Hi friends.

I have a problem with the FSB of my Mother Board

this is my setup at the moment and I can not climb over the FSB.

GIGABYTE GA-EP45-UD3P
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: [Auto]
CPU Clock Ratio .........................: 9
Fine CPU Clock Ratio.....................: [+0.0]
CPU Frequency ...........................: 4.68GHz

Clock Chip Control

Standard Clock Control
CPU Host Clock Control..................: [Enabled] [Disabled]
CPU Host Frequency (Mhz) ............: 520Mhz
PCI Express Frequency (Mhz) .........: [Auto]
C.I.A. 2.............................: [Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive...................: 700mv
CPU Clock Skew (ps).......................: 0ps
MCH Clock Skew (ps).......................: 0ps

DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [Auto]
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ................: 1040
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time...............................: 5
tRCD ..........................................: 5
tRP'...........................................: 5
tRAS...........................................: 15

Advanced Timing Control [Press Enter]
tRRD...........................................: 5
tWTR...........................................: 5
tWR............................................: 8
tRFC...........................................: 52
tRTP...........................................: 5
Command Rate (CMD) ............................: 2

Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value......................: [Auto]
tRD Phase0 Adjustmen...................: [Auto]
tRD Phase1 Adjustment...................: [Auto]
tRD Phase2 Adjustment .................: [Auto]
tRD Phase3 Adjustment..................: [Auto]
Trd2rd(Different Rank)..................: [Auto]
Twr2wr(Different Rank)..................: [Auto]
Twr2rd(Different Rank)..................: [Auto]
Trd2wr(Same/Diff Rank)..................: [Auto]
Dimm1 Clock Skew Control................: [Auto]
Dimm2 Clock Skew Control................: [Auto]
DDR Write Training......................: [Disabled}

Channel A Driving Settings [Press Enter]
Driving Strength Profile:..............: [AUTO]
Data Driving Pull-Up Level.............: [Auto]
Cmd Driving Pull-Up Level..............: [Auto]
Ctrl Driving Pull-Up Level.............: [Auto]
Clk Driving Pull-Up Level..............: [Auto]

Data Driving Pull-Down Level...........: [Auto]
Cmd Driving Pull-Down Level............: [Auto]
Ctrl Driving Pull-Down Level...........: [Auto]
Clk Driving Pull-Down Level............: [Auto]

Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value......................: [Auto]
tRD Phase0 Adjustmen...................: [Auto]
tRD Phase1 Adjustment...................: [Auto]
tRD Phase2 Adjustment .................: [Auto]
tRD Phase3 Adjustment..................: [Auto]
Trd2rd(Different Rank)..................: [Auto]
Twr2wr(Different Rank)..................: [Auto]
Twr2rd(Different Rank)..................: [Auto]
Trd2wr(Same/Diff Rank)..................: [Auto]
Dimm1 Clock Skew Control................: [Auto] ps
Dimm2 Clock Skew Control................: [Auto] ps
DDR Write Training......................: [Disabled}

Channel B Driving Settings [Press Enter]
Driving Strength Profile:..............: [AUTO]
Data Driving Pull-Up Level.............: [Auto]
Cmd Driving Pull-Up Level..............: [Auto]
Ctrl Driving Pull-Up Level.............: [Auto]
Clk Driving Pull-Up Level..............: [Auto]

Data Driving Pull-Down Level...........: [Auto]
Cmd Driving Pull-Down Level............: [Auto]
Ctrl Driving Pull-Down Level...........: [Auto]
Clk Driving Pull-Down Level............: [Auto]


Motherboard Voltage Control
Voltage Type.…...……... Normal
CPU
Load-Line Calibration....................: [Enabled]
CPU Vcore….……….........1.22500V*.........: 1.4500
CPU Termination…...... 1.200V*...........: [Auto]
CPU PLL………………….........1.500V*...........:[Auto]
CPU Reference..........0.760V............: [Auto]
MCH/ICH
MCH Core……………..........1.100V............: 1.400
MCH Reference..…...….….0.760V............: [Auto]
MCH/DRAM Reference.....0.900V............: [Auto]
ICH I/O…………....……......1.550V............: [Auto]
ICH Core...............1.100V............: [Auto]
DRAM
DRAM Voltage ……........1.800V............: 2.32
DRAM Termination ...…..0.900V............: [Auto]
Channel A Address Vref 0.900V............: [Auto]
Channel B Address Vref 0.900V............: [Auto]

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect.................: [Disabled]
CPU Enhanced Halt (C1E)...................: [Disabled]
C2/C2E State Support......................: [Disabled]
x C4/C4E State Support....................: [Disabled]
CPU Thermal Monitor 2(TM2) ...............: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology.................: [Disabled]
Note: * refers to 45nm CPU
any suggestions?