FT02
EK Supreme HF Full Nickel | MCR320 XP + GT AP15| DDC3.25 + EK Top V2| EK Multioption Res X2 150 Advance | Bitspower Fittings & Rotaries
My flickr
Reply With Quote
Bookmarks