** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[Bail_w]

The vdrop is kinda bad, under load CPU-Z only reports 1.248v and thats with LLC enabled. With the 2nd template I had posted, that results in CPU-Z reading 1.312v under load. So that's a .06v increase going from 4100 to 4250.

still, you expect to gain 150ghz with .06v increase in voltages which quite impossible. Perhaps, you should try 4200.

[Jor3lBR]

Did you ever get your mounting for your cryo.....

I was hoping to see you beat your own records...

always great info

Hey Viper thanks!

Yes I did get the CryoZ mount and did fit it already all I need know is some spare time

I was setting up a 4500MhzQ9650+UD3P system for a friend this week. I told him I'll eat my cpu if I didn't get his Quad stable at those speed so he could ditch the Asus MF2.

[mattlyall06]

Hey Viper thanks!

Yes I did get the CryoZ mount and did fit it already all I need know is some spare time

I was setting up a 4500MhzQ9650+UD3P system for a friend this week. I told him I'll eat my cpu if I didn't get his Quad stable at those speed so he could ditch the Asus MF2.

lucky friend!

[phsinc1]

does the EP45-UD3R overclocks same like the EP45-UD3P .... I can't find the UD3P in my country, only the UD3R available.

[mreld3r]

does the EP45-UD3R overclocks same like the EP45-UD3P .... I can't find the UD3P in my country, only the UD3R available.

here take a look at this:
http://valid.canardpc.com/show_oc.php?id=507623
This is done by stasio, ddr2 1800

[529th]

Are the UD3P boards better overclockers than the UD3R?

[stasio]

here take a look at this:
http://valid.canardpc.com/show_oc.php?id=507623
This is done by stasio, ddr2 1800

I only posted WR and GIGABYTE Challenge Dual Channel DDR2-1508 Record winner by Shahryar

[hicookie]

Are the UD3P boards better overclockers than the UD3R?

UD3P & UD3R performance is the same, but if you have Daul ati graphics
then UD3P could run crossfirex, also P version has Ultra-TMP function

[systemviper]

Hey Viper thanks!

Yes I did get the CryoZ mount and did fit it already all I need know is some spare time

I was setting up a 4500MhzQ9650+UD3P system for a friend this week. I told him I'll eat my cpu if I didn't get his Quad stable at those speed so he could ditch the Asus MF2.

I'm getting a phase in about a week or two, So i'll be reaching for the starzzz.. look forward to seeing your there

[InterMurph2]

I am new to the UDP3 board, after 2.5 years with an Asus P5W DH Deluxe.

I quickly got my Q9650 up to 4.0 GHz (445 * 9). It ran Prime blend for 20 hours with no problems.

Any attempts to go beyond that result in BSODs at the worst, Prime95 errors at the best.

Can anybody suggest what I should change first? This is air cooled.

Thanks.

PS My memory is Patriot PC2-6400/800MHz rated at 4-4-4-12; I have the timings manually set to 5-5-5-15 for 890MHz.

[Jor3lBR]

I am new to the UDP3 board, after 2.5 years with an Asus P5W DH Deluxe.

I quickly got my Q9650 up to 4.0 GHz (445 * 9). Any attempts to go beyond that result in BSODs at the worst, Prime95 errors at the best.

Can anybody suggest what I should change first? This is air cooled.

Thanks.

CPU Ref is too highfor starters, skew must be 1000/1000/0/50 and Dram Term and Refs are all off too just use AUTO for DRAM Terms and Ref for starters and lower your CPU Ref.

[DOM.]

has any one gotten high fsb stable ? i cant seem to get it with my E8500 i tryed that 64-67% doesnt help at all

cuz on auto i gotten 600fsb to post but not to stable

like to run 550fsb

its a nice mobo but to much stuff to mess with

[marcnapier]

has any one gotten high fsb stable ? i cant seem to get it with my E8500 i tryed that 64-67% doesnt help at all

cuz on auto i gotten 600fsb to post but not to stable

like to run 550fsb

its a nice mobo but to much stuff to mess with

Hi, you asked me what revision my board is, it's 1.1.

Do you have any ideas for me since we're running same cpu? My other posts have stuff I've tried.

And I totally agree, way too much stuff to adjust on this board. I would like to get either 442x9.5 or 467x9.

Best I can do prime stable is 450x9 ram at 1080.

Any help would be appreciated,

Thanks

marc

[DOM.]

Hi, you asked me what revision my board is, it's 1.1.

Do you have any ideas for me since we're running same cpu? My other posts have stuff I've tried.

