Phenom 9950 Overclocking

[Chicken Patty]

Your overall HT will be around 1600mhz,, yes going High CPU clocks the Phenom like Lower than 2000ht..I can be tricky so adjust one setting at a time ..Even the Ram dividers can afect how stable the HT will clock.


Ht @ 1.8 or 1.6 and even 1.4 ...it all depends on if you are raising the HTT above 200

200 x 7 = 1400mhz ht = 1.4
200 x 8 = 1600mhz ht = 1.6
200 x 9 = 1800mhz ht = 1.8
200 x10 = 2000mhz ht (stock) = 2.0

Going above 200 will also raise the givin divider for HT ,,

220 x 7 = 1540mhz ht
220 x 8 = 1760mhz ht
220 x 9 = 1980mhz ht
220 x10 = 2200mhz ht


210 x 7 = 1470mhz ht
210 x 8 = 1680mhz ht
210 x 9 = 1890mhz ht
210x10 = 2100mhz ht

Hope that helps..

gOtVolTage

gotcha, thanks dude.


One more question, when you say looser timings, how much looser from what they run at did you set yours?

[gOtVoltage]

Hmm it will depend on your ram...My says 5-5-5-12 @1200mhz @ 2.3volts

I can do 1280mhz with 6-6-6-18 or 6-7-7-24.. it gets tricky ..if anything run you r ran on auto then change it to manual and write down what it set.. then raise the settings up one notch ..

So if it reads 5-5-5-18 2t @ 800 divider ( when set to auto)
Change it to 6-6-7- 18(or 21) .. (manualy ) ..

you can always set tigher timing after you get that high OC..

wright down what you change ,,so you know what works and what dosnt

Note: use CPU-Z to check what Volts your Ram runs and what timing.. But do the Auto ram timing first and i bet CPU-Z will show its set slightly higher(looser) than what its specs are.

[*GameOver*]

Yeah my room is cool. Its winter and i leave the window open. Here ill get you some SS's





Im running 2 120mm fans on a V8 Prototype from Coolermaster. Works fairly well.



This is a pic of the PC minus the 2 fans will get a new picture once i find the ole camera

[Chicken Patty]

Hmm it will depend on your ram...My says 5-5-5-12 @1200mhz @ 2.3volts

I can do 1280mhz with 6-6-6-18 or 6-7-7-24.. it gets tricky ..if anything run you r ran on auto then change it to manual and write down what it set.. then raise the settings up one notch ..

So if it reads 5-5-5-18 2t @ 800 divider ( when set to auto)
Change it to 6-6-7- 18(or 21) .. (manualy ) ..

you can always set tigher timing after you get that high OC..

wright down what you change ,,so you know what works and what dosnt

Note: use CPU-Z to check what Volts your Ram runs and what timing.. But do the Auto ram timing first and i bet CPU-Z will show its set slightly higher(looser) than what its specs are.

Thanks dude. You are the man. I have noticed that the timings are looser when on Auto. Ill check this out tomorrow and see what I can come up with. I just got my water setup back in and temps arent to good right now as it needs to cleart he bubble and what not.

[*GameOver*]

last but no least. Here is 3.2 ghz full load. (room got a bit cooler)

http://valid.x86-secret.com/show_oc.php?id=449205

[gOtVoltage]

GAMEOVER

Theres alot left in that chip especially since you under 40c at full load.

Actually whats it do @ 1.4- 1.45volts/ I bet 3.3ghz -3.4ghz ehhh

I know i just like to crank things...thats a mighty nice chip @ 3.2ghz and stock volts.

[*GameOver*]

werkin on it


http://valid.x86-secret.com/show_oc.php?id=449217



now gota load test it. brb aprox 1 hour :P