True^^, try stock. I have actually tried auto with my over clock in sig just the other day and it didn't boot so..
True^^, try stock. I have actually tried auto with my over clock in sig just the other day and it didn't boot so..
Last edited by truehighroller; 10-20-2008 at 05:07 AM.
_____________________________________________
Rig = GA-P67A-UD3P Rev 1.0 - 2600K @ 5.2~GHz 1.5v~, 1.489~v Under Load - Swiftech Water Cooling - 2 X 4GB Corsair DDR3 2000Mhz @ 1868MHz~ 9,10,9,27 @ 1.65v~ - Asus 6970 @ 950MHz / 1450MHz - 3x Western Digital RE3 320Gb 16Mb Cache SataII Drives in Raid0 - Corsair HX 850w Power Supply - Antec 1200 Case - 3DMark 11 Score = P6234 - 3DVantage Score = P26237
Ok, almost everything at stock now:
AI Overclock tuner: AUTO
CPU Ratio Setting: 8.0
FSB Strap to North Bridge: AUTO
FSB Frequency: AUTO
PCI-E Frequency: AUTO
DRAM Frequency: AUTO
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO
CPU Voltage: AUTO
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: AUTO
FSB Termination Voltage: AUTO
DRAM Voltage: AUTO
NB Voltage: AUTO
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO
Advance CPU Settings
CPU Ratio Setting: 8.0
CPU VID: Disabled
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
Q9450
Asus P5Q Deluxe (Bios 1406)
2 x 2GB Corsair Dominator PC2-8500
WD 320GB Sata II
XFX 9500GT
All powered by a Corsair TX-750W PSU!
I have a Plextor PX-712SA Sata burner, not IDE, but I have the Marvel IDE disabled in bios and run Enhanced IDE in bios in the storage section. I am running off the Red Sata ports tho. No problems here. I think the Marvel IDE works with the AHCI ok, but not too swift with the IDE when its enabled. At least that is what I have read on a few posts on forums.Originally Posted by edge130
Larry
Q9650
Asus P5Q-D Bios 1406
280 GTX FC Block
2x2gb OCZ Flex II PC2 9200
Water Cooled/ Iwaki MD20/ D-Tek Fuzion
XFX 850 Watt
OWC SSD
Running P5Q Deluxe with E8400 E0 and having troubles running any higher than 4Gig.
To get to 4Gig I need 1.368 Core Voltage (CPU-Z) and I get temps around 62 and 59 using core temp.
I've followed some guides here for BIOS settings and tried most I think but I can't get the o/c higher... This is on air with Thermaltake 120 Extreme and Schyte fan.
So are these volts and temps ok for 24/7? Can I go higher with volts?
RAM isCode:AI Overclock tuner: Manual CPU Ratio Setting: 9 FSB Strap to North Bridge: Auto FSB Frequency: 445 PCI-E Frequency: 100 DRAM Frequency: DDR2-1069 DRAM CLK Skew on Channel A1: AUTO DRAM CLK Skew on Channel A2: AUTO DRAM CLK Skew on Channel B1: AUTO DRAM CLK Skew on Channel B2: AUTO DRAM Timing Control: Auto 1st Information : CAS# Latency: 5 DRAM RAS# to CAS# Delay: 5 DRAM RAS# Precharge: 5 DRAM RAS# Activate to Precharge: 15 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time: 55 Write Recovery Time: AUTO Read to Precharge Time: AUTO 2nd Information : READ to WRITE Delay (S/D): AUTO Write to Read Delay (S): AUTO WRITE to READ Delay (D): AUTO READ to READ Delay (S): AUTO READ to READ Delay (D): AUTO WRITE to WRITE Delay (S): AUTO WRITE to WRITE Delay (D): AUTO 3rd Information : WRITE to PRE Delay: AUTO READ to PRE Delay: AUTO PRE to PRE Delay: AUTO ALL PRE to ACT Delay: AUTO ALL PRE to REF Delay: AUTO DRAM Static Read Control: Disabled DRAM Read Training: Disabled MEM. OC Charger: Enabled AI Clock Twister: Auto AI Transaction Booster: Auto CPU Voltage: 1.37500 CPU GTL Voltage Reference (0/2): AUTO CPU GTL Voltage Reference (1/3): AUTO CPU PLL Voltage: 1.6 FSB Termination Voltage: AUTO DRAM Voltage: 2.1 NB Voltage: 1.30 NB GTL Reference: AUTO SBridge Voltage: 1.20 PCIE SATA Voltage: 1.50 Load Line Calibration: Enabled CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU Clock Skew : Auto NB Clock Skew : Auto CPU Margin Enhancement: Optimized Advance CPU Settings CPU Ratio Setting: 9 CPU VID: Default Don't have this option C1E Suppport: Disabled Max CPUID Value Limit: Disabled Intel® Virtualization Tech: Disabled Vanderpool Technology: Disabled (dont have this either) CPU TM Function: Enabled Execute Disable Bit: Enabled
4GB (2x2048) DDR2 PC8500 CorsairXMS2 Dominator
Motherboard is ASUS P5Q with latest bios 1406 I believe.