And I totally agree, way too much stuff to adjust on this board. I would like to get either 442x9.5 or 467x9.

Best I can do prime stable is 450x9 ram at 1080.

Any help would be appreciated,

Thanks

marc

yeah it been a pain for me also i got the X3350 WR but i just gave it volts lol

but is yours a E0 ? im priming mine right now at 442X9.5 with all settings at normal just set the vcore and mem volts

[radaja]

what are you guys talking about?this board bios settings are pretty basic.in fact it has less than most.

[DOM.]

well from a Asus P5B Dlx to this to much bs cuz i could get 550-580 easy with my E8500 now its like pulling teeth

cuz why does it need reference volts

whats the best bios on this mobo ?

[radaja]

for me F4 and F5.i hear you on ref volts.MIIF had 4 cpu settings and my new ut-p35 has two but at least with this board you have one for the cpu and one for the mchnce you find the sweet spot this board is a monster.it really can fly.you just have to experiment with them

[DOM.]

@marcnapier

its still going at 442X9.5 with all set to normal just CPU Vcore and DRAM Voltage i set and mem @ 1061Mhz

[coop]

Gettintg ready to make some pi

[marcnapier]

yeah it been a pain for me also i got the X3350 WR but i just gave it volts lol

but is yours a E0 ? im priming mine right now at 442X9.5 with all settings at normal just set the vcore and mem volts

Yes mine is E0. X3350 WR?? Sorry Don't know what that is, water cooling?

Yeah I tried it a bunch of different ways and it will bootm but won't run prime for more than 5 mins before errors.

@marcnapier

its still going at 442X9.5 with all set to normal just CPU Vcore and DRAM Voltage i set and mem @ 1061Mhz

What volts are you using? I tried 1.4 vcore but the vdroop drops it to 1.36 or there aboutsm tried 1.42 and vdroop is better, but prime crashes faster.

What mem volts? Are you running 333 or 400 at 1061 and 2.0b or......??

Thanks for any info

marc

[technut36]

Hey guys i am making a budget PC for a buddy. Before i went i7 i worked with 3 ud3p and i freaking loved em.

so for my friend i am thinking about UD3L / E7400. What is a decent oc i could attain with that. Also whats a good cheap 4gb kit that u guys would recommend for oc on ud3L with 7400.

thanks buds.

[marcnapier]

well from a Asus P5B Dlx to this to much bs cuz i could get 550-580 easy with my E8500 now its like pulling teeth

cuz why does it need reference volts

whats the best bios on this mobo ?

I agree, on my P5Q Dlx board all I did was change vcore, turn off all the usual speedstep, c1e etc. and and unlatch ram....and something else can't remember...probably ram volts, and wham 4.2Ghz prime stable....totally stable.

marc

[MADMAX22]

well from a Asus P5B Dlx to this to much bs cuz i could get 550-580 easy with my E8500 now its like pulling teeth

cuz why does it need reference volts

whats the best bios on this mobo ?

You must of had a golden p5b deluxe I would think,

If you think this has alot of options stay away from a dfi board.

Anyways I took my E3110 to 600fsb bottable, and 630 would run memtest for a while. All I did was change the vcore, vmch, vddr and turn off c1e and such. The other voltages you can play with to make it stable.
http://valid.canardpc.com/show_oc.php?id=516599

Personally I really like this board so far. Very easy to oc and has enough options to tweak it to pull those extra mhz.

[xbiusx]

Gettintg ready to make some pi

I`m still surprise every time u post your new settings

I`m fighting with my system to get stable at 4.2 (8.5x495) but fails small ftt after 30 min and blend test in few minutes.

Now i`m running 2x2gb Mushkin 996599 but i don`t understand how the whole thing becomes unstable just with increase 5 notches in FSB, and how hard it is to make it stable again...

LLC enabled
vcore 1.39
vtt 1.30
pll 1.61
ref 0.815

vnb 1.42
vdimm 2.24
ref 0.68

5-5-5-15 pl9

rest normal...

any suggestioin?

[ChuckM]

Hey guys i am making a budget PC for a buddy. Before i went i7 i worked with 3 ud3p and i freaking loved em.

so for my friend i am thinking about UD3L / E7400. What is a decent oc i could attain with that. Also whats a good cheap 4gb kit that u guys would recommend for oc on ud3L with 7400.

thanks buds.

I've got mine to 3.8GHz, vcore @1.4 to do it. I'm gonna try to hit 4.0 just to see if I can, but I'm gonna run 3.6 for my 24/7 setting. My combination does it easy.