DFI LP UT X58-T3EH8 - First bench, bios screens etc

[sjakie666]

as i stated earlier.. i have problems with a fan still spinning after i shut down my computer. i tried a other psu tonight and the issue is still there.. i even tried other electric points in my house! i'm lost.. anyone got more idea's???

thnx in advance

[Sam_oslo]

I tried with 2176-2560 and nothing. Sometimes even with stock settings i can´t load windows. I need to enter bios, save and exit(don´t need to change nothing), and works perfect.
This board is killing my patience

Have you tried asking Zotac or Nvidia for help or posted on the DFI Club Forum yet? There has to be hundreds of folks out of there with a x58 board and a 295.

GTX 295 can't be the problem, it has been working fine with several different BIOS (including the first "out of box" BIOS, and the last beta) on my DFI UT X58.

[Dami3n]

GTX 295 can't be the problem, it has been working fine with several different BIOS (including the first "out of box" BIOS, and the last beta) on my DFI UT X58.

Please, could you post your bios settings?

[sjakie666]

lol maybe we can change boards.... i don't wanna change if it's rev 56/58 :S

[cstkl1]

lol maybe we can change boards.... i don't wanna change if it's rev 56/58 :S

that my friend is a problem unless ure in malaysia..
or singapore.

no idea on the revision other than it came with the feb 6 bios

[Sam_oslo]

Please, could you post your bios settings?

GTX 295 has been working fine with several different BIOS-settings that i have tried and never had such a issues that you have. I had to save the BIOS (again) a few times, but it has always been due to hardware-changes (one time, even after installing a new fan ), but never related to GTX 295. I use this settings for 4.01GHZ (211x19) for 24/7:

Genie BIOS Setting

CPU Feature
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Memory Control Setting: AUTO
Memory LowGap: 2048M

DRAM Command Rate: AUTO
CAS Latency Time (tCL): 6
RAS# to CAS# Delay (tRCD): 6
RAS# Precharge (tRP): 6
Precharge Delay (tRAS): 30
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): AUTO
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1.37500v 
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.650v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: AUTO
CPU VTT Voltage: 1.34v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation

CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.13v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 19x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: x36
CPU Base Clock (BCLK): 211 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 100 Mhz
DRAM Frequency: x6
UnCore Frequency: x16

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

[Dami3n]

Nothing. I tried 2048, 2176, 2560, and even 3072.
Cold boot(i always switch off psu in the night) with stock settings->code 94. I need to enter bios, save and exit, and all works.
Boot with oc settings->code 94. No matter what i do, after the first boot screen pc stops with f.....g code and black screen. I tried different settings, even 200x16, without success. Is annoying

I think my board won a travel to rma.

[eva2000]

Nothing. I tried 2048, 2176, 2560, and even 3072.
Cold boot(i always switch off psu in the night) with stock settings->code 94. I need to enter bios, save and exit, and all works.
Boot with oc settings->code 94. No matter what i do, after the first boot screen pc stops with f.....g code and black screen. I tried different settings, even 200x16, without success. Is annoying

I think my board won a travel to rma.

try musical chairs with memory modules alternating in dimm 2+4+6 slots. label each module with masking tape 1, 2, 3 and try all combinations so

1, 2, 3
1, 3, 2
2, 3, 1
2, 1, 3
3, 1, 2
3, 2, 1

[Dami3n]

try musical chairs with memory modules alternating in dimm 2+4+6 slots. label each module with masking tape 1, 2, 3 and try all combinations so

1, 2, 3
1, 3, 2
2, 3, 1
2, 1, 3
3, 1, 2
3, 2, 1

Nothing

[cstkl1]

as i stated earlier.. i have problems with a fan still spinning after i shut down my computer. i tried a other psu tonight and the issue is still there.. i even tried other electric points in my house! i'm lost.. anyone got more idea's???

thnx in advance

hmm dunno why u find that a problem
i wished my board did that.