Any ideas are welcome.
I guess my chip is a bad overclocker
Running P5Q Deluxe with E8400 E0 and having troubles running any higher than 4Gig.
To get to 4Gig I need 1.368 Core Voltage (CPU-Z) and I get temps around 62 and 59 using core temp.
I've followed some guides here for BIOS settings and tried most I think but I can't get the o/c higher... This is on air with Thermalright 120 Extreme and Schyte fan.
So are these volts and temps ok for 24/7? Can I go higher with volts?
RAM isCode:AI Overclock tuner: Manual CPU Ratio Setting: 9 FSB Strap to North Bridge: Set this to what your memory can handle and if at a 1:1 setting memory wise then use PL 10 rather then the 8 suggested below at first by me not thinking.. You can only use 8 for the non 1:1 settings.. FSB Frequency: 445 PCI-E Frequency: 100 DRAM Frequency: DDR2-1069 DRAM CLK Skew on Channel A1: AUTO DRAM CLK Skew on Channel A2: AUTO DRAM CLK Skew on Channel B1: AUTO DRAM CLK Skew on Channel B2: AUTO DRAM Timing Control: Auto 1st Information : CAS# Latency: 5 DRAM RAS# to CAS# Delay: 5 DRAM RAS# Precharge: 5 DRAM RAS# Activate to Precharge: 15 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time: Auto Write Recovery Time: AUTO Read to Precharge Time: AUTO 2nd Information : READ to WRITE Delay (S/D): AUTO Write to Read Delay (S): AUTO WRITE to READ Delay (D): AUTO READ to READ Delay (S): AUTO READ to READ Delay (D): AUTO WRITE to WRITE Delay (S): AUTO WRITE to WRITE Delay (D): AUTO 3rd Information : WRITE to PRE Delay: AUTO READ to PRE Delay: AUTO PRE to PRE Delay: AUTO ALL PRE to ACT Delay: AUTO ALL PRE to REF Delay: AUTO DRAM Static Read Control: Disabled DRAM Read Training: Disabled MEM. OC Charger: Enabled AI Clock Twister: Moderate AI Transaction Booster: Manual PL 8 8 or 10 depending on what memory strap you use. 1:1 USE 10 anything else I think will run 8. PULLINS = Enabled CPU Voltage: 1.37500 CPU GTL Voltage Reference (0/2): .63 CPU GTL Voltage Reference (1/3): .63 CPU PLL Voltage: 1.56 FSB Termination Voltage: 1.18 If 1.18 doesn't act right bump it to 1.20 , but only go to the highest of like 1.24 if need which I doubt. DRAM Voltage: 2.1 NB Voltage: 1.30 NB GTL Reference: AUTO SBridge Voltage: 1.20 PCIE SATA Voltage: 1.60 Set this one higher just for safety reasons. Load Line Calibration: Disabled Enabled caused me issues.. CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled CPU Clock Skew : Auto NB Clock Skew : Auto CPU Margin Enhancement: Optimized Advance CPU Settings CPU Ratio Setting: 9 CPU VID: Default Don't have this option C1E Suppport: Disabled Max CPUID Value Limit: Disabled Intel® Virtualization Tech: Disabled Vanderpool Technology: Disabled (dont have this either) CPU TM Function: Enabled Execute Disable Bit: Enabled
4GB (2x2048) DDR2 PC8500 CorsairXMS2 Dominator
Motherboard is ASUS P5Q with latest bios 1406 I believe.
