Live MB OC Report :: ASUS Rampage Extreme

[DeathWalking]

eternal_fantasy, do you recommend running those 4 sticks of cellshock to get 4gb, or do you think a 2x2gb solution would be better? Basically, how hard was your memory to overclock with 4 sticks.

[eternal_fantasy]

eternal_fantasy, do you recommend running those 4 sticks of cellshock to get 4gb, or do you think a 2x2gb solution would be better? Basically, how hard was your memory to overclock with 4 sticks.

pretty much impossible to overclock the ram with 4x1GB... or at least worth mentioning... 2x2GB is definitely the way to go

[zlojack]

pretty much impossible to overclock the ram with 4x1GB... or at least worth mentioning... 2x4GB is definitely the way to go

2x4??

[DeathWalking]

If any of those kits have reached 1600, I'd get one...I don't know of any, though.

[eternal_fantasy]

2x4??

lol sorry 2x2

[DeathWalking]

I would seriously love a system with 8gb of ram, but the only ones I know of run at unacceptably slow speeds. They're also DDR2.

[MnM]

I dont seem to have any problems with my CSX Diablo memory at all.

OK here is where I am so far:

Rampage Extreme 501 bios
4 x 2 Diablo D9GTR based

[ShoNuff]

I dont seem to have any problems with my CSX Diablo memory at all.

OK here is where I am so far:

Rampage Extreme 501 bios
4 x 2 Diablo D9GTR based

Wow! Impressive especially since you are using a 4x2GB config. What volts for the ram? Looking at your cpu temps it looks like you are on air correct?

It looks like the 501 bios is a keeper!

[Mix]

Hi

Look the spd of one kit csx diablo 2x2gb gtr 2000



How can i change this spd????

[DeathWalking]

I dont seem to have any problems with my CSX Diablo memory at all.

OMFG. You have my exact setup. Please post complete list of settings!

[MnM]

I dont seem to have any problems with my CSX Diablo memory at all.

OK here is where I am so far:

Rampage Extreme 501 bios
4 x 2 Diablo D9GTR based




Extreme Tweaker Menu

CPU FSB - Manual
CPU Level Up - Auto
FSB: 430
-cpu configuration
-cpu clock skew - Auto
-nb clock skew - Auto
FSB Strap to North Bridge - 333
DRAM FREQUENCY - 1721
DRAM Command Rate - Auto
DRAM Timing Control - Manual
*1st information : 8-7-6-15-Auto-Auto-Auto-Auto
*2nd informaion : all AUTO
*3rd information : all AUTO
DRAM Static Read Control - Auto
DRAM Dynamic Write Control - Auto
-DRAM Skew Control
Ai Clock Twister - Auto
Ai Transaction Booster - Auto
*C/P : A1 A2
*LVL : 07 07

EPU II Phase Control - Auto
-----------------------------------------------------------------
*** Please Key in Numbers or select voltage!***
CPU Voltage - 1.462
Load-Line Calibration - Enabled
CPU PLL Voltage - 1.709
FSB Termination Voltage - 1.45
CPU GTLVref (o) - +40
CPU GTLVref (1) - +50
CPU GTLVref (2) - +50
CPU GTLVref (3) - +40
NB GTLVref - +30
North Bridge Voltage - 1.66997
DRAM Voltage -1.96156
NB DDRVref - Auto
DDR3 ChannelA Vref - Auto
DDR3 ChannelB Vref - Auto
South Bridge 1.5 Voltage - 1.6
South Bridge 1.05 Voltage - 1.08
**********************************************
CPU Spread Spectrum - Disabled
PCIE Spread Spectrum - Disabled

well after the discussions in here about the GTLVRef values and what they should be I can confirm that after I changed mine to - (they were + see above) the settings are not stable anymore. PC froze during OCCT (about 30 minutes in). Went back to the original settings above and it passed the 1H test.
So I am not entirely sure that for QX9770 - is the way to go.