** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[oMek]

I've had this board for about a month now, my cpu overclock is stable 4000hmz@8x500 but im really lost on the memory settings.

here is how its set now.. (dont pay attention too the volts I was messing around trying something out :P)

Im looking too either get my ram too 1200mhz, or keep it at 1000mhz with better timein, whatever will give me better memory bandwith

i have the G.Skill PI8800 (1100mhz 5-5-5-15 1.8-1.9v)

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 3.8GHz............................[ 500 x 8.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 700mv   ]
PCI Express Clock Drive.........................[ 700mv   ]
CPU Clock Skew..................................[ 200ps     ]
MCH Clock Skew..................................[ 200ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Turbo ]
Extreme Memory Profile............................[ Profile1 ]
(G) MCH Frequency Latch.........................[ 400      ]
System Memory Multipler.........................[ 2.00D    ]
Memory Frequency 1066...........................[ 1000     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ Auto    ]
tWTR[4].........................................[ Auto    ]
tWR[13]..........................................[ Auto    ]
tRFC[68]........................................[ Auto    ]
tRTP[4].........................................[ Auto    ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 10 ] ................[ Auto     ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ Auto    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 10 ] ................[ Auto     ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ Auto    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.23750 ]......................[ 1.40000 ] (gives 1.36)
CPU Termination   [ 1.20    ]...................[ 1.440   ]
CPU PLL           [ 1.50    ]...................[ 1.710   ]
CPU Reference     [ 0.760   ]...................[ Auto   ]
 
MCH Core          [ 1.100   ]...................[ 1.400   ]
MCH Reference     [ 0.760   ]...................[ Auto   ]
MCH/DRAM Refernce [ 0.900   ]...................[ Auto   ]
ICH I/O           [ 1.500   ]...................[ Auto   ]
ICH Core          [ 1.100   ]...................[ 1.200   ]
 
DRAM Voltage      [ 1.800   ]...................[ 1.900   ]
DRAM Termination  [ 0.900   ]...................[ Auto   ]
Channel A Ref     [ 0.900   ]...................[ Auto   ]
Channel B Ref     [ 0.900   ]...................[ Auto   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

[oMek]

I've had this board for about a month now, my cpu overclock is stable 4000hmz@8x500 but im really lost on the memory settings.

here is how its set now.. (dont pay attention too the volts I was messing around trying something out :P)

Im looking too either get my ram too 1200mhz, or keep it at 1000mhz with better timein, whatever will give me better memory bandwith

i have the G.Skill PI8800 (1100mhz 5-5-5-15 1.8-1.9v)

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 3.8GHz............................[ 500 x 8.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 700mv   ]
PCI Express Clock Drive.........................[ 700mv   ]
CPU Clock Skew..................................[ 200ps     ]
MCH Clock Skew..................................[ 200ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Turbo ]
Extreme Memory Profile............................[ Profile1 ]
(G) MCH Frequency Latch.........................[ 400      ]
System Memory Multipler.........................[ 2.00D    ]
Memory Frequency 1066...........................[ 1000     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ Auto    ]
tWTR[4].........................................[ Auto    ]
tWR[13]..........................................[ Auto    ]
tRFC[68]........................................[ Auto    ]
tRTP[4].........................................[ Auto    ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 10 ] ................[ Auto     ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ Auto    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 10 ] ................[ Auto     ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ Auto    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.23750 ]......................[ 1.40000 ] (gives 1.36)
CPU Termination   [ 1.20    ]...................[ 1.440   ]
CPU PLL           [ 1.50    ]...................[ 1.710   ]
CPU Reference     [ 0.760   ]...................[ Auto   ]
 
MCH Core          [ 1.100   ]...................[ 1.400   ]
MCH Reference     [ 0.760   ]...................[ Auto   ]
MCH/DRAM Refernce [ 0.900   ]...................[ Auto   ]
ICH I/O           [ 1.500   ]...................[ Auto   ]
ICH Core          [ 1.100   ]...................[ 1.200   ]
 
DRAM Voltage      [ 1.800   ]...................[ 1.900   ]
DRAM Termination  [ 0.900   ]...................[ Auto   ]
Channel A Ref     [ 0.900   ]...................[ Auto   ]
Channel B Ref     [ 0.900   ]...................[ Auto   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

anyone help me with my memory settings/overclock?

[PortCitySlim]

anyone help me with my memory settings/overclock?

