Well I drempt about this board for ages before I finally could afford to get one, £170 it cost me from over--suckers in the UK, anyway, havent had any trouble whatsoever banging this board straight upto 450fsb with my quad Q6600 x 8 @ 3.6ghz) and 4gb OCZ Flex 2 1150mhz running at 1120mhz 5-5-5-15. anyway here's the dilema, but first I will post my settings and then show you the dilema:
This are my current settings:
CPU Feature
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled
Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock
CPU Clock Ratio: 8x
- Target CPU Clock: 3600
CPU Clock: 450
Boot Up Clock: AUTO
DRAM Speed: 266/667
- Target DRAM Speed: 1120
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled
Voltage Settings
CPU VID Control: 1.4875v gives 1.525v with CPU VID Special Add on Auto
CPU VID Special Add: Auto
DRAM Voltage Control: 2.12v gives 2.10v
SB Core/CPU PLL Voltage: 1.510v
NB Core Voltage: 1.555v
CPU VTT Voltage: 1.310v
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.45v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: Auto
x CPU GTL 0/2 REF Volt: Auto
x North Bridge GTL REF Volt: Auto
DRAM Timing
- Enhance Data transmitting: FAST
- Enhance Addressing: FAST
- T2 Dispatch: Disabled
Clock Setting Fine Delay
Ch1 Clock Crossing Setting: Auto- DIMM 1 Clock fine delay: Current
- DIMM 2 Clock fine delay: Curren
- DIMM 1 Control fine delay: Current
- DIMM 2 Control fine delay: Current
- Ch 1 Command fine delay: Current
Ch2 Clock Crossing Setting: Auto
- DIMM 3 Clock fine delay: Current
- DIMM 4 Clock fine delay: Current
- DIMM 3 Control fine delay: Current
- DIMM 4 Control fine delay: Current
- Ch 2 Command fine delay: Current
Ch1Ch2 CommonClock Setting: Auto
Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto
Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto
CAS Latency Time (tCL): 5
RAS# to CAS# Delay (tRCD): 5
RAS# Precharge (tRP): 5
Precharge Delay (tRAS): 15
All Precharge to Act: 6
REF to ACT Delay (tRFC): 52
Performance LVL (Read Delay) (tRD): 7
Read delay phase adjust: Enter
Ch1 Read delay phase (4~0)
- Channel 1 Phase 0 Pull-In: AUTO 7
- Channel 1 Phase 1 Pull-In: AUTO 7
- Channel 1 Phase 2 Pull-In: AUTO 7
- Channel 1 Phase 3 Pull-In: AUTO 7
- Channel 1 Phase 4 Pull-In: AUTO 7
Ch2 Read delay phase (4~0)
- Channel 2 Phase 0 Pull-In: Auto 7
- Channel 2 Phase 1 Pull-In: Auto 7
- Channel 2 Phase 2 Pull-In: Auto 7
- Channel 2 Phase 3 Pull-In: Auto 7
- Channel 2 Phase 4 Pull-In: Auto 7
MCH ODT Latency: 1
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO
Right and here's the dilema: Memory bandwith SUCKS!!!!!!!!!!!!, I mean come on, my P35-T2R was better than this, any suggestions, im already on the latest bios.
Reply With Quote
Bookmarks