I think I was stable at 450 fsb but I am not.After 1.5 hours during prime95 blend stressing my computer did not BSOD.here is my 450 fsb settings ;
Code:
>CPU Feature:
Thermal Management Control.......... - Enabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Disabled
Virtualization Technology........... - Disabled
Core Multi-Processing............... - Enabled
>DRAM Timing:
Enhance Data transmitting........... - Fast
Enhance Addressing.................. - Fast
T2 Dispatch......................... - Auto
>Clock Setting Fine Delay Press Enter:
DLL And RCOMP Settings.............. - Auto
Ch1 Dram Defaul Skew................ - Model 0
Ch2 Dram Defaul Skew................ - Model 0
RCOMP Settings...................... - Model 2
Fine Delay Step Degree.............. - 70ps
Ch1 Clock Crossing Setting.......... - Auto
DIMM1 Clock Fine Delay.............. - Current[1346ps]
DIMM2 Clock Fine Delay.............. - Current[1346ps]
Ch1 Control0 Fine Delay............. - Current[166ps]
Ch1 Control1 Fine Delay............. - Current[166ps]
Ch1 Control2 Fine Delay............. - Current[124ps]
Ch1 Control3 Fine Delay............. - Current[110ps]
Ch1 Command Fine Delay.............. - Current[262ps]
Ch2 Clock Crossing Setting.......... - Auto
DIMM3 Clock Fine Delay.............. - Current[1346s]
DIMM4 Clock Fine Delay.............. - Current[1346ps]
Ch2 Control0 Fine Delay............. - Current[14ps]
Ch2 Control1 Fine Delay............. - Current[56ps]
Ch2 Control2 Fine Delay............. - Current[0ps]
Ch2 Control3 Fine Delay............. - Current[0ps]
Ch2 Command Fine Delay.............. - Current[110ps]
Ch1 Ch2 Common Clock Setting........ - Auto
Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto
Flex Memory Mode..................... - Auto
CAS Latency Time (tCL)............... - Auto
RAS# to CAS# Delay (tRCD)............ - Auto
RAS# Precharge (tRP)................. - Auto
Precharge Delay (tRAS)............... - Auto
All Precharge to Act................. - Auto
REF to ACT Delay (tRFC).............. - Auto
Performance Level.................... - Auto
>Read delay phase adjust Press Enter:
Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto
Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto
Write to PRE Delay (tWR)............ - Auto
Rank Write to Read (tWTR)........... - Auto
ACT to ACT Delay (tRRD)............. -Auto
Read to Write Delay (tRDWR)......... - Auto
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - Auto
ALL PRE to Refresh.................. - Auto
>Voltage Settings:
CPU VID Control..................... - 1.40V
CPU VID Special Add................. - Enabled
CPU VID Special Add................. - Auto
DRAM Voltage Control................ - 2.21v
SB Core/CPU PLL Voltage............. - 1.55v
NB Core Voltage..................... - 1.351v
CPU VTT Voltage..................... - 1.27v1
Vcore Droop Control................. - Enabled
Clockgen Voltage Control............ - 3.60v
GTL+ Buffer Strength................ - Strong
CPU GTL 0 REF Volt.................. - 0.6400
CPU GTL 2 REF Volt.................. - 0.6400
CPU GTL 1 REF Volt.................. - 0.6400
CPU GTL 3 REF Volt.................. - 0.6400
North Bridge GTL 0 REF Volt......... - 0.6250
North Bridge GTL 1 REF Volt......... - 0.6250
FSB Vref............................ - Auto
Genie BIOS Settings:
Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
AC Shutdown Free.................... - Enabled
O.C Clock Fail Retry Counter........ - 1
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 8.5
Target CPU Clock.................... - 3825 MHz
CPU Clock........................... - 450
Boot Up Clock....................... - 350
CPU Clock Amplitude................. - 800mV
CPU Clock0 Skew..................... - 200ps
CPU Clock1 Skew..................... - 200ps
DRAM Speed.......................... - 400/800
Target DRAM Speed................... - 900MHz
PCIE Clock.......................... - 100mhz
PCIE Slot Config.................... - 1x 1x
CPU Spread Spectrum................. - Disabled
PCIE Spread Spectrum................ - Disabled
I try to reach 4ghz 24/7 but I can not be stable at 450 fsb yet. What is your recommandations C-N?
Bookmarks