Any ideas are welcome.
I guess my chip is a bad overclocker
There you go that should get you going to a better place in overclocking heaven. Don't push your voltages to hard like your gtl references and what not ..
Last edited by truehighroller; 10-21-2008 at 03:40 AM.
_____________________________________________
Rig = GA-P67A-UD3P Rev 1.0 - 2600K @ 5.2~GHz 1.5v~, 1.489~v Under Load - Swiftech Water Cooling - 2 X 4GB Corsair DDR3 2000Mhz @ 1868MHz~ 9,10,9,27 @ 1.65v~ - Asus 6970 @ 950MHz / 1450MHz - 3x Western Digital RE3 320Gb 16Mb Cache SataII Drives in Raid0 - Corsair HX 850w Power Supply - Antec 1200 Case - 3DMark 11 Score = P6234 - 3DVantage Score = P26237
Melhisedek,
I'd try dropping the Multi and increasing the FSB. I can't get a whole lot stable without a low divider. Also you might want to try increasing FSB Termination voltage to around 1.19 - 1.22.
If all else fails, you prolly just got a bum chip for an E0. My C0 requires the same for 4.0 what's your VID?
Will try what you guys advised and report back. Thanks
He had alot of issues looked like.. Try changing what I suggested where I quoted you above. Actually I made a mistake as well. recheck that quote I fixed it on the memory part. If you run 1:1 you have to use PL 10. If you can pull 333 or 266 strap where it isn't 1:1 then you can do PL 8 sorry bout that one.
Last edited by truehighroller; 10-21-2008 at 03:36 AM.
_____________________________________________
Rig = GA-P67A-UD3P Rev 1.0 - 2600K @ 5.2~GHz 1.5v~, 1.489~v Under Load - Swiftech Water Cooling - 2 X 4GB Corsair DDR3 2000Mhz @ 1868MHz~ 9,10,9,27 @ 1.65v~ - Asus 6970 @ 950MHz / 1450MHz - 3x Western Digital RE3 320Gb 16Mb Cache SataII Drives in Raid0 - Corsair HX 850w Power Supply - Antec 1200 Case - 3DMark 11 Score = P6234 - 3DVantage Score = P26237
ok dude to find ure magic 4ghz...Ok been on here lurking and trying to figure this thing out. My components consist of an E8400 stepping C0, P5Q Deluxe, and 2x2 Gig of Corsair Ram. I have been really struggling with this cpu for some time now, even with my old P35 Platinum P.O.S MSI board. The cpu is crap and very unstable @ anything ove 4 Ghz. Here are my current settings that are actually stable for quite some time now. Could use a little more help with the advanced settings such as NB GTL, FSB Termination Voltage, CPU GTL etc. I have tried some of the settings recommended here but as you will notice my voltages are quite a bit higher then most. I know I can lower them a bit if I can understand what these other settings actually do. thx
JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 7.5
FSB Strap to North Bridge:333
FSB Frequency: 533
PCI-E Frequency: 100
DRAM Frequency: 1066
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 18
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 52-64 for ure 4gb kit.. or whatever works
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Disabled (cause then 533 fsb would be pointless)
AI Clock Twister: Moderate
AI Transaction Booster: Manual
Strenght 10
CPU Voltage: Will tell u how to find 4ghz vcore the easy way
CPU GTL Voltage Reference (0/2):0.63
CPU GTL Voltage Reference (1/3):0.63
CPU PLL Voltage: 1.5
FSB Termination Voltage: 1.16
DRAM Voltage: Set what ure rams if its the Corsair PC2-8500 4gb rated vdimm is
NB Voltage: 1.32
NB GTL Reference: Auto
SBridge Voltage: 1.5
PCIE SATA Voltage: 1.1
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
CPU Margin Enhancement : Optimized
Advance CPU Settings
CPU Ratio Setting: 7.5
C1E Suppport: disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Enabled
CPU TM Function: Disabled
Execute Disable Bit: Enabled
Intel SpeedStep Tech : disabled
since ure using e8400..
set everything above except
multiplier 9
bus 445
...
run linpack on vista 64 diagnostic mode max mem say around 30-50 times..
up ure vcore until u get this stable and then use back the template above with the vcore...
cheers...
well the template above with tRFC 25 works like a charm for 4x1gb kit.. so the major difference might be..
u may actually lower the vNB... and keep a high tRFC .
also a good practise after u completedthe multi 9 bus 445 and set the fsb to 533 above.. when ure bios boots.. keep pressing tab etc.. and enter windows mem diagnostic mode..
and run like 5 runs etc just to make sure ure NB/ ram are ok... before u boot into windows.. cause it would be pointless.
Last edited by cstkl1; 10-21-2008 at 03:54 AM.
Ok, please excuse me for my ignorance, just to make sure
I should set everything like you wrote and instead of 7.5 and 533 I should use 9 and 445?
Also is this Linpack you are talking about?
http://www.intel.com/cd/software/pro...mkl/266857.htm
And last what setting is "tRFC 25" ? I can't seem to find it
His comment wasn't directed toward you he was helping some one else. Was there any confusion on what I suggested for you at all? If so I will answer any questions you might have,Ok, please excuse me for my ignorance, just to make sure
I should set everything like you wrote and instead of 7.5 and 533 I should use 9 and 445?
Also is this Linpack you are talking about?
http://www.intel.com/cd/software/pro...mkl/266857.htm
And last what setting is "tRFC 25" ? I can't seem to find it
_____________________________________________
Rig = GA-P67A-UD3P Rev 1.0 - 2600K @ 5.2~GHz 1.5v~, 1.489~v Under Load - Swiftech Water Cooling - 2 X 4GB Corsair DDR3 2000Mhz @ 1868MHz~ 9,10,9,27 @ 1.65v~ - Asus 6970 @ 950MHz / 1450MHz - 3x Western Digital RE3 320Gb 16Mb Cache SataII Drives in Raid0 - Corsair HX 850w Power Supply - Antec 1200 Case - 3DMark 11 Score = P6234 - 3DVantage Score = P26237
tRFC = refresh rate.. anyway both of u guys are practically using the same hardware so sure..Ok, please excuse me for my ignorance, just to make sure
I should set everything like you wrote and instead of 7.5 and 533 I should use 9 and 445?
Also is this Linpack you are talking about?
http://www.intel.com/cd/software/pro...mkl/266857.htm
And last what setting is "tRFC 25" ? I can't seem to find it
use 9x445 to find the vcore..
once u eliminate the vcore out of the settings to ponder it makes life very easy..
then u can go back to 533 fsb.. and just worry about the rams..
and lower the nb voltage from 1.32v to anything that works for ya..
best way to test NB is to run memtest86.
basic way in vista would be downloading hyperPI. disabling the audio/theme etc on it and running dual 32m.
once u gotten all this done.. then go ahead and run orthos for 10 hours which would complete all the fft from 8 to 4096.. and high chance any failures would be ram/nb related
should take u two full days which is y linpack is great...
Oh I'm sorry I just saw e8400 and assumed it was for me
Well I plan on checking memory but I think it should be fine, I've run it at divider without even knowing a few times. But to be sure... what are they rated as? DDR 1066 MHz or? How much is it in FSB? Damn this used to be a lot simpler back in the days
Aside from "PULLINS = Enabled" (don't know what this is) rest is pretty self explanatory, sadly I'm at work right now so I wont be able to test this for a few hours yet
Also how do I check and set my VID? So I can answer yaddam205
use realtemp..Oh I'm sorry I just saw e8400 and assumed it was for me
Well I plan on checking memory but I think it should be fine, I've run it at divider without even knowing a few times. But to be sure... what are they rated as? DDR 1066 MHz or? How much is it in FSB? Damn this used to be a lot simpler back in the days
Aside from "PULLINS = Enabled" (don't know what this is) rest is pretty self explanatory, sadly I'm at work right now so I wont be able to test this for a few hours yet
Also how do I check and set my VID? So I can answer yaddam205
Pullins will increase your PL by a little if you are lucky "it works for some people and some people it doesn't". You can set the fsb strap to 266 and 333 and you will see how it affects the memory speeds just look in the drop down for the memory speed after changing it between 266 and 333 and decide which one you want to use. The lowest setting is always the 1:1 like example you drop down the memory speed box and you will see 900, then below that 11xx, then 1500.. the 900 is 1:1 which would require the PL 10 setting mentioned earlier. If you can use the 11xx then you can use PL 8,,. Once you get in there and do this you will see what I am saying. Yes and use realtemp as mentioned above for the vid question.Oh I'm sorry I just saw e8400 and assumed it was for me
Well I plan on checking memory but I think it should be fine, I've run it at divider without even knowing a few times. But to be sure... what are they rated as? DDR 1066 MHz or? How much is it in FSB? Damn this used to be a lot simpler back in the days
Aside from "PULLINS = Enabled" (don't know what this is) rest is pretty self explanatory, sadly I'm at work right now so I wont be able to test this for a few hours yet
Also how do I check and set my VID? So I can answer yaddam205
Last edited by truehighroller; 10-21-2008 at 05:17 AM.
_____________________________________________
Rig = GA-P67A-UD3P Rev 1.0 - 2600K @ 5.2~GHz 1.5v~, 1.489~v Under Load - Swiftech Water Cooling - 2 X 4GB Corsair DDR3 2000Mhz @ 1868MHz~ 9,10,9,27 @ 1.65v~ - Asus 6970 @ 950MHz / 1450MHz - 3x Western Digital RE3 320Gb 16Mb Cache SataII Drives in Raid0 - Corsair HX 850w Power Supply - Antec 1200 Case - 3DMark 11 Score = P6234 - 3DVantage Score = P26237
I can not run stability in the Prime Blend mode, no voltage in the memory?
Ai Overclock Tuner ................. [Manual]
CPU Ratio Setting .................. [8]
FSB Frequency ...................... [425]
PCIE Frequency ..................... [100]
FSB Strap to North Bridge .......... [Auto]
DRAM Frequency ..................... [1066]
DRAM Clock Skew on Channel A1 ...... [Auto]
DRAM Clock Skew on Channel A2 ...... [Auto]
DRAM Clock Skew on Channel B1 ...... [Auto]
DRAM Clock Skew on Channel B2 ...... [Auto]
DRAM Timing Control ................ [Manual] (5 5-5-15)
DRAM Static Read Control ........... [Disabled]
DRAM Read Training ................. [Disabled]
MEM. OC Charger .................... [Enabled]
Ai Clock Twister ................... [Lighter]
Ai Transaction Booster ............. [Manual] (08-All Disabled)
____________________________________
CPU Voltage ........................ [1.4250]
CPU GTL Voltage Reference (0/2) .... [0.630]
CPU GTL Voltage Reference (1/3) .... [0.670]
CPU PLL Voltage .................... [1.50]
vFSB.................................[1.28]
DRAM Voltage ....................... [2.20]
NB Voltage ......................... [1.18]
NB GTL Reference ................... [0.630]
SB Voltage ......................... [1.10]
PCIE Voltage ....................... [1.50]
____________________________________
Load-Line Calibration .............. [Enabled]
CPU Spread Spectrum ................ [Disabled]
PCIE Spread Spectrum ............... [Disabled]
CPU Clock Skew ..................... [Auto]
NB Clock Skew ...................... [Auto]
CPU Margin Enhancement ............. [Optimized Mode]
Sorry my bad EnglishLanguage Tools
http://www.google.com.br/language_tools?hl=pt-BR
Q9550 | Gigabyte GA-EP45-UD3P (rev. 1.1) | 4x1GB | SLI 98GTX | LC8850 750w
4685.99 Mhz (H20) - http://valid.canardpc.com/show_oc.php?id=689328
WC - CPU Swiftech Apogee GTZ | Enzotech SNBW | VGA Koolance VID-398 | Rad MagiCool 360ST | Pump DP-1200 | MCRES-Micro Rev2.
I think you are running a Q6600 ? Which ram in fact ? Habe you verified the ram voltage with a Digital Multimeter... If your board overvolts the ram as my 2 Dlx do with about 0.08 you are almost pushing 2.3 volts through the ram
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro AsusSaaya yupp, I agree
Hi,
P5Q Del
Chip: Q6600
Bios: 0803
RAM: Corsair 2GB DDR2 XMS2 Dominator PC2-8500C5 TwinX 4GB
I have a 3ghz Oc on my Q6600. Can I get any better settings than what I have now.. Is there anything I can tweak further that will benefit my system?
I have all Advanced CPU settings as disabled.
Thanks for any help in advanced.
I tried and tried and no go, than my rig wouldn't even post so I set everything to default, dropped multi to 8.5, and now I'm running Prime at 475 FSB and 4.12 GHz with no sweat and lower temps... Where I couldn't even run it for a 10 minutes at 450 x 9.
Are there any cons to running high FSB and lower multi but higher clocks?
And it BSOD :/ Damn thing
Quick question. Regarding "PCIE SATA Voltage". 1.6v too high/dangerous? Recommended setting?
[CPU: Q9450 @ 3.6Ghz|RAM: Corsair PC2-8500 (2x2GB)]
[MOBO: Asus P5Q Deluxe (1406)|HDD: Samsung F1 750GB]
[GFX: XFX HD6950 2GB (flashed to HD6970)|PSU: Corsair HX 620W]
I had mine at 1.6v and recently changed it back to auto and have seen no ill effects either way.
Larry
Q9650
Asus P5Q-D Bios 1406
280 GTX FC Block
2x2gb OCZ Flex II PC2 9200
Water Cooled/ Iwaki MD20/ D-Tek Fuzion
XFX 850 Watt
OWC SSD
Code:I can not run stability in the Prime Blend mode, no voltage in the memory? I have a Q6600 VID 1.3250v 4x1gb Trasncend AxeRam Micron DDR-800+ (1.8v 4 4-4-12 2T) Ai Overclock Tuner ................. [Manual] CPU Ratio Setting .................. [8] FSB Frequency ...................... [425] PCIE Frequency ..................... [100] FSB Strap to North Bridge .......... [Auto] DRAM Frequency ..................... [1066] DRAM Clock Skew on Channel A1 ...... [Auto] DRAM Clock Skew on Channel A2 ...... [Auto] DRAM Clock Skew on Channel B1 ...... [Auto] DRAM Clock Skew on Channel B2 ...... [Auto] DRAM Timing Control ................ [Manual] (5 5-5-15) DRAM Static Read Control ........... [Disabled] DRAM Read Training ................. [Disabled] MEM. OC Charger .................... [Enabled] Ai Clock Twister ................... [Lighter] Ai Transaction Booster ............. [Manual] (08-All Disabled) ____________________________________ CPU Voltage ........................ [1.4250] --> WHICH CPU CPU GTL Voltage Reference (0/2) .... [0.630] --> AUTO CPU GTL Voltage Reference (1/3) .... [0.670] --> AUTO CPU PLL Voltage .................... [1.50] --> 1.56 vFSB.................................[1.28] DRAM Voltage ....................... [2.20] --> WHICH RAM NB Voltage ......................... [1.18] --> 1.26 NB GTL Reference ................... [0.630] SB Voltage ......................... [1.10] PCIE Voltage ....................... [1.50] ____________________________________ Load-Line Calibration .............. [Enabled] CPU Spread Spectrum ................ [Disabled] PCIE Spread Spectrum ............... [Disabled] CPU Clock Skew ..................... [Auto] NB Clock Skew ...................... [Auto] CPU Margin Enhancement ............. [Optimized Mode]Yes, I have a Q6600 VID 1.3250v
4x1gb Trasncend AxeRam Micron DDR-800+ (1.8v 4 4-4-12 2T)
Sorry my bad English
http://www.google.com.br/language_tools?hl=pt-BR
Q9550 | Gigabyte GA-EP45-UD3P (rev. 1.1) | 4x1GB | SLI 98GTX | LC8850 750w
4685.99 Mhz (H20) - http://valid.canardpc.com/show_oc.php?id=689328
WC - CPU Swiftech Apogee GTZ | Enzotech SNBW | VGA Koolance VID-398 | Rad MagiCool 360ST | Pump DP-1200 | MCRES-Micro Rev2.
Memory on P5Q-D question - I have (had) 4 1GB sticks until one of them died which I sent back, now the supplier cant replace them with the same model (1 month later on a lifetime warrently GG) so I am thinking sending back the other 2 sticks and just getting 2x2 GB sticks. Problem is most (pretty much all) of the faster sticks these days are much taller so I could have issues with my CPU cooler fan getting in the way (mem sits close on this board)- as it only just fit my current setup with normal height ram.
Question is (after that ramble) is does putting two sticks in channel B and leaving channel A empty hurt/slow down anything?
Side note - if anyone has GSkill PI Series DDR2 PC2 8800 CL5 4GB memory on the P5Q and has had problems let me know - as it is the front runner for new ram ATM.
Current Specs: E8500 @ 4.2GHz | Scythe Ninja Mini|Asus P5Q Deluxe M/board | Patriot PC2-9600 1GBX4 | 8800GTS Fatal1ty Edition, 320MB 650/2000mhz | Samsung 750GB + Deskstar 7K1000 750GB | Pioneer DVR-212BK | G15 Gaming Keyboard | G9 Mouse | Antec P190 | Vista Ultimate 64bit | Dell E248WFP 24" Widescreen Monitor | Dell 5.1 Speakers
So normal size ram fits, I would opt for eg for the Gskill PC8000PQ kit ( blue ones) they are dead cheap to 1080-1130Mhz too... running on my main rig at 450FSB with 1120Mhz ram speed 5-5-5-15-55 1.94volts (bios setting)
If you run the dimms in the 2 furthest slots think it will be single channel ops and bandwith will be reduced... Asus board tend to have one simm slot inbetween...channel A are the yellow ones, black channel B...
If I would remove the 2 dimms on the left : single channels ops mate
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro Asus
Thanks Ill check out the Gskill PC8000PQ kits
The slots I was talking about using were 2 black ones (rather than the far yellow and black) so just leaving the 2 yellows empty - so that should still be running in dual channel (i believe) but for some reason I get the feeling i read somewhere (no idea where or how creadible) that the using the black slots was somehow worse than the yellows - was just not sure by how much (or at all).
Current Specs: E8500 @ 4.2GHz | Scythe Ninja Mini|Asus P5Q Deluxe M/board | Patriot PC2-9600 1GBX4 | 8800GTS Fatal1ty Edition, 320MB 650/2000mhz | Samsung 750GB + Deskstar 7K1000 750GB | Pioneer DVR-212BK | G15 Gaming Keyboard | G9 Mouse | Antec P190 | Vista Ultimate 64bit | Dell E248WFP 24" Widescreen Monitor | Dell 5.1 Speakers
Reply With Quote
Bookmarks