DUDE! 1.71PLL is not a good idea! Your going to be way way way better off with 8.5x471 running the 2.4B strap and much much less VTT/MCH. Try these and see if you can boot. If not raise your VTT/MCh to 1.32/1.32, raise the VTT first and let the references adjust. You should be running something like ~65% of the VTT for a reference and ~67% of the MCH for a reference. You can run 2.0V ram at first and then lower it later. Get rid of that 700mv/700mv and 200ps clock skews. Try 900/900/0/0 or 1000/1000/0/50. You can also try up to 1.57PLL but NO MORE. Boot with these setting first though. Good luck

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 3.8GHz............................[ 471 x 8.5]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 471      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 900mv   ]
PCI Express Clock Drive.........................[ 900mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 0ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.40B    ]
Memory Frequency 1066...........................[ 1130     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ Auto       ]
tWTR[4].........................................[ Auto       ]
tWR[13]..........................................[ Auto       ]
tRFC[68]........................................[ 55      ]
tRTP[4].........................................[ Auto       ]
Command Rate (cmd)[0]...........................[ 2T      ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15 ]......................[ 1.4000 ]
CPU Termination   [ 1.20    ]...................[ 1.280   ]
CPU PLL           [ 1.50    ]...................[ 1.500   ]
CPU Reference     [ 0.760   ]...................[ 0.835   ]
 
MCH Core          [ 1.100   ]...................[ 1.300   ]
MCH Reference     [ 0.760   ]...................[ 0.850   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 1.000   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 2.000   ]
DRAM Termination  [ 0.900   ]...................[ 1.000   ]
Channel A Ref     [ 0.900   ]...................[ 1.000   ]
Channel B Ref     [ 0.900   ]...................[ 1.000   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

[oMek]

DUDE! 1.71PLL is not a good idea! Your going to be way way way better off with 8.5x471 running the 2.4B strap and much much less VTT/MCH. Try these and see if you can boot. If not raise your VTT/MCh to 1.32/1.32, raise the VTT first and let the references adjust. You should be running something like ~65% of the VTT for a reference and ~67% of the MCH for a reference. You can run 2.0V ram at first and then lower it later. Get rid of that 700mv/700mv and 200ps clock skews. Try 900/900/0/0 or 1000/1000/0/50. You can also try up to 1.57PLL but NO MORE. Boot with these setting first though. Good luck

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 3.8GHz............................[ 471 x 8.5]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 471      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 900mv   ]
PCI Express Clock Drive.........................[ 900mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 0ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.40B    ]
Memory Frequency 1066...........................[ 1130     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ Auto       ]
tWTR[4].........................................[ Auto       ]
tWR[13]..........................................[ Auto       ]
tRFC[68]........................................[ 55      ]
tRTP[4].........................................[ Auto       ]
Command Rate (cmd)[0]...........................[ 2T      ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15 ]......................[ 1.4000 ]
CPU Termination   [ 1.20    ]...................[ 1.280   ]
CPU PLL           [ 1.50    ]...................[ 1.500   ]
CPU Reference     [ 0.760   ]...................[ 0.835   ]
 
MCH Core          [ 1.100   ]...................[ 1.300   ]
MCH Reference     [ 0.760   ]...................[ 0.850   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 1.000   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 2.000   ]
DRAM Termination  [ 0.900   ]...................[ 1.000   ]
Channel A Ref     [ 0.900   ]...................[ 1.000   ]
Channel B Ref     [ 0.900   ]...................[ 1.000   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

well i tryed your settings, so far so good! i feel much more safe with the lower volts. i lost some memory bandwith via everest but that could be due too my raid volume rebuilding atm.

going too stress it some and see if its stable now =) thanks!

[PortCitySlim]

well i tryed your settings, so far so good! i feel much more safe with the lower volts. i lost some memory bandwith via everest but that could be due too my raid volume rebuilding atm.

going too stress it some and see if its stable now =) thanks!

Great! Just remember that using the 2.4B strap might prevent you from running 1.34VTT/1.34MCH(I do not think you will need it that high) so don't freak out if you can not boot or instant BSOD if you try that high. I think you might be able to go lower on the ram then I suggested but make 100% sure your vcore/vtt/mch levels are stable before lowering your ram. If you get BSOD's or prime fails do not change to many settings at one time. Those settings are pretty much identical to what I can run my 9650 at with 9x471, since you have a 9550 then 8.5x471 should be spot on.