New Memory Tweaker for Intel Chipsets

[FELIX]

=> msgclb & ol'norton: could you check memory frequency with this version: memset40beta4


=> mikeyakame: probably it's the same method ("Note both IOh and non-core have this now" in the doc)
but at what address? I think elsewhere that Dev:0 Fct:1 OffSet:4C...

[msgclb]

=> msgclb & ol'norton: could you check memory frequency with this version: memset40beta1[/URL]

I still have the same problem although CPU-Tweaker 1.0 beta4 is correct.

[mikeyakame]

felix,

seems like, bus:0?, device:0, function:1, dId:2C01h, os: 4Ch

Table 17-1. Functions Specially Handled by the IOH
Register Group: DMI (Device 0 in DMI mode)
DID: 0011_0100_00 00_0xxxb
Device:0 Function:0
Comment: The DMI port will have the last 3 bits of the DID (xxx) IOH = 000

Excerpt from X58 express chipset datasheet.

My understanding is from this that unless you explicitly address a DMI DID for Dev0Fn0 you will be address the NonCore DID Dev0Fnx.

The information seems to suggest this anyhow. Intel Datasheet's are like cryptic puzzles!
The address decoding/encoding seems very complex on the m-arch, and will probably take some time to fully understand.

[stasio]

CPU-Tweaker v:1.0 beta5

[FELIX]

=> msgclb & ol'norton: frequency reading will probably work in this version: memset40beta2
Sorry guys.

[s3rv3r]

Both I couldn`t apply my changes.

[stasio]

Frequency reading(578.7-CPU-Z):
beta1= 0
beta2= 577-580.6 ,every 2 seconds
MemSet 3.6= 578.7

[msgclb]

=> msgclb & ol'norton: frequency reading will probably work in this version: memset40beta2
Sorry guys.

Nothing to be sorry for. Now let me see what else I can find!

[ol'norton]

Memset 4.0 Beta 2 now reads frequency & timings as set in bios.
CPU Tweaker 1.0 Beta 2 is out on tRFC , tRRD , & Round Trip latency.

[FELIX]

memset40beta3

-Improve frequency reading.
-Improved reading SPD info on DDR2 & DDR3.

[eva2000]

memset40beta3

-Improve frequency reading.
-Improved reading SPD info on DDR2 & DDR3.

Seems 16x mem multi on DFI UT X58-T3EH8 not reporting right frequency - 14x mem has no probs

Seems with 16x memory multiplier, both Memset 4.0 Beta2 and CPU Tweaker tool can't report the right memory clock frequency. Had no problems with 14x memory multiplier.

Vcore = 1.05v
DRAM Voltage = 1.965v
CPU VTT = 1.48v + 0.075v









CPUZ dump here

[FELIX]

I add 16x and 18x multi in this version: memset40beta4

and in this CPU-Tweaker version: CPU-Tweaker 1.0 beta6

also some bugs fixed on both software...

[eva2000]

woohoo thanks will test

[hiwa]

[eva2000]

I add 16x and 18x multi in this version: memset40beta4

and in this CPU-Tweaker version: CPU-Tweaker 1.0 beta6

also some bugs fixed on both software...

Hi Felix, any chance of adding a motherboard brand/model to cpu tweaker app ? would be one less cpuz instance I'd need to load for screenshot capturing

[kuebk]

Guys I have odd problem using Memset 3.6/4.0 beta 4. I can't change anything the only button that works are About and Exit, here is how does it look like:



I'm using Abit IP35-PRO and WinXP x64.

ISO: Help, thanks.

[eva2000]

I add 16x and 18x multi in this version: memset40beta4

and in this CPU-Tweaker version: CPU-Tweaker 1.0 beta6

also some bugs fixed on both software...

weird one i put in 3x1GB Gskill PC3-12800HZ Micron D9JNM on DFI UT X58-T3EH8 and with CPU tweaker 1.0 beta 6 when loading it says you must have a module installed in channel A and then closes itself. But load Memset 4.0 beta 4 and it's fine ???

[BenchZowner]

Guys I have odd problem using Memset 3.6/4.0 beta 4. I can't change anything the only button that works are About and Exit, here is how does it look like:



I'm using Abit IP35-PRO and WinXP x64.

ISO: Help, thanks.

Any BIOS version starting from v12 & up locks the MCHBar and you cannot use MemSet.
Don't know if they fixed it in a newer release, I've tested various BIOSes up to v16 before I sold the board and the lock was still there.

[FELIX]

Hi Felix, any chance of adding a motherboard brand/model to cpu tweaker app ? would be one less cpuz instance I'd need to load for screenshot capturing

...maybe soon, I don't know yet.

weird one i put in 3x1GB Gskill PC3-12800HZ Micron D9JNM on DFI UT X58-T3EH8 and with CPU tweaker 1.0 beta 6 when loading it says you must have a module installed in channel A and then closes itself. But load Memset 4.0 beta 4 and it's fine ???

...could you send me a cpuz register dump at memset@hotmail.fr,
thank.

[eva2000]

...maybe soon, I don't know yet.


...could you send me a cpuz register dump at memset@hotmail.fr,
thank.

I rearranged my 3x1GB Gskill PC3-12800HZ Micron D9JNM in same dimm slot and now no more message and can load cpu tweaker 1.06 beta 6! weird.. didn't take a dump in cpuz but will when i come across the message again

[BulldogPO]

Any info when it will be posible change settings on X58 boards?

[FELIX]

Any info when it will be posible change settings on X58 boards?

...no idea; Maybe someone will find the solution.

[FELIX]

MemSet 4.0 finale version: MemSet40.zip

-Use WinRing0 driver.
-Running under Windows 7 has been improved.
-Interface is the same for all chipsets/CPUs.
-Add support for Intel Core i7 CPU (Reading only).
-Loading time was improved.
-Improve frequency reading on Core i7.
-Improved reading SPD info on DDR2 & DDR3.
-Fixe frequency reading on some Core 2 Duo CPU.


CPU-Tweaker 1.0 beta6

-Running under Windows 7 has been improved.
-Fix a bug with spd detection.

[FELIX]

Hi Felix, any chance of adding a motherboard brand/model to cpu tweaker app ? would be one less cpuz instance I'd need to load for screenshot capturing

...be happy eva2000: CPU-Tweaker 1.0 beta7

[eva2000]

WOOHOO... thanks Felix

one less cpuz instance to load!