Micron D9 GMH\GKX\JKH etc club

[zsamz_]

Elektrosadist whats that program showing your ram temp? I want one.

i use a lasergun
btw even though they dont go over 30c dont mean they wont die lol
done of my dead ram went over 30c

[fatguy1992]

how much for a lazer gun?

[zsamz_]

how much for a lazer gun?

i paid 60$ it was used new ones average 100-200$
its a nice toy lets me know whats gettin hot and its verry precise

[WaterFlex]

Nice RAM, good job Elektrosadist

[Elektrosadist]

i'm still not there where i want to be. I'm really looking forward to the GKX chips i hope i can do 1300 MHz with them.

also, does any1 know where to find the thread about Fugger DDR2 Record at ddr2 1508? Gigabyte is just offering a competition and since i got 6 GB of Microns now i thought i might enter the competition and wreck one of my kits but i want to read a little what fugger did for that specially the voltages or the performance level he used and so on yadi yadi ya ...

[Shiranui Gen-An]

I have to give my sticks 2.5V+ for DDR2-1300, I don't know how these other guys are doing it with less than 2.4V.

[klEb]

I have to give my sticks 2.5V+ for DDR2-1300, I don't know how these other guys are doing it with less than 2.4V.

nc
http://kleb.dundee-mr.de/bilder/cell...1000erC4_1.jpg

[Shiranui Gen-An]

nc
http://kleb.dundee-mr.de/bilder/cell...1000erC4_1.jpg

You just had to rub it in didn't you.

[fatguy1992]

nc
http://kleb.dundee-mr.de/bilder/cell...1000erC4_1.jpg

WOW nice

I so got to get some CellShocks

[Elektrosadist]

i bought the last kit available here in germany for 52 bucks. will arrive tomorrow. Dunno if you can still get them in the states. But i'm really excited to see how the GKX perform.

[Shiranui Gen-An]

With all the high-end kits I have, and the boards I have (I have a DFI LT P35-T2R for Pete's sake!) you'd think at least one of them could do 650MHz+ without killing them with VDIMM...

[philbrown23]

nc
http://kleb.dundee-mr.de/bilder/cell...1000erC4_1.jpg

HOLY MOINKEY CRAP!!! 1308mhz with 1.214v vdimm at PL 4!!! i hate you

[Elektrosadist]

http://valid.x86-secret.com/show_oc.php?id=447895

crappy strap for bandwidth. even tho its at tRD 6. it also boots with that but for safe keeping i boot up with tRD 8.

DDR2 1400 PF 6




DDR2 1400 PF 7


DDR2 1400 PF 8

[CryptiK]

Electrosadist, sorry but your results are bugged, as you are using the 3:5 divider on the P45 chipset. The real divider is actually 2:3, so the real ram speed is DDR2 - 1263.

[WaterFlex]

Elektrosadist
Huge Mhz, great PL but memory brandwidth is very very poor. I have 11000 Read at 600 Mhz and PL=8.

[neo mike]

Waterflex, how much fsb ? and what divider you using to get 11,000 at 1200mgz ?. Cause im pulling 475fsb, ddr2 1260, pl 7 and only pulling 10,000 everest.

[fatguy1992]

One question, does increasing PL make the RAM faster?

[fatguy1992]

I just did my own quick test, i got a 150+ MB/s increase by dropping it from 8 to 7.

[neo mike]

yes the lower the PL, the better performance you will get out of your memory.

Thats why im curious how he is getting 11,000 in everest with pl 8, he must be overclocking his cpu and fsb big time.

[zsamz_]

11k is so easy with the right setup
try doin 12k with intell n ddr2
this my 24/7 on power save on gskills n d9 gets better

[neo mike]

Very nice scores, what PL are you running on those runs ?

[CryptiK]

Elektrosadist
Huge Mhz, great PL but memory brandwidth is very very poor. I have 11000 Read at 600 Mhz and PL=8.

Got a screen of that? And what settings were you using mate?

Also his bandwidth is low for the speed because as I said, it's bugged. The 3:5 divider on P45 boards is really the 2:3 divider. It's 1263 MHz, not 1400 MHz.

[Elektrosadist]

Electrosadist, sorry but your results are bugged, as you are using the 3:5 divider on the P45 chipset. The real divider is actually 2:3, so the real ram speed is DDR2 - 1263.

Ok i didnt knew that. so im staying on another divider then.

[zsamz_]

Very nice scores, what PL are you running on those runs ?

pl8
second pic is pl9

[WaterFlex]

Waterflex, how much fsb ? and what divider you using to get 11,000 at 1200mgz ?. Cause im pulling 475fsb, ddr2 1260, pl 7 and only pulling 10,000 everest.

Got a screen of that? And what settings were you using mate?

Also his bandwidth is low for the speed because as I said, it's bugged. The 3:5 divider on P45 boards is really the 2:3 divider. It's 1263 MHz, not 1400 MHz.

I was not stable at that setup. Will remember settings and post in few